/dev/sda,megaraid_disk_00 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-11-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUSMM1680ASS200 Revision: A204 Compliance: SPC-4 User Capacity: 800,166,076,416 bytes [800 GB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x5000cca04fbb4f48 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Sat Jul 12 23:15:27 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 1% Current Drive Temperature: 32 C Drive Trip Temperature: 70 C Manufactured in week 24 of year 2017 Specified cycle count over device lifetime: 0 Accumulated start-stop cycles: 0 Specified load-unload count over device lifetime: 0 Accumulated load-unload cycles: 0 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 14261114267239172 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 26810.368 0 write: 0 0 0 0 0 50230.750 0 verify: 0 0 0 0 0 0.004 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed - 27105 - [- - -] Long (extended) Self-test duration: 5548 seconds [92.5 minutes] Background scan results log Status: no scans active Accumulated power on time, hours:minutes 35923:16 [2155396 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 7 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04fbb4f49 attached SAS address = 0x54cd98f05d1cd903 attached phy identifier = 4 Invalid DWORD count = 18 Running disparity error count = 18 Loss of DWORD synchronization count = 41 Phy reset problem count = 0 relative target port id = 2 generation code = 7 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04fbb4f4a attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_01 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-11-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUSMM1680ASS200 Revision: A204 Compliance: SPC-4 User Capacity: 800,166,076,416 bytes [800 GB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x5000cca04fb367b0 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Sat Jul 12 23:15:27 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 2% Current Drive Temperature: 32 C Drive Trip Temperature: 70 C Manufactured in week 30 of year 2016 Specified cycle count over device lifetime: 0 Accumulated start-stop cycles: 0 Specified load-unload count over device lifetime: 0 Accumulated load-unload cycles: 0 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 19100117906752260 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 64844.923 0 write: 0 0 0 0 0 113652.023 0 verify: 0 0 0 0 0 0.004 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed - 46773 - [- - -] Long (extended) Self-test duration: 5548 seconds [92.5 minutes] Background scan results log Status: no scans active Accumulated power on time, hours:minutes 55590:49 [3335449 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 3 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: power on reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04fb367b1 attached SAS address = 0x54cd98f05d1cd900 attached phy identifier = 0 Invalid DWORD count = 15 Running disparity error count = 15 Loss of DWORD synchronization count = 20 Phy reset problem count = 0 relative target port id = 2 generation code = 3 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04fb367b2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_02 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-11-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUSMM1680ASS200 Revision: A204 Compliance: SPC-4 User Capacity: 800,166,076,416 bytes [800 GB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x5000cca04fbcd2b8 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Sat Jul 12 23:15:27 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 1% Current Drive Temperature: 32 C Drive Trip Temperature: 70 C Manufactured in week 38 of year 2017 Specified cycle count over device lifetime: 0 Accumulated start-stop cycles: 0 Specified load-unload count over device lifetime: 0 Accumulated load-unload cycles: 0 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 17638791372079876 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 59106.403 0 write: 0 0 0 0 0 99096.841 0 verify: 0 0 0 0 0 0.004 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed - 29097 - [- - -] Long (extended) Self-test duration: 5548 seconds [92.5 minutes] Background scan results log Status: no scans active Accumulated power on time, hours:minutes 37915:03 [2274903 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 7 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04fbcd2b9 attached SAS address = 0x54cd98f05d1cd905 attached phy identifier = 6 Invalid DWORD count = 14 Running disparity error count = 14 Loss of DWORD synchronization count = 36 Phy reset problem count = 0 relative target port id = 2 generation code = 7 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04fbcd2ba attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_03 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-11-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUSMM1680ASS200 Revision: A204 Compliance: SPC-4 User Capacity: 800,166,076,416 bytes [800 GB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x5000cca04fb40290 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Sat Jul 12 23:15:27 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 1% Current Drive Temperature: 31 C Drive Trip Temperature: 70 C Manufactured in week 32 of year 2016 Specified cycle count over device lifetime: 0 Accumulated start-stop cycles: 0 Specified load-unload count over device lifetime: 0 Accumulated load-unload cycles: 0 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 14530780885680900 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 29354.403 0 write: 0 0 0 0 0 52096.083 0 verify: 0 0 0 0 0 0.004 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed - 27238 - [- - -] Long (extended) Self-test duration: 5548 seconds [92.5 minutes] Background scan results log Status: no scans active Accumulated power on time, hours:minutes 37186:55 [2231215 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 7 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04fb40291 attached SAS address = 0x54cd98f05d1cd902 attached phy identifier = 2 Invalid DWORD count = 15 Running disparity error count = 15 Loss of DWORD synchronization count = 61 Phy reset problem count = 0 relative target port id = 2 generation code = 7 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04fb40292 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_04 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-11-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUSMM1680ASS200 Revision: A204 Compliance: SPC-4 User Capacity: 800,166,076,416 bytes [800 GB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x5000cca04fb32c9c Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Sat Jul 12 23:15:27 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 2% Current Drive Temperature: 31 C Drive Trip Temperature: 70 C Manufactured in week 30 of year 2016 Specified cycle count over device lifetime: 0 Accumulated start-stop cycles: 0 Specified load-unload count over device lifetime: 0 Accumulated load-unload cycles: 0 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 18475357468360704 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 69236.290 0 write: 0 0 0 0 0 111453.254 0 verify: 0 0 0 0 0 0.004 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed - 46771 - [- - -] Long (extended) Self-test duration: 5548 seconds [92.5 minutes] Background scan results log Status: no scans active Accumulated power on time, hours:minutes 55588:50 [3335330 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 7 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04fb32c9d attached SAS address = 0x54cd98f05d1cd904 attached phy identifier = 5 Invalid DWORD count = 15 Running disparity error count = 15 Loss of DWORD synchronization count = 30 Phy reset problem count = 0 relative target port id = 2 generation code = 7 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04fb32c9e attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_05 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-11-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUSMM1680ASS200 Revision: A204 Compliance: SPC-4 User Capacity: 800,166,076,416 bytes [800 GB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x5000cca04fbcdef4 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Sat Jul 12 23:15:27 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 1% Current Drive Temperature: 31 C Drive Trip Temperature: 70 C Manufactured in week 37 of year 2017 Specified cycle count over device lifetime: 0 Accumulated start-stop cycles: 0 Specified load-unload count over device lifetime: 0 Accumulated load-unload cycles: 0 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 18840856282792708 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 66074.333 0 write: 0 0 0 0 0 112260.726 0 verify: 0 0 0 0 0 0.004 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed - 35642 - [- - -] Long (extended) Self-test duration: 5548 seconds [92.5 minutes] Background scan results log Status: no scans active Accumulated power on time, hours:minutes 45591:19 [2735479 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 7 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04fbcdef5 attached SAS address = 0x54cd98f05d1cd901 attached phy identifier = 1 Invalid DWORD count = 13 Running disparity error count = 13 Loss of DWORD synchronization count = 42 Phy reset problem count = 0 relative target port id = 2 generation code = 7 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04fbcdef6 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0