/dev/sda,megaraid_disk_00 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-56-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Intel S4510/S4610/S4500/S4600 Series SSDs Device Model: INTEL SSDSC2KG240G8 Serial Number: -- LU WWN Device Id: 5 5cd2e4 ... Firmware Version: XCV10110 User Capacity: 240,057,409,536 bytes [240 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jan 30 19:55:01 2023 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 23550 12 Power_Cycle_Count -O--CK 100 100 000 - 32 170 Available_Reservd_Space PO--CK 100 100 010 - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 174 Unsafe_Shutdown_Count -O--CK 100 100 000 - 30 175 Power_Loss_Cap_Test PO--CK 100 100 010 - 2498 (32 65535) 183 SATA_Downshift_Count -O--CK 100 100 000 - 0 184 End-to-End_Error_Count PO--CK 100 100 090 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Drive_Temperature -O---K 076 070 000 - 24 (Min/Max 17/30) 192 Unsafe_Shutdown_Count -O--CK 100 100 000 - 30 194 Temperature_Celsius -O---K 100 100 000 - 24 197 Pending_Sector_Count -O--C- 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 225 Host_Writes_32MiB -O--CK 100 100 000 - 0 226 Workld_Media_Wear_Indic -O--CK 100 100 000 - 30 227 Workld_Host_Reads_Perc -O--CK 100 100 000 - 99 228 Workload_Minutes -O--CK 100 100 000 - 1412807 232 Available_Reservd_Space PO--CK 100 100 010 - 0 233 Media_Wearout_Indicator -O--CK 100 100 000 - 0 234 Thermal_Throttle_Status -O--CK 100 100 000 - 0/0 235 Power_Loss_Cap_Test PO--CK 100 100 010 - 2498 (32 65535) 241 Host_Writes_32MiB -O--CK 100 100 000 - 0 242 Host_Reads_32MiB -O--CK 100 100 000 - 181 243 NAND_Writes_32MiB -O--CK 100 100 000 - 20996 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 8 Comprehensive SMART error log 0x03 GPL R/O 20 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xb8 GPL,SL VS 1 Device vendor specific log 0xb9 GPL VS 3336 Device vendor specific log 0xb9 SL VS 8 Device vendor specific log 0xba GPL VS 1280 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 8 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (20 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 24 Celsius Power Cycle Min/Max Temperature: 17/30 Celsius Lifetime Min/Max Temperature: 3/36 Celsius Specified Max Operating Temperature: 73 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 00 2c 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 32 --- Lifetime Power-On Resets 0x01 0x018 6 19595 --- Logical Sectors Written 0x01 0x020 6 10538222 --- Number of Write Commands 0x01 0x028 6 11912251 --- Logical Sectors Read 0x01 0x030 6 14859671 --- Number of Read Commands 0x01 0x038 6 3177724453 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 24 --- Current Temperature 0x05 0x010 1 24 --- Average Short Term Temperature 0x05 0x018 1 24 --- Average Long Term Temperature 0x05 0x020 1 35 --- Highest Temperature 0x05 0x028 1 11 --- Lowest Temperature 0x05 0x030 1 32 --- Highest Average Short Term Temperature 0x05 0x038 1 19 --- Lowest Average Short Term Temperature 0x05 0x040 1 30 --- Highest Average Long Term Temperature 0x05 0x048 1 22 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 73 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 94 --- Number of Hardware Resets 0x06 0x010 4 94 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x000a 4 4 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS /dev/sda,megaraid_disk_01 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-56-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST600MM0006 Revision: LS0A Compliance: SPC-4 User Capacity: 600,127,266,816 bytes [600 GB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 10000 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c5007edbc78f Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Mon Jan 30 19:55:01 2023 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 30 C Drive Trip Temperature: 50 C Manufactured in week 48 of year 2014 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 189 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 6547 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 3756549153 Blocks received from initiator = 238975129 Blocks read from cache and sent to initiator = 75725661 Number of read and write commands whose size <= segment size = 1713951372 Number of read and write commands whose size > segment size = 94476 Vendor (Seagate/Hitachi) factory information number of hours powered up = 62830.07 number of minutes until next internal SMART test = 4 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 999370471 0 0 999370471 0 70642.506 0 write: 0 0 110291 110291 110291 188077.957 0 verify: 2548138360 2 0 2548138362 2 212197.478 0 Non-medium error count: 134 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 64 39075 - [- - -] # 2 Background short Completed 64 39074 - [- - -] # 3 Background short Completed 64 7 - [- - -] # 4 Reserved(7) Completed 48 7 - [- - -] # 5 Background short Completed 64 5 - [- - -] # 6 Reserved(7) Completed 48 5 - [- - -] # 7 Reserved(7) Aborted (by user command) 48 3 - [- - -] # 8 Background short Completed 64 2 - [- - -] # 9 Reserved(7) Aborted (by user command) 48 1 - [- - -] #10 Reserved(7) Aborted (by user command) 48 1 - [- - -] #11 Background short Completed 64 1 - [- - -] Long (extended) Self-test duration: 3777 seconds [63.0 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 62830:04 [3769804 minutes] Number of background scans performed: 856, scan progress: 0.00% Number of background medium scans performed: 856 # when lba(hex) [sk,asc,ascq] reassign_status 1 4618:53 000000000b9742d5 [1,17,1] Recovered via rewrite in-place 2 4690:53 000000000b9742d5 [1,17,1] Recovered via rewrite in-place 3 4825:20 000000000b8fa77d [1,17,1] Recovered via rewrite in-place 4 4825:20 000000000b9742d5 [1,17,1] Recovered via rewrite in-place 5 5328:52 000000000b9742d5 [1,17,1] Recovered via rewrite in-place 6 5472:54 000000000b9742d5 [1,17,1] Recovered via rewrite in-place 7 5544:53 000000000b9742d5 [1,17,1] Recovered via rewrite in-place 8 5832:44 0000000000e3a681 [1,17,1] Recovered via rewrite in-place 9 7200:52 0000000000c3b904 [1,17,1] Recovered via rewrite in-place 10 7489:09 000000000ab3b89b [1,17,1] Recovered via rewrite in-place 11 8713:04 0000000000f7b904 [1,17,1] Recovered via rewrite in-place 12 10297:32 000000000a3fb8ac [1,17,1] Recovered via rewrite in-place 13 11665:38 00000000010bb8d6 [1,17,1] Recovered via rewrite in-place 14 12025:51 00000000037fbcb6 [1,17,1] Recovered via rewrite in-place 15 14114:10 00000000034fa57f [1,17,1] Recovered via rewrite in-place 16 16778:17 0000000000e3a67f [1,17,1] Recovered via rewrite in-place 17 21170:43 000000000948d453 [1,17,1] Recovered via rewrite in-place 18 21242:56 0000000013ffb86d [1,17,1] Recovered via rewrite in-place 19 21890:41 000000000a3fb8af [1,17,1] Recovered via rewrite in-place 20 22466:35 0000000001bbb8d4 [1,17,1] Recovered via rewrite in-place 21 24986:59 000000001373bd17 [1,17,1] Recovered via rewrite in-place 22 25490:39 00000000010fa6fc [1,17,1] Recovered via rewrite in-place 23 26138:52 000000000f87c0bc [1,17,1] Recovered via rewrite in-place 24 26448:32 000000000d3bb92e [1,17,1] Recovered via rewrite in-place 25 30049:49 000000000023d8ec [1,17,1] Recovered via rewrite in-place 26 30049:49 000000000023d8ed [1,17,1] Recovered via rewrite in-place 27 30338:03 000000000e2fa7cc [1,17,1] Recovered via rewrite in-place 28 31274:05 000000000f17ba1e [1,17,1] Recovered via rewrite in-place 29 32425:55 00000000017bc13b [1,17,1] Recovered via rewrite in-place 30 32786:25 0000000018a7a9fa [1,17,1] Recovered via rewrite in-place 31 33650:14 0000000013e78aaa [1,17,1] Recovered via rewrite in-place 32 34082:14 000000001043c742 [1,17,1] Recovered via rewrite in-place 33 35954:00 00000000000fb904 [1,17,1] Recovered via rewrite in-place 34 37034:11 000000000aa7aae5 [1,17,1] Recovered via rewrite in-place 35 37538:11 00000000095bbc68 [1,17,1] Recovered via rewrite in-place 36 37754:04 00000000001fc3eb [1,17,1] Recovered via rewrite in-place 37 37970:09 000000000537b974 [1,17,1] Recovered via rewrite in-place 38 38690:15 000000000b57c187 [1,17,1] Recovered via rewrite in-place 39 39056:59 000000000068982f [1,17,1] Recovered via rewrite in-place 40 52014:04 0000000006017e80 [1,17,1] Recovered via rewrite in-place 41 52086:03 0000000003f8d258 [1,17,1] Recovered via rewrite in-place 42 54611:55 0000000003f8d257 [1,17,1] Recovered via rewrite in-place 43 61785:05 00000000027a636c [1,17,1] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: power on reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5007edbc78d attached SAS address = 0x514187702fec2e00 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 2 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 2 Phy reset problem count: 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5007edbc78e attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sda,megaraid_disk_02 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-56-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST600MM0006 Revision: LS08 Compliance: SPC-4 User Capacity: 600,127,266,816 bytes [600 GB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 10000 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c500716b79df Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Mon Jan 30 19:55:01 2023 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 27 C Drive Trip Temperature: 50 C Manufactured in week 03 of year 2014 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 175 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 6451 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 3126641305 Blocks received from initiator = 397930511 Blocks read from cache and sent to initiator = 1348437052 Number of read and write commands whose size <= segment size = 810041045 Number of read and write commands whose size > segment size = 99217 Vendor (Seagate/Hitachi) factory information number of hours powered up = 70489.38 number of minutes until next internal SMART test = 51 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 1102674920 0 0 1102674920 0 43128.420 0 write: 0 0 1242 1242 1242 97571.593 0 verify: 1087103141 0 0 1087103141 0 209289.921 0 Non-medium error count: 61 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 48 46734 - [- - -] # 2 Background short Completed 48 46734 - [- - -] # 3 Background short Completed 48 8 - [- - -] # 4 Reserved(7) Completed 32 8 - [- - -] # 5 Background short Completed 48 7 - [- - -] # 6 Background short Completed 48 4 - [- - -] # 7 Reserved(7) Completed 32 4 - [- - -] # 8 Background short Completed 48 2 - [- - -] Long (extended) Self-test duration: 3777 seconds [63.0 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 70489:23 [4229363 minutes] Number of background scans performed: 965, scan progress: 0.00% Number of background medium scans performed: 965 # when lba(hex) [sk,asc,ascq] reassign_status 1 7737:46 000000000d1ee562 [1,17,1] Recovered via rewrite in-place 2 14992:31 0000000002cce6c4 [1,17,1] Recovered via rewrite in-place 3 16848:59 000000000d1ee562 [1,17,1] Recovered via rewrite in-place 4 17065:13 000000004108ff0e [1,17,1] Recovered via rewrite in-place 5 17136:55 000000004108ff0b [1,17,1] Recovered via rewrite in-place 6 17136:55 000000004108ff0c [1,17,1] Recovered via rewrite in-place 7 17136:55 000000004108ff0f [1,17,1] Recovered via rewrite in-place 8 17136:55 000000004108ff18 [1,17,1] Recovered via rewrite in-place 9 17136:55 000000004108ff19 [1,17,1] Recovered via rewrite in-place 10 20437:07 000000000d1ee562 [1,17,1] Recovered via rewrite in-place 11 24393:52 0000000018e8a378 [1,17,1] Recovered via rewrite in-place 12 26983:19 0000000006373bd7 [1,17,1] Recovered via rewrite in-place 13 30220:24 000000000107394d [1,17,1] Recovered via rewrite in-place 14 32666:13 00000000012338ce [1,17,1] Recovered via rewrite in-place 15 33457:44 000000000d1ee562 [1,17,1] Recovered via rewrite in-place 16 37855:04 00000000012338cf [1,17,1] Recovered via rewrite in-place 17 39372:15 0000000030b726a8 [1,17,1] Recovered via rewrite in-place 18 40523:21 0000000035b72b96 [1,17,1] Recovered via rewrite in-place 19 40666:36 000000000d1ee562 [1,17,1] Recovered via rewrite in-place 20 44263:56 000000002c0b286b [1,17,1] Recovered via rewrite in-place 21 55631:42 000000000d1ee562 [1,17,1] Recovered via rewrite in-place 22 58448:51 0000000040800ba6 [1,17,1] Recovered via rewrite in-place 23 58663:55 000000000d1ee562 [1,17,1] Recovered via rewrite in-place 24 64933:44 000000000d1ee562 [1,17,1] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500716b79dd attached SAS address = 0x514187702fec2e04 attached phy identifier = 6 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 8 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 8 Phy reset problem count: 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500716b79de attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sda,megaraid_disk_03 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-56-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST600MM0006 Revision: LS0A Compliance: SPC-4 User Capacity: 600,127,266,816 bytes [600 GB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 10000 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c5007edbbce3 Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Mon Jan 30 19:55:06 2023 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 28 C Drive Trip Temperature: 50 C Manufactured in week 48 of year 2014 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 166 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 4589 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 3606277112 Blocks received from initiator = 1527903828 Blocks read from cache and sent to initiator = 918973111 Number of read and write commands whose size <= segment size = 362988165 Number of read and write commands whose size > segment size = 86068 Vendor (Seagate/Hitachi) factory information number of hours powered up = 63142.47 number of minutes until next internal SMART test = 4 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 2243588941 0 0 2243588941 0 53591.648 0 write: 0 0 2230 2230 2230 41947.994 0 verify: 4117977272 0 0 4117977272 0 209564.871 0 Non-medium error count: 29 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 64 39388 - [- - -] # 2 Background short Completed 64 39388 - [- - -] # 3 Background short Completed 64 2 - [- - -] # 4 Reserved(7) Completed 48 2 - [- - -] # 5 Background short Completed 64 1 - [- - -] Long (extended) Self-test duration: 3777 seconds [63.0 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 63142:28 [3788548 minutes] Number of background scans performed: 869, scan progress: 0.00% Number of background medium scans performed: 869 # when lba(hex) [sk,asc,ascq] reassign_status 1 4198:34 0000000001cc06b0 [1,17,1] Recovered via rewrite in-place 2 14711:38 0000000003ffba81 [1,17,1] Recovered via rewrite in-place 3 18672:04 0000000003efb889 [1,17,1] Recovered via rewrite in-place 4 29330:28 0000000044b67986 [1,17,1] Recovered via rewrite in-place 5 39388:04 0000000000b83dc8 [1,17,1] Recovered via rewrite in-place 6 40537:43 0000000044b67986 [1,17,1] Recovered via rewrite in-place 7 47858:57 0000000044b67986 [1,17,1] Recovered via rewrite in-place 8 51751:44 0000000044b67986 [1,17,1] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5007edbbce1 attached SAS address = 0x514187702fec2e02 attached phy identifier = 2 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 3 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 3 Phy reset problem count: 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5007edbbce2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sda,megaraid_disk_04 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-56-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST600MM0006 Revision: LS08 Compliance: SPC-4 User Capacity: 600,127,266,816 bytes [600 GB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 10000 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c50070a7f077 Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Mon Jan 30 19:55:06 2023 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 26 C Drive Trip Temperature: 50 C Manufactured in week 46 of year 2013 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 151 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 2740 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 3513409026 Blocks received from initiator = 174204965 Blocks read from cache and sent to initiator = 45480463 Number of read and write commands whose size <= segment size = 309468933 Number of read and write commands whose size > segment size = 981 Vendor (Seagate/Hitachi) factory information number of hours powered up = 71308.93 number of minutes until next internal SMART test = 27 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 761743507 0 0 761743507 0 1856.786 0 write: 0 0 0 0 0 43980.520 0 verify: 1129341529 0 0 1129341529 0 204451.242 0 Non-medium error count: 41 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 48 48384 - [- - -] # 2 Background short Completed 48 48383 - [- - -] # 3 Background short Completed 48 3 - [- - -] # 4 Reserved(7) Completed 32 3 - [- - -] # 5 Background short Completed 48 1 - [- - -] Long (extended) Self-test duration: 3777 seconds [63.0 minutes] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 71308:56 [4278536 minutes] Number of background scans performed: 812, scan progress: 0.70% Number of background medium scans performed: 812 # when lba(hex) [sk,asc,ascq] reassign_status 1 14878:27 00000000006758e1 [1,17,1] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50070a7f075 attached SAS address = 0x514187702fec2e03 attached phy identifier = 5 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 3 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 3 Phy reset problem count: 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50070a7f076 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0