/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.1-desktop-1omv2290] (OpenMandriva Lx 7.3-2) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F3 Device Model: SAMSUNG HD103SJ Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 1AJ100E5 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Jan 28 05:52:31 2023 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x83) Offline data collection activity is in a Reserved state. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9240) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 154) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 3938 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 072 068 025 - 8745 4 Start_Stop_Count -O--CK 090 090 000 - 10606 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 46206 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 252 252 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4942 191 G-Sense_Error_Rate -O---K 100 100 000 - 34 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 051 000 - 32 (Min/Max 9/49) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 1102 223 Load_Retry_Count -O--CK 252 252 000 - 0 225 Load_Cycle_Count -O--CK 099 099 000 - 10786 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xbb GPL VS 4 Device vendor specific log 0xbc GPL VS 2 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 63580 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 63580 [3] occurred at disk power-on lifetime: 45505 hours (1896 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 78 08 62 58 e0 00 Error: IDNF 1 sectors at LBA = 0x78086258 = 2013815384 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 78 08 62 58 e0 08 00:00:38.181 READ DMA EXT 25 00 00 00 01 00 00 78 08 61 48 e0 08 00:00:38.181 READ DMA EXT 35 00 00 00 05 00 00 03 e6 0f 88 e0 08 00:00:38.181 WRITE DMA EXT 35 00 00 00 03 00 00 02 1f 56 30 e0 08 00:00:38.181 WRITE DMA EXT b0 00 d0 00 01 00 00 00 c2 4f 01 e0 08 00:00:38.181 SMART READ DATA Error 63579 [2] occurred at disk power-on lifetime: 45505 hours (1896 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 78 08 61 48 e0 00 Error: IDNF 1 sectors at LBA = 0x78086148 = 2013815112 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 78 08 61 48 e0 08 00:00:38.181 READ DMA EXT 35 00 00 00 05 00 00 03 e6 0f 88 e0 08 00:00:38.181 WRITE DMA EXT 35 00 00 00 03 00 00 02 1f 56 30 e0 08 00:00:38.181 WRITE DMA EXT b0 00 d0 00 01 00 00 00 c2 4f 01 e0 08 00:00:38.181 SMART READ DATA 25 00 00 00 01 00 00 64 48 5f b8 e0 08 00:00:38.181 READ DMA EXT Error 63578 [1] occurred at disk power-on lifetime: 45505 hours (1896 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 78 08 5c c0 e0 00 Error: IDNF 1 sectors at LBA = 0x78085cc0 = 2013813952 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 78 08 5c c0 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 d4 47 0d 28 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 d4 47 0d 28 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 64 48 5a 70 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 64 48 59 a0 e0 08 00:00:38.180 READ DMA EXT Error 63577 [0] occurred at disk power-on lifetime: 45505 hours (1896 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 d4 47 0d 28 e0 00 Error: IDNF 1 sectors at LBA = 0xd4470d28 = 3561426216 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 d4 47 0d 28 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 64 48 5a 70 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 64 48 59 a0 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 78 08 59 b0 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 64 48 57 e0 e0 08 00:00:38.180 READ DMA EXT Error 63576 [7] occurred at disk power-on lifetime: 45505 hours (1896 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 78 08 59 b0 e0 00 Error: IDNF 1 sectors at LBA = 0x780859b0 = 2013813168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 78 08 59 b0 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 64 48 57 e0 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 64 48 57 18 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 bf 82 e0 f0 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 64 48 55 e8 e0 08 00:00:38.180 READ DMA EXT Error 63575 [6] occurred at disk power-on lifetime: 45505 hours (1896 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 bf 82 e0 f0 e0 00 Error: IDNF 1 sectors at LBA = 0xbf82e0f0 = 3213025520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 bf 82 e0 f0 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 64 48 55 e8 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 64 48 54 d8 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 bf 82 de d8 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 64 48 53 98 e0 08 00:00:38.180 READ DMA EXT Error 63574 [5] occurred at disk power-on lifetime: 45505 hours (1896 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 bf 82 de d8 e0 00 Error: IDNF 1 sectors at LBA = 0xbf82ded8 = 3213024984 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 bf 82 de d8 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 64 48 53 98 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 64 48 53 08 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 64 48 52 78 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 64 48 52 78 e0 08 00:00:38.180 READ DMA EXT Error 63573 [4] occurred at disk power-on lifetime: 45505 hours (1896 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 78 08 52 98 e0 00 Error: IDNF 1 sectors at LBA = 0x78085298 = 2013811352 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 78 08 52 98 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 64 48 50 b0 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 64 48 4f 98 e0 08 00:00:38.180 READ DMA EXT 25 00 00 00 01 00 00 78 08 4f 78 e0 08 00:00:38.180 READ DMA EXT 35 00 00 00 08 00 00 00 5b ef 78 e0 08 00:00:38.179 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 42265 - # 2 Short offline Completed without error 00% 34418 - # 3 Short offline Completed without error 00% 34206 - # 4 Short offline Completed without error 00% 34188 - # 5 Short offline Completed without error 00% 27200 - # 6 Short offline Completed without error 00% 27079 - # 7 Short offline Completed without error 00% 27078 - # 8 Short offline Completed without error 00% 26992 - # 9 Short offline Completed without error 00% 26869 - #10 Extended offline Aborted by host 80% 26824 - #11 Short offline Completed without error 00% 26787 - #12 Short offline Completed without error 00% 26653 - #13 Short offline Completed without error 00% 26628 - #14 Short offline Completed without error 00% 26576 - #15 Short offline Completed without error 00% 26553 - #16 Short offline Completed without error 00% 26532 - #17 Short offline Completed without error 00% 26532 - #18 Short offline Completed without error 00% 26506 - #19 Short offline Completed without error 00% 26478 - #20 Short offline Completed without error 00% 26445 - #21 Short offline Completed without error 00% 26424 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 27/31 Celsius Lifetime Min/Max Temperature: 12/49 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (62) Index Estimated Time Temperature Celsius 63 2023-01-27 19:15 30 *********** ... ..( 13 skipped). .. *********** 77 2023-01-27 20:25 30 *********** 78 2023-01-27 20:30 29 ********** ... ..( 21 skipped). .. ********** 100 2023-01-27 22:20 29 ********** 101 2023-01-27 22:25 28 ********* ... ..( 6 skipped). .. ********* 108 2023-01-27 23:00 28 ********* 109 2023-01-27 23:05 29 ********** ... ..( 17 skipped). .. ********** 127 2023-01-28 00:35 29 ********** 0 2023-01-28 00:40 28 ********* ... ..( 27 skipped). .. ********* 28 2023-01-28 03:00 28 ********* 29 2023-01-28 03:05 27 ******** ... ..( 4 skipped). .. ******** 34 2023-01-28 03:30 27 ******** 35 2023-01-28 03:35 28 ********* ... ..( 8 skipped). .. ********* 44 2023-01-28 04:20 28 ********* 45 2023-01-28 04:25 29 ********** ... ..( 11 skipped). .. ********** 57 2023-01-28 05:25 29 ********** 58 2023-01-28 05:30 30 *********** ... ..( 3 skipped). .. *********** 62 2023-01-28 05:50 30 *********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 27 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 16 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.1-desktop-1omv2290] (OpenMandriva Lx 7.3-2) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba P300 (CMR) Device Model: TOSHIBA HDWD110 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: MS2OA8R0 User Capacity: 1,000,203,804,160 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Jan 28 05:52:31 2023 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7312) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 122) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 1 2 Throughput_Performance P-S--- 141 141 054 - 72 3 Spin_Up_Time POS--- 122 122 024 - 175 (Average 200) 4 Start_Stop_Count -O--C- 100 100 000 - 579 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 118 118 020 - 33 9 Power_On_Hours -O--C- 099 099 000 - 11231 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 437 192 Power-Off_Retract_Count -O--CK 100 100 000 - 1001 193 Load_Cycle_Count -O--C- 100 100 000 - 1001 194 Temperature_Celsius -O---- 193 193 000 - 31 (Min/Max 12/43) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 29/34 Celsius Lifetime Min/Max Temperature: 12/43 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (60) Index Estimated Time Temperature Celsius 61 2023-01-28 03:45 29 ********** ... ..( 30 skipped). .. ********** 92 2023-01-28 04:16 29 ********** 93 2023-01-28 04:17 30 *********** ... ..( 51 skipped). .. *********** 17 2023-01-28 05:09 30 *********** 18 2023-01-28 05:10 31 ************ 19 2023-01-28 05:11 31 ************ 20 2023-01-28 05:12 30 *********** 21 2023-01-28 05:13 31 ************ 22 2023-01-28 05:14 30 *********** 23 2023-01-28 05:15 31 ************ 24 2023-01-28 05:16 31 ************ 25 2023-01-28 05:17 31 ************ 26 2023-01-28 05:18 30 *********** 27 2023-01-28 05:19 31 ************ ... ..( 2 skipped). .. ************ 30 2023-01-28 05:22 31 ************ 31 2023-01-28 05:23 30 *********** 32 2023-01-28 05:24 31 ************ ... ..( 12 skipped). .. ************ 45 2023-01-28 05:37 31 ************ 46 2023-01-28 05:38 32 ************* ... ..( 7 skipped). .. ************* 54 2023-01-28 05:46 32 ************* 55 2023-01-28 05:47 31 ************ ... ..( 4 skipped). .. ************ 60 2023-01-28 05:52 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 437 --- Lifetime Power-On Resets 0x01 0x010 4 11231 --- Power-on Hours 0x01 0x018 6 11097473254 --- Logical Sectors Written 0x01 0x020 6 133767681 --- Number of Write Commands 0x01 0x028 6 17305207786 --- Logical Sectors Read 0x01 0x030 6 148397272 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 11004 --- Spindle Motor Power-on Hours 0x03 0x010 4 11004 --- Head Flying Hours 0x03 0x018 4 1001 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 11 --- Read Recovery Attempts 0x03 0x030 4 14 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 24 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 2 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 32 --- Current Temperature 0x05 0x010 1 30 N-- Average Short Term Temperature 0x05 0x018 1 30 N-- Average Long Term Temperature 0x05 0x020 1 43 --- Highest Temperature 0x05 0x028 1 12 --- Lowest Temperature 0x05 0x030 1 40 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 37 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 9677 --- Number of Hardware Resets 0x06 0x010 4 5398 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 28 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 16 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS