/dev/sda === START OF INFORMATION SECTION === Device Model: WDC WD10JPCX-24UE4T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Oct 17 01:21:22 2020 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (18240) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 204) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 17 3 Spin_Up_Time POS--K 175 173 021 - 2233 4 Start_Stop_Count -O--CK 058 058 000 - 42808 5 Reallocated_Sector_Ct PO--CK 196 196 140 - 191 7 Seek_Error_Rate POSR-K 200 200 051 - 0 9 Power_On_Hours -O--CK 085 085 000 - 11111 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 5419 192 Power-Off_Retract_Count -O--CK 200 200 000 - 173 193 Load_Cycle_Count -O--CK 144 144 000 - 169479 194 Temperature_Celsius -O---K 117 098 000 - 30 196 Reallocated_Event_Count -O--CK 161 161 000 - 39 197 Current_Pending_Sector -O--CK 200 200 000 - 8 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 001 000 - 3694 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 9 240 Head_Flying_Hours -O--CK 086 086 000 - 10577 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 38 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 10277 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 10277 [4] occurred at disk power-on lifetime: 10988 hours (457 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 c0 08 40 40 00 Error: UNC at LBA = 0x02c00840 = 46139456 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 f0 00 00 03 c0 08 00 40 08 01:55:18.881 READ FPDMA QUEUED 60 00 38 00 e8 00 00 03 80 08 48 40 08 01:55:18.881 READ FPDMA QUEUED 60 00 08 00 e0 00 00 03 80 08 00 40 08 01:55:18.881 READ FPDMA QUEUED 60 00 10 00 d8 00 00 03 40 08 00 40 08 01:55:18.881 READ FPDMA QUEUED 60 00 08 00 d0 00 00 03 00 08 00 40 08 01:55:18.881 READ FPDMA QUEUED Error 10276 [3] occurred at disk power-on lifetime: 10973 hours (457 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3e 00 34 50 40 00 Error: UNC at LBA = 0x3e003450 = 1040200784 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 28 00 00 3c 41 24 18 40 08 04:44:36.561 READ FPDMA QUEUED 60 00 08 00 20 00 00 3c 41 24 10 40 08 04:44:36.556 READ FPDMA QUEUED 60 00 08 00 a8 00 00 3d c1 15 28 40 08 04:44:36.549 READ FPDMA QUEUED 60 00 08 00 a0 00 00 3e 81 0b 00 40 08 04:44:36.543 READ FPDMA QUEUED 60 00 08 00 98 00 00 3d 81 1e 40 40 08 04:44:36.543 READ FPDMA QUEUED Error 10275 [2] occurred at disk power-on lifetime: 10973 hours (457 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 2a 40 09 30 40 00 Error: UNC at LBA = 0x2a400930 = 708839728 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 70 00 38 00 00 2a 40 09 00 40 08 04:44:29.815 READ FPDMA QUEUED 60 00 70 00 f0 00 00 58 80 09 00 40 08 04:44:29.798 READ FPDMA QUEUED 60 01 08 00 50 00 00 3c 00 09 00 40 08 04:44:29.786 READ FPDMA QUEUED 60 01 08 00 e8 00 00 1c 40 09 00 40 08 04:44:29.761 READ FPDMA QUEUED 60 00 08 00 30 00 00 60 80 09 00 40 08 04:44:29.731 READ FPDMA QUEUED Error 10274 [1] occurred at disk power-on lifetime: 10972 hours (457 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 00 18 00 40 00 Error: UNC at LBA = 0x00001800 = 6144 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 b0 00 00 00 00 18 00 40 08 04:16:35.917 READ FPDMA QUEUED 60 00 08 00 a8 00 00 00 00 10 00 40 08 04:16:35.912 READ FPDMA QUEUED 60 00 08 00 a0 00 00 00 00 0c 00 40 08 04:16:35.909 READ FPDMA QUEUED 60 00 08 00 98 00 00 00 00 0a 00 40 08 04:16:35.908 READ FPDMA QUEUED 60 00 08 00 90 00 00 00 00 09 00 40 08 04:16:35.886 READ FPDMA QUEUED Error 10273 [0] occurred at disk power-on lifetime: 10972 hours (457 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 00 00 00 40 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 90 00 00 00 00 00 00 40 08 04:13:20.985 READ FPDMA QUEUED 60 00 68 00 c8 00 00 74 70 67 88 40 08 04:13:20.984 READ FPDMA QUEUED 60 00 80 00 c0 00 00 74 70 67 00 40 08 04:13:20.984 READ FPDMA QUEUED 60 00 f8 00 b8 00 00 74 70 66 00 40 08 04:13:20.984 READ FPDMA QUEUED 60 02 00 00 00 00 00 74 70 64 00 40 08 04:13:20.982 READ FPDMA QUEUED Error 10272 [23] occurred at disk power-on lifetime: 10972 hours (457 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 00 18 00 40 00 Error: UNC at LBA = 0x00001800 = 6144 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 60 00 00 00 00 18 00 40 08 04:13:16.777 READ FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 00 08 04:13:16.777 CHECK POWER MODE 60 00 20 00 98 00 00 3a 04 08 00 40 08 04:13:16.775 READ FPDMA QUEUED 60 00 08 00 90 00 00 3a 04 07 f8 40 08 04:13:16.775 READ FPDMA QUEUED 60 00 08 00 88 00 00 00 00 2c b0 40 08 04:13:16.775 READ FPDMA QUEUED Error 10271 [22] occurred at disk power-on lifetime: 10972 hours (457 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 00 20 00 40 00 Error: UNC at LBA = 0x00002000 = 8192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 08 00 00 00 00 20 00 40 08 04:13:11.402 READ FPDMA QUEUED 60 00 08 00 00 00 00 00 00 10 00 40 08 04:13:11.393 READ FPDMA QUEUED 60 00 08 00 f8 00 00 00 00 08 00 40 08 04:13:11.359 READ FPDMA QUEUED 60 00 08 00 b8 00 00 00 00 04 00 40 08 04:13:11.359 READ FPDMA QUEUED 60 00 08 00 b0 00 00 00 00 02 00 40 08 04:13:11.359 READ FPDMA QUEUED Error 10270 [21] occurred at disk power-on lifetime: 10972 hours (457 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 00 18 00 40 00 Error: UNC at LBA = 0x00001800 = 6144 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 88 00 00 00 00 18 00 40 08 04:12:19.204 READ FPDMA QUEUED 60 00 08 00 80 00 00 00 00 10 00 40 08 04:12:19.199 READ FPDMA QUEUED 60 00 08 00 58 00 00 00 00 0c 00 40 08 04:12:19.196 READ FPDMA QUEUED 60 00 08 00 50 00 00 00 00 0a 00 40 08 04:12:19.195 READ FPDMA QUEUED 60 00 08 00 48 00 00 00 00 09 00 40 08 04:12:19.173 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Vendor (0x50) Completed without error 00% 192 - # 2 Short offline Completed without error 00% 192 - # 3 Vendor (0x50) Completed without error 00% 189 - # 4 Short offline Completed without error 00% 189 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 21/30 Celsius Lifetime Min/Max Temperature: 15/50 Celsius Specified Max Operating Temperature: 30 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (86) Index Estimated Time Temperature Celsius 87 2020-10-16 23:14 34 *************** ... ..( 4 skipped). .. *************** 92 2020-10-16 23:19 34 *************** 93 2020-10-16 23:20 ? - 94 2020-10-16 23:21 21 ** ... ..( 2 skipped). .. ** 97 2020-10-16 23:24 21 ** 98 2020-10-16 23:25 ? - 99 2020-10-16 23:26 21 ** 100 2020-10-16 23:27 22 *** 101 2020-10-16 23:28 22 *** 102 2020-10-16 23:29 22 *** 103 2020-10-16 23:30 ? - 104 2020-10-16 23:31 22 *** 105 2020-10-16 23:32 22 *** 106 2020-10-16 23:33 23 **** 107 2020-10-16 23:34 23 **** 108 2020-10-16 23:35 24 ***** 109 2020-10-16 23:36 24 ***** 110 2020-10-16 23:37 25 ****** 111 2020-10-16 23:38 26 ******* ... ..( 3 skipped). .. ******* 115 2020-10-16 23:42 26 ******* 116 2020-10-16 23:43 27 ******** ... ..( 6 skipped). .. ******** 123 2020-10-16 23:50 27 ******** 124 2020-10-16 23:51 28 ********* ... ..( 5 skipped). .. ********* 2 2020-10-16 23:57 28 ********* 3 2020-10-16 23:58 29 ********** ... ..( 12 skipped). .. ********** 16 2020-10-17 00:11 29 ********** 17 2020-10-17 00:12 30 *********** ... ..( 68 skipped). .. *********** 86 2020-10-17 01:21 30 *********** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 61 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 40 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 7659 Vendor specific /dev/sdb === START OF INFORMATION SECTION === Model Family: WD Blue and Green SSDs Device Model: WDC WDS240G2G0A-00JH30 Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: UF360000 User Capacity: 240,065,183,744 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Oct 17 01:21:22 2020 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 32) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x15) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 42) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 6919 12 Power_Cycle_Count -O--CK 100 100 000 - 1914 165 Block_Erase_Count -O--CK 100 100 000 - 5352 166 Minimum_PE_Cycles_TLC -O--CK 100 100 --- - 58 167 Max_Bad_Blocks_per_Die -O--CK 100 100 --- - 0 168 Maximum_PE_Cycles_TLC -O--CK 100 100 --- - 72 169 Total_Bad_Blocks -O--CK 100 100 --- - 213 170 Grown_Bad_Blocks -O--CK 100 100 --- - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Average_PE_Cycles_TLC -O--CK 100 100 000 - 58 174 Unexpected_Power_Loss -O--CK 100 100 000 - 1098 184 End-to-End_Error -O--CK 100 100 --- - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 --- - 0 194 Temperature_Celsius -O---K 069 055 000 - 31 (Min/Max 9/55) 199 UDMA_CRC_Error_Count -O--CK 100 100 --- - 0 230 Media_Wearout_Indicator -O--CK 100 100 000 - 0x0f1d0b3c0f1d 232 Available_Reservd_Space PO--CK 100 100 005 - 100 233 NAND_GB_Written_TLC -O--CK 100 100 --- - 14610 234 NAND_GB_Written_SLC -O--CK 100 100 000 - 40809 241 Host_Writes_GiB ----CK 100 100 000 - 16565 242 Host_Reads_GiB ----CK 100 100 000 - 13593 244 Temp_Throttle_Status -O--CK 000 100 --- - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3 GPL,SL VS 1 Device vendor specific log 0xa7 GPL,SL VS 1 Device vendor specific log 0xa9 GPL,SL VS 3 Device vendor specific log Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Invalid Self-test Log index = 0x0014 (reserved = 0x00) Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1914 --- Lifetime Power-On Resets 0x01 0x010 4 6919 --- Power-on Hours 0x01 0x018 6 34741066623 --- Logical Sectors Written 0x01 0x028 6 28506901844 --- Logical Sectors Read 0x01 0x038 6 6922 --- Date and Time TimeStamp 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 31 --- Current Temperature 0x05 0x010 1 - --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 53 --- Highest Temperature 0x05 0x028 1 22 --- Lowest Temperature 0x05 0x030 1 43 --- Highest Average Short Term Temperature 0x05 0x038 1 43 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 95 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 11 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 35 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 36 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0001 2 0 Command failed due to ICRC error