/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.13.12-200.fc34.x86_64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG MZ7TD256HAFV-000L9 Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: DXT02L5Q User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available, deterministic, zeroed Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Aug 24 13:34:32 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (53956) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 40) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 9 Power_On_Hours -O--CK 097 097 000 - 11084 12 Power_Cycle_Count -O--CK 096 096 000 - 3401 175 Program_Fail_Count_Chip -O--CK 100 100 010 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 010 - 0 177 Wear_Leveling_Count PO--C- 089 089 005 - 130 178 Used_Rsvd_Blk_Cnt_Chip PO--C- 100 100 010 - 0 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 6240 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 073 043 000 - 27 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 CRC_Error_Count -OSRCK 253 253 000 - 2 233 Media_Wearout_Indicator -O-RCK 199 199 000 - 9793953 234 Unknown_Samsung_Attr -O--C- 100 100 000 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 308 236 Unknown_Samsung_Attr -O--C- 099 099 000 - 83 237 Unknown_Samsung_Attr -O--C- 099 099 000 - 130 238 Unknown_Samsung_Attr -O--C- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 1 Comprehensive SMART error log 0x03 GPL,SL R/O 1 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 1 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 16 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 10940 - # 2 Short offline Completed without error 00% 10934 - # 3 Short offline Completed without error 00% 10909 - # 4 Short offline Completed without error 00% 10885 - # 5 Short offline Completed without error 00% 10861 - # 6 Short offline Completed without error 00% 10808 - # 7 Short offline Completed without error 00% 10799 - # 8 Short offline Completed without error 00% 10786 - # 9 Short offline Completed without error 00% 10757 - #10 Short offline Completed without error 00% 10743 - #11 Short offline Completed without error 00% 10718 - #12 Short offline Completed without error 00% 10694 - #13 Short offline Completed without error 00% 10670 - #14 Short offline Completed without error 00% 10646 - #15 Short offline Completed without error 00% 10640 - #16 Short offline Completed without error 00% 10607 - #17 Short offline Completed without error 00% 10597 - #18 Short offline Completed without error 00% 10574 - #19 Short offline Completed without error 00% 10550 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SCT command executing in background (5) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 23/40 Celsius Lifetime Min/Max Temperature: 0/70 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 3 (Unknown, should be 2) Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (30) Index Estimated Time Temperature Celsius 31 2021-08-24 11:27 ? - ... ..( 95 skipped). .. - 127 2021-08-24 13:03 ? - 0 2021-08-24 13:04 40 ********************* 1 2021-08-24 13:05 23 **** 2 2021-08-24 13:06 24 ***** 3 2021-08-24 13:07 27 ******** 4 2021-08-24 13:08 25 ****** ... ..( 24 skipped). .. ****** 29 2021-08-24 13:33 25 ****** 30 2021-08-24 13:34 27 ******** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 7 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.13.12-200.fc34.x86_64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate BarraCuda 3.5 (CMR) Device Model: ST1000DM010-2EP102 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC43 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Aug 24 13:34:32 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 112) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 070 063 006 - 12158430 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 735 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 067 060 045 - 5796158 9 Power_On_Hours -O--CK 098 098 000 - 2492 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 099 099 020 - 1071 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 091 091 000 - 9 188 Command_Timeout -O--CK 100 100 000 - 0 0 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 071 064 040 - 29 (Min/Max 17/29) 193 Load_Cycle_Count -O--CK 100 100 000 - 1541 194 Temperature_Celsius -O---K 029 015 000 - 29 (0 15 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 012 001 000 - 12158430 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 2285h+14m+16.021s 241 Total_LBAs_Written ------ 100 253 000 - 6031149398 242 Total_LBAs_Read ------ 100 253 000 - 9800417584 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4120 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 4800 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 9 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 9 [8] occurred at disk power-on lifetime: 970 hours (40 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 3a 52 b7 00 00 Error: UNC at LBA = 0x023a52b7 = 37376695 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 02 3a 52 b7 e0 00 00:38:42.830 READ DMA EXT 25 00 00 00 20 00 00 20 21 88 12 e0 00 00:38:42.830 READ DMA EXT 25 00 00 00 01 00 00 02 3a 52 b6 e0 00 00:38:40.538 READ DMA EXT 35 00 00 00 08 00 00 00 5b 1f 08 e0 00 00:38:40.538 WRITE DMA EXT 25 00 00 00 20 00 00 20 21 87 82 e0 00 00:38:40.537 READ DMA EXT Error 8 [7] occurred at disk power-on lifetime: 970 hours (40 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 3a 52 b6 00 00 Error: UNC at LBA = 0x023a52b6 = 37376694 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 02 3a 52 b6 e0 00 00:38:40.538 READ DMA EXT 35 00 00 00 08 00 00 00 5b 1f 08 e0 00 00:38:40.538 WRITE DMA EXT 25 00 00 00 20 00 00 20 21 87 82 e0 00 00:38:40.537 READ DMA EXT 25 00 00 00 01 00 00 02 3a 52 b5 e0 00 00:38:38.238 READ DMA EXT 35 00 00 00 08 00 00 00 60 08 58 e0 00 00:38:38.237 WRITE DMA EXT Error 7 [6] occurred at disk power-on lifetime: 970 hours (40 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 3a 52 b5 00 00 Error: UNC at LBA = 0x023a52b5 = 37376693 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 02 3a 52 b5 e0 00 00:38:38.238 READ DMA EXT 35 00 00 00 08 00 00 00 60 08 58 e0 00 00:38:38.237 WRITE DMA EXT 25 00 00 00 20 00 00 20 21 87 62 e0 00 00:38:38.237 READ DMA EXT 35 00 00 00 08 00 00 0e 54 ea 40 e0 00 00:38:38.237 WRITE DMA EXT 35 00 00 00 08 00 00 0a d7 00 e8 e0 00 00:38:38.236 WRITE DMA EXT Error 6 [5] occurred at disk power-on lifetime: 970 hours (40 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 3a 52 b4 00 00 Error: UNC at LBA = 0x023a52b4 = 37376692 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 02 3a 52 b4 e0 00 00:38:35.964 READ DMA EXT 35 00 00 00 08 00 00 01 f8 65 18 e0 00 00:38:35.963 WRITE DMA EXT 35 00 00 00 08 00 00 00 60 cb 90 e0 00 00:38:35.962 WRITE DMA EXT 35 00 00 00 08 00 00 00 01 57 b8 e0 00 00:38:35.962 WRITE DMA EXT ea 00 00 00 00 3a 52 b3 00 00 00 a0 00 00:38:35.927 FLUSH CACHE EXT Error 5 [4] occurred at disk power-on lifetime: 970 hours (40 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 3a 52 b3 00 00 Error: UNC at LBA = 0x023a52b3 = 37376691 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 02 3a 52 b3 e0 00 00:38:33.643 READ DMA EXT 25 00 00 00 20 00 00 20 21 87 f2 e0 00 00:38:33.643 READ DMA EXT 35 00 00 00 08 00 00 00 5b 1f 98 e0 00 00:38:33.643 WRITE DMA EXT 25 00 00 00 01 00 00 02 3a 52 b2 e0 00 00:38:31.370 READ DMA EXT 35 00 00 00 38 00 00 00 5c 89 08 e0 00 00:38:31.369 WRITE DMA EXT Error 4 [3] occurred at disk power-on lifetime: 970 hours (40 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 3a 52 b2 00 00 Error: UNC at LBA = 0x023a52b2 = 37376690 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 02 3a 52 b2 e0 00 00:38:31.370 READ DMA EXT 35 00 00 00 38 00 00 00 5c 89 08 e0 00 00:38:31.369 WRITE DMA EXT ea 00 00 00 00 3a 52 b1 00 00 00 a0 00 00:38:31.334 FLUSH CACHE EXT 25 00 00 00 01 00 00 02 3a 52 b1 e0 00 00:38:29.073 READ DMA EXT 35 00 00 00 10 00 00 00 5b 1f 18 e0 00 00:38:29.073 WRITE DMA EXT Error 3 [2] occurred at disk power-on lifetime: 970 hours (40 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 3a 52 b1 00 00 Error: UNC at LBA = 0x023a52b1 = 37376689 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 02 3a 52 b1 e0 00 00:38:29.073 READ DMA EXT 35 00 00 00 10 00 00 00 5b 1f 18 e0 00 00:38:29.073 WRITE DMA EXT 25 00 00 00 20 00 00 20 21 87 3a e0 00 00:38:29.032 READ DMA EXT 25 00 00 00 01 00 00 02 3a 52 b0 e0 00 00:38:26.780 READ DMA EXT 25 00 00 00 01 00 00 02 3a 52 af e0 00 00:38:26.778 READ DMA EXT Error 2 [1] occurred at disk power-on lifetime: 970 hours (40 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 3a 52 b0 00 00 Error: UNC at LBA = 0x023a52b0 = 37376688 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 02 3a 52 b0 e0 00 00:38:26.780 READ DMA EXT 25 00 00 00 01 00 00 02 3a 52 af e0 00 00:38:26.778 READ DMA EXT 25 00 00 00 01 00 00 02 3a 52 ae e0 00 00:38:26.778 READ DMA EXT 25 00 00 00 01 00 00 02 3a 52 ad e0 00 00:38:26.778 READ DMA EXT 25 00 00 00 01 00 00 02 3a 52 ac e0 00 00:38:26.778 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 2463 - # 2 Short offline Completed without error 00% 2436 - # 3 Extended offline Completed without error 00% 2408 - # 4 Short offline Completed without error 00% 2406 - # 5 Short offline Completed without error 00% 2384 - # 6 Short offline Completed without error 00% 2360 - # 7 Short offline Completed without error 00% 2298 - # 8 Short offline Completed without error 00% 2274 - # 9 Short offline Completed without error 00% 2250 - #10 Short offline Completed without error 00% 2249 - #11 Short offline Completed without error 00% 2242 - #12 Short offline Completed without error 00% 2218 - #13 Short offline Completed without error 00% 2194 - #14 Short offline Completed without error 00% 2171 - #15 Short offline Completed without error 00% 2158 - #16 Short offline Completed without error 00% 2141 - #17 Short offline Completed without error 00% 2117 - #18 Short offline Completed without error 00% 2112 - #19 Short offline Completed without error 00% 2099 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 17/29 Celsius Lifetime Min/Max Temperature: 14/35 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1071 --- Lifetime Power-On Resets 0x01 0x010 4 2492 --- Power-on Hours 0x01 0x018 6 6143084087 --- Logical Sectors Written 0x01 0x020 6 32704442 --- Number of Write Commands 0x01 0x028 6 9997413215 --- Logical Sectors Read 0x01 0x030 6 49198622 --- Number of Read Commands 0x01 0x038 6 - --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 640643019 N-- Spindle Motor Power-on Hours 0x03 0x010 4 640642307 N-- Head Flying Hours 0x03 0x018 4 1541 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 9 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 29 --- Current Temperature 0x05 0x010 1 29 --- Average Short Term Temperature 0x05 0x018 1 27 --- Average Long Term Temperature 0x05 0x020 1 36 --- Highest Temperature 0x05 0x028 1 20 --- Lowest Temperature 0x05 0x030 1 31 --- Highest Average Short Term Temperature 0x05 0x038 1 25 --- Lowest Average Short Term Temperature 0x05 0x040 1 29 --- Highest Average Long Term Temperature 0x05 0x048 1 26 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 13 --- Specified Minimum Operating Temperature |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS