/dev/sda === START OF INFORMATION SECTION === Device Model: Hitachi HTS725032A7E630 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: GHBOA3C0 User Capacity: 320,072,933,376 bytes [320 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Wed Aug 19 14:18:45 2020 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 90) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 099 062 - 0 2 Throughput_Performance P-S--K 197 100 040 - 135 3 Spin_Up_Time PO---K 227 100 033 - 1 4 Start_Stop_Count -O--CK 097 097 000 - 4984 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate POSR-K 100 100 067 - 0 8 Seek_Time_Performance P-S--K 112 100 040 - 35 9 Power_On_Hours -O--CK 041 041 000 - 25862 10 Spin_Retry_Count PO--CK 100 100 060 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 4667 183 Runtime_Bad_Block -O--CK 069 069 000 - 31 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 096 000 - 666159284241 188 Command_Timeout -O--CK 100 097 000 - 627094978633 190 Airflow_Temperature_Cel -O---K 059 037 045 Past 41 (Min/Max 22/41) 191 G-Sense_Error_Rate -O--CK 037 037 000 - 16147 192 Power-Off_Retract_Count -O--CK 100 100 000 - 4522053 193 Load_Cycle_Count -O--CK 001 001 000 - 1341117 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 139 223 Load_Retry_Count -O-R-K 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 156 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 156 [3] occurred at disk power-on lifetime: 9613 hours (400 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 19 00 00 02 a3 28 8f 02 00 Error: ICRC, ABRT 25 sectors at LBA = 0x02a3288f = 44247183 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 78 00 00 02 a3 28 30 e2 00 00:00:10.505 READ DMA EXT 25 00 00 00 78 00 00 02 a3 27 b8 e2 00 00:00:10.504 READ DMA EXT 25 00 00 00 78 00 00 02 a3 27 40 e2 00 00:00:10.503 READ DMA EXT 25 00 00 00 78 00 00 02 a3 26 c8 e2 00 00:00:10.502 READ DMA EXT 25 00 00 00 78 00 00 02 a3 26 50 e2 00 00:00:10.500 READ DMA EXT Error 155 [2] occurred at disk power-on lifetime: 9611 hours (400 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 30 00 00 00 c5 0d 77 00 00 Error: ICRC, ABRT at LBA = 0x00c50d77 = 12914039 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 f0 00 00 03 a2 4b f8 40 00 00:00:36.677 READ FPDMA QUEUED 60 00 08 00 e8 00 00 00 84 c1 48 40 00 00:00:36.672 READ FPDMA QUEUED 61 00 10 00 e0 00 00 08 10 62 f8 40 00 00:00:36.672 WRITE FPDMA QUEUED 61 00 08 00 d8 00 00 08 10 62 f0 40 00 00:00:36.672 WRITE FPDMA QUEUED 61 00 10 00 d0 00 00 01 26 df 18 40 00 00:00:36.672 WRITE FPDMA QUEUED Error 154 [1] occurred at disk power-on lifetime: 9611 hours (400 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 01 00 00 01 2a ca c7 01 00 Error: ICRC, ABRT at LBA = 0x012acac7 = 19581639 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 18 00 b0 00 00 02 21 61 b8 40 00 00:00:29.890 READ FPDMA QUEUED 60 00 08 00 a8 00 00 02 21 e5 80 40 00 00:00:29.889 READ FPDMA QUEUED 60 00 10 00 a0 00 00 01 2b 20 78 40 00 00:00:29.886 READ FPDMA QUEUED 60 00 08 00 98 00 00 02 21 63 70 40 00 00:00:29.886 READ FPDMA QUEUED 60 00 08 00 90 00 00 02 21 63 68 40 00 00:00:29.883 READ FPDMA QUEUED Error 153 [0] occurred at disk power-on lifetime: 9611 hours (400 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 09 00 00 02 21 62 c7 02 00 Error: ICRC, ABRT at LBA = 0x022162c7 = 35742407 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 78 00 00 01 2b 0e f8 40 00 00:00:29.082 READ FPDMA QUEUED 60 00 3f 00 70 00 00 01 01 1c c0 40 00 00:00:29.076 READ FPDMA QUEUED 60 00 18 00 68 00 00 02 21 62 b8 40 00 00:00:29.064 READ FPDMA QUEUED 60 00 10 00 60 00 00 01 2b 11 48 40 00 00:00:29.064 READ FPDMA QUEUED 60 00 08 00 58 00 00 02 21 7d f0 40 00 00:00:29.062 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 19089 - # 2 Short offline Completed without error 00% 19088 - # 3 Short offline Completed without error 00% 18513 - # 4 Short offline Completed without error 00% 18512 - # 5 Short offline Completed without error 00% 18275 - # 6 Short offline Completed without error 00% 17958 - # 7 Short offline Completed without error 00% 17519 - # 8 Short offline Completed without error 00% 16962 - # 9 Short offline Completed without error 00% 16465 - #10 Short offline Completed without error 00% 16064 - #11 Short offline Aborted by host 60% 15301 - #12 Short offline Completed without error 00% 14777 - #13 Short offline Completed without error 00% 14528 - #14 Short offline Completed without error 00% 14527 - #15 Short offline Completed without error 00% 14018 - #16 Short offline Completed without error 00% 14017 - #17 Short offline Completed without error 00% 13468 - #18 Short offline Completed without error 00% 13467 - #19 Short offline Completed without error 00% 13003 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 22/41 Celsius Lifetime Min/Max Temperature: 9/63 Celsius Specified Max Operating Temperature: 38 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (0) Index Estimated Time Temperature Celsius 1 2020-08-19 12:11 43 ************************ ... ..( 24 skipped). .. ************************ 26 2020-08-19 12:36 43 ************************ 27 2020-08-19 12:37 42 *********************** ... ..( 4 skipped). .. *********************** 32 2020-08-19 12:42 42 *********************** 33 2020-08-19 12:43 43 ************************ 34 2020-08-19 12:44 43 ************************ 35 2020-08-19 12:45 ? - 36 2020-08-19 12:46 20 * 37 2020-08-19 12:47 22 *** 38 2020-08-19 12:48 24 ***** 39 2020-08-19 12:49 25 ****** 40 2020-08-19 12:50 27 ******** 41 2020-08-19 12:51 27 ******** 42 2020-08-19 12:52 29 ********** 43 2020-08-19 12:53 30 *********** 44 2020-08-19 12:54 31 ************ 45 2020-08-19 12:55 31 ************ 46 2020-08-19 12:56 32 ************* 47 2020-08-19 12:57 33 ************** 48 2020-08-19 12:58 33 ************** 49 2020-08-19 12:59 34 *************** 50 2020-08-19 13:00 34 *************** 51 2020-08-19 13:01 34 *************** 52 2020-08-19 13:02 35 **************** 53 2020-08-19 13:03 35 **************** 54 2020-08-19 13:04 36 ***************** 55 2020-08-19 13:05 36 ***************** 56 2020-08-19 13:06 36 ***************** 57 2020-08-19 13:07 37 ****************** ... ..( 2 skipped). .. ****************** 60 2020-08-19 13:10 37 ****************** 61 2020-08-19 13:11 ? - 62 2020-08-19 13:12 35 **************** 63 2020-08-19 13:13 35 **************** 64 2020-08-19 13:14 36 ***************** 65 2020-08-19 13:15 36 ***************** 66 2020-08-19 13:16 37 ****************** ... ..( 2 skipped). .. ****************** 69 2020-08-19 13:19 37 ****************** 70 2020-08-19 13:20 36 ***************** ... ..( 3 skipped). .. ***************** 74 2020-08-19 13:24 36 ***************** 75 2020-08-19 13:25 37 ****************** 76 2020-08-19 13:26 37 ****************** 77 2020-08-19 13:27 38 ******************* 78 2020-08-19 13:28 38 ******************* 79 2020-08-19 13:29 38 ******************* 80 2020-08-19 13:30 39 ******************** 81 2020-08-19 13:31 39 ******************** 82 2020-08-19 13:32 39 ******************** 83 2020-08-19 13:33 40 ********************* ... ..( 8 skipped). .. ********************* 92 2020-08-19 13:42 40 ********************* 93 2020-08-19 13:43 41 ********************** 94 2020-08-19 13:44 40 ********************* 95 2020-08-19 13:45 41 ********************** ... ..( 2 skipped). .. ********************** 98 2020-08-19 13:48 41 ********************** 99 2020-08-19 13:49 ? - 100 2020-08-19 13:50 ? - 101 2020-08-19 13:51 24 ***** 102 2020-08-19 13:52 26 ******* 103 2020-08-19 13:53 27 ******** 104 2020-08-19 13:54 28 ********* 105 2020-08-19 13:55 29 ********** 106 2020-08-19 13:56 30 *********** 107 2020-08-19 13:57 32 ************* 108 2020-08-19 13:58 33 ************** 109 2020-08-19 13:59 33 ************** 110 2020-08-19 14:00 34 *************** 111 2020-08-19 14:01 35 **************** 112 2020-08-19 14:02 36 ***************** 113 2020-08-19 14:03 37 ****************** 114 2020-08-19 14:04 37 ****************** 115 2020-08-19 14:05 38 ******************* 116 2020-08-19 14:06 38 ******************* 117 2020-08-19 14:07 37 ****************** 118 2020-08-19 14:08 38 ******************* 119 2020-08-19 14:09 38 ******************* 120 2020-08-19 14:10 39 ******************** 121 2020-08-19 14:11 39 ******************** 122 2020-08-19 14:12 40 ********************* 123 2020-08-19 14:13 40 ********************* 124 2020-08-19 14:14 41 ********************** 125 2020-08-19 14:15 40 ********************* 126 2020-08-19 14:16 40 ********************* 127 2020-08-19 14:17 41 ********************** 0 2020-08-19 14:18 41 ********************** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 99 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 18 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS