/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue EIDE Device Model: WDC WD2500AAJB-00J3A0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.03E01 User Capacity: 250 059 350 016 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) Transport Type: Parallel, ATA8-APT Local Time is: Sat Aug 6 11:10:08 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 5580) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 68) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 6 3 Spin_Up_Time POS--K 138 134 021 - 4100 4 Start_Stop_Count -O--CK 095 095 000 - 5146 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 078 078 000 - 16403 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3279 192 Power-Off_Retract_Count -O--CK 200 200 000 - 355 193 Load_Cycle_Count -O--CK 199 199 000 - 5146 194 Temperature_Celsius -O---K 101 089 000 - 42 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 11 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 21 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 21 [20] occurred at disk power-on lifetime: 13905 hours (579 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 8d e1 53 e7 00 Error: UNC at LBA = 0x078de153 = 126738771 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 00 00 8d e1 50 e7 00 00:08:31.102 READ DMA 25 00 00 00 08 00 00 10 46 25 b8 e0 00 00:08:31.101 READ DMA EXT 25 00 00 00 08 00 00 10 46 25 b0 e0 00 00:08:31.101 READ DMA EXT 25 00 00 00 08 00 00 10 46 25 a8 e0 00 00:08:31.101 READ DMA EXT 25 00 00 00 08 00 00 10 46 25 a0 e0 00 00:08:31.100 READ DMA EXT Error 20 [19] occurred at disk power-on lifetime: 13905 hours (579 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 8d e1 53 e7 00 Error: UNC at LBA = 0x078de153 = 126738771 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 00 00 8d e1 50 e7 00 00:08:28.603 READ DMA 25 00 00 00 08 00 00 10 46 23 b8 e0 00 00:08:28.602 READ DMA EXT 25 00 00 00 08 00 00 10 46 23 b0 e0 00 00:08:28.602 READ DMA EXT 25 00 00 00 08 00 00 10 46 23 a8 e0 00 00:08:28.602 READ DMA EXT 25 00 00 00 08 00 00 10 46 23 a0 e0 00 00:08:28.601 READ DMA EXT Error 19 [18] occurred at disk power-on lifetime: 13905 hours (579 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 8d e1 53 e7 00 Error: UNC at LBA = 0x078de153 = 126738771 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 00 00 8d e1 50 e7 00 00:08:26.086 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:08:26.075 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:08:26.066 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:08:26.059 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:08:26.059 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 18 [17] occurred at disk power-on lifetime: 13905 hours (579 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 8d e1 53 e7 00 Error: UNC at LBA = 0x078de153 = 126738771 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 00 00 8d e1 50 e7 00 00:08:23.832 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:08:23.825 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:08:23.816 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:08:23.809 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:08:23.809 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 17 [16] occurred at disk power-on lifetime: 13905 hours (579 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 8d e1 53 e7 00 Error: UNC at LBA = 0x078de153 = 126738771 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 00 00 8d e1 50 e7 00 00:08:21.427 READ DMA c8 00 00 00 08 00 00 00 8d e1 48 e7 00 00:08:21.427 READ DMA c8 00 00 00 08 00 00 00 8d e1 40 e7 00 00:08:21.427 READ DMA c8 00 00 00 08 00 00 00 8d e1 38 e7 00 00:08:21.426 READ DMA c8 00 00 00 08 00 00 00 8d e1 30 e7 00 00:08:21.426 READ DMA Error 16 [15] occurred at disk power-on lifetime: 13905 hours (579 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 8d e1 53 e7 00 Error: UNC at LBA = 0x078de153 = 126738771 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 00 00 00 00 8d e0 c0 e7 00 00:08:19.157 READ DMA c8 00 00 00 00 00 00 00 8d df c0 e7 00 00:08:19.155 READ DMA c8 00 00 00 00 00 00 00 8d de c0 e7 00 00:08:19.154 READ DMA c8 00 00 00 00 00 00 00 8d dd c0 e7 00 00:08:19.152 READ DMA c8 00 00 00 00 00 00 00 8d dc c0 e7 00 00:08:19.151 READ DMA Error 15 [14] occurred at disk power-on lifetime: 7258 hours (302 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 00 9c 40 e3 00 Error: UNC at LBA = 0x03009c40 = 50371648 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 00 00 00 9c 3f e3 00 03:36:44.653 READ DMA c8 00 00 00 08 00 00 00 00 9d d7 e3 00 03:36:44.653 READ DMA c8 00 00 00 08 00 00 00 cb a1 ff e1 00 03:36:44.652 READ DMA c8 00 00 00 08 00 00 00 cb a2 07 e1 00 03:36:44.651 READ DMA c8 00 00 00 50 00 00 00 cc 0d 97 e1 00 03:36:44.651 READ DMA Error 14 [13] occurred at disk power-on lifetime: 7258 hours (302 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 00 9c 40 e3 00 Error: UNC at LBA = 0x03009c40 = 50371648 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 38 00 00 00 00 9c 0f e3 00 03:36:41.999 READ DMA c8 00 00 00 08 00 00 00 00 9b ef e3 00 03:36:41.998 READ DMA c8 00 00 00 08 00 00 00 00 9c 47 e3 00 03:36:41.982 READ DMA c8 00 00 00 08 00 00 00 00 9b 37 e3 00 03:36:41.981 READ DMA c8 00 00 00 08 00 00 00 00 9b f7 e3 00 03:36:41.980 READ DMA SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 42 Celsius Power Cycle Min/Max Temperature: 26/42 Celsius Lifetime Min/Max Temperature: 26/54 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (100) Index Estimated Time Temperature Celsius 101 2016-08-06 09:03 45 ************************** ... ..( 9 skipped). .. ************************** 111 2016-08-06 09:13 45 ************************** 112 2016-08-06 09:14 44 ************************* ... ..( 17 skipped). .. ************************* 2 2016-08-06 09:32 44 ************************* 3 2016-08-06 09:33 ? - 4 2016-08-06 09:34 27 ******** 5 2016-08-06 09:35 28 ********* 6 2016-08-06 09:36 29 ********** 7 2016-08-06 09:37 30 *********** 8 2016-08-06 09:38 30 *********** 9 2016-08-06 09:39 31 ************ 10 2016-08-06 09:40 32 ************* 11 2016-08-06 09:41 33 ************** 12 2016-08-06 09:42 33 ************** 13 2016-08-06 09:43 33 ************** 14 2016-08-06 09:44 34 *************** 15 2016-08-06 09:45 34 *************** 16 2016-08-06 09:46 34 *************** 17 2016-08-06 09:47 35 **************** 18 2016-08-06 09:48 35 **************** 19 2016-08-06 09:49 36 ***************** 20 2016-08-06 09:50 36 ***************** 21 2016-08-06 09:51 37 ****************** ... ..( 3 skipped). .. ****************** 25 2016-08-06 09:55 37 ****************** 26 2016-08-06 09:56 38 ******************* 27 2016-08-06 09:57 38 ******************* 28 2016-08-06 09:58 38 ******************* 29 2016-08-06 09:59 39 ******************** ... ..( 2 skipped). .. ******************** 32 2016-08-06 10:02 39 ******************** 33 2016-08-06 10:03 40 ********************* ... ..( 3 skipped). .. ********************* 37 2016-08-06 10:07 40 ********************* 38 2016-08-06 10:08 41 ********************** ... ..( 7 skipped). .. ********************** 46 2016-08-06 10:16 41 ********************** 47 2016-08-06 10:17 ? - 48 2016-08-06 10:18 26 ******* 49 2016-08-06 10:19 26 ******* 50 2016-08-06 10:20 26 ******* 51 2016-08-06 10:21 27 ******** 52 2016-08-06 10:22 28 ********* 53 2016-08-06 10:23 29 ********** 54 2016-08-06 10:24 30 *********** 55 2016-08-06 10:25 31 ************ 56 2016-08-06 10:26 32 ************* 57 2016-08-06 10:27 33 ************** 58 2016-08-06 10:28 33 ************** 59 2016-08-06 10:29 33 ************** 60 2016-08-06 10:30 34 *************** 61 2016-08-06 10:31 34 *************** 62 2016-08-06 10:32 34 *************** 63 2016-08-06 10:33 35 **************** 64 2016-08-06 10:34 36 ***************** 65 2016-08-06 10:35 36 ***************** 66 2016-08-06 10:36 37 ****************** ... ..( 2 skipped). .. ****************** 69 2016-08-06 10:39 37 ****************** 70 2016-08-06 10:40 38 ******************* 71 2016-08-06 10:41 38 ******************* 72 2016-08-06 10:42 39 ******************** 73 2016-08-06 10:43 39 ******************** 74 2016-08-06 10:44 40 ********************* ... ..( 2 skipped). .. ********************* 77 2016-08-06 10:47 40 ********************* 78 2016-08-06 10:48 41 ********************** ... ..( 5 skipped). .. ********************** 84 2016-08-06 10:54 41 ********************** 85 2016-08-06 10:55 42 *********************** ... ..( 14 skipped). .. *********************** 100 2016-08-06 11:10 42 *********************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x8000 4 3600 Vendor specific /dev/sdb === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Device Model: WDC WD800BB-55JKA0 Serial Number: -- Firmware Version: 05.01C05 User Capacity: 80 025 280 000 bytes [80,0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-6 (minor revision not indicated) Local Time is: Sat Aug 6 11:10:08 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Unknown SCT Status format version 1, should be 2 or 3. Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2460) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 35) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x001f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 0 3 Spin_Up_Time PO---- 106 089 021 - 2050 4 Start_Stop_Count -O--CK 092 092 000 - 8273 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-- 200 200 051 - 0 9 Power_On_Hours -O--CK 055 055 000 - 32879 10 Spin_Retry_Count PO--C- 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 5880 194 Temperature_Celsius -O---K 105 081 000 - 38 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate P--R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning Read SMART Log Directory failed: scsi error badly formed scsi parameters General Purpose Log Directory not supported SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 No Errors Logged SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Unknown SCT Status format version 1, should be 2 or 3. Unknown SCT Status format version 1, should be 2 or 3. SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) not supported /dev/sdc === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F1 DT Device Model: SAMSUNG HD252HJ Serial Number: -- LU WWN Device Id: 5 0000f0 ... Firmware Version: 1AC01113 User Capacity: 250 059 350 016 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b Local Time is: Sat Aug 6 11:10:09 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3832) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 65) minutes. Conveyance self-test routine recommended polling time: ( 8) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0 3 Spin_Up_Time POS--- 094 094 011 - 2810 4 Start_Stop_Count -O--CK 096 096 000 - 4447 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 100 100 051 - 0 8 Seek_Time_Performance P-S--K 100 100 015 - 9612 9 Power_On_Hours -O--CK 095 095 000 - 23964 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 000 - 3 12 Power_Cycle_Count -O--CK 096 096 000 - 4208 13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 0 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 070 052 000 - 30 (Min/Max 18/30) 194 Temperature_Celsius -O---K 064 051 000 - 36 (Min/Max 18/36) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 310185 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 100 100 000 - 1 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 10566 hours (440 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 53 00 02 00 00 02 53 65 dd 40 00 Error: ABRT 2 sectors at LBA = 0x025365dd = 39019997 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 08 00 00 02 53 65 d7 40 00 04:05:09.190 WRITE DMA EXT 35 00 00 00 08 00 00 02 53 65 cf 40 00 04:05:09.190 WRITE DMA EXT 35 00 00 00 08 00 00 02 53 65 c7 40 00 04:05:09.190 WRITE DMA EXT 35 00 00 00 08 00 00 02 53 65 bf 40 00 04:05:09.190 WRITE DMA EXT 35 00 00 00 08 00 00 02 53 65 b7 40 00 04:05:09.190 WRITE DMA EXT SMART Extended Self-test Log Version: 0 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 7247 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Max Temperature: 36 Celsius Lifetime Max Temperature: 49 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (63) Index Estimated Time Temperature Celsius 64 2016-08-06 09:03 36 ***************** ... ..( 6 skipped). .. ***************** 71 2016-08-06 09:10 36 ***************** 72 2016-08-06 09:11 37 ****************** ... ..( 2 skipped). .. ****************** 75 2016-08-06 09:14 37 ****************** 76 2016-08-06 09:15 36 ***************** ... ..( 9 skipped). .. ***************** 86 2016-08-06 09:25 36 ***************** 87 2016-08-06 09:26 37 ****************** ... ..( 2 skipped). .. ****************** 90 2016-08-06 09:29 37 ****************** 91 2016-08-06 09:30 ? - 92 2016-08-06 09:31 20 * 93 2016-08-06 09:32 21 ** 94 2016-08-06 09:33 21 ** 95 2016-08-06 09:34 22 *** 96 2016-08-06 09:35 23 **** 97 2016-08-06 09:36 24 ***** 98 2016-08-06 09:37 24 ***** 99 2016-08-06 09:38 25 ****** 100 2016-08-06 09:39 25 ****** 101 2016-08-06 09:40 26 ******* 102 2016-08-06 09:41 27 ******** 103 2016-08-06 09:42 27 ******** 104 2016-08-06 09:43 28 ********* 105 2016-08-06 09:44 28 ********* 106 2016-08-06 09:45 29 ********** 107 2016-08-06 09:46 29 ********** 108 2016-08-06 09:47 29 ********** 109 2016-08-06 09:48 30 *********** 110 2016-08-06 09:49 30 *********** 111 2016-08-06 09:50 30 *********** 112 2016-08-06 09:51 31 ************ ... ..( 2 skipped). .. ************ 115 2016-08-06 09:54 31 ************ 116 2016-08-06 09:55 32 ************* ... ..( 2 skipped). .. ************* 119 2016-08-06 09:58 32 ************* 120 2016-08-06 09:59 33 ************** ... ..( 3 skipped). .. ************** 124 2016-08-06 10:03 33 ************** 125 2016-08-06 10:04 34 *************** 126 2016-08-06 10:05 34 *************** 127 2016-08-06 10:06 34 *************** 0 2016-08-06 10:07 ? - 1 2016-08-06 10:08 18 - 2 2016-08-06 10:09 19 - 3 2016-08-06 10:10 20 * 4 2016-08-06 10:11 20 * 5 2016-08-06 10:12 21 ** 6 2016-08-06 10:13 22 *** 7 2016-08-06 10:14 22 *** 8 2016-08-06 10:15 23 **** 9 2016-08-06 10:16 24 ***** 10 2016-08-06 10:17 25 ****** 11 2016-08-06 10:18 25 ****** 12 2016-08-06 10:19 26 ******* 13 2016-08-06 10:20 26 ******* 14 2016-08-06 10:21 27 ******** 15 2016-08-06 10:22 27 ******** 16 2016-08-06 10:23 28 ********* 17 2016-08-06 10:24 28 ********* 18 2016-08-06 10:25 29 ********** 19 2016-08-06 10:26 29 ********** 20 2016-08-06 10:27 29 ********** 21 2016-08-06 10:28 30 *********** 22 2016-08-06 10:29 30 *********** 23 2016-08-06 10:30 31 ************ ... ..( 2 skipped). .. ************ 26 2016-08-06 10:33 31 ************ 27 2016-08-06 10:34 32 ************* ... ..( 2 skipped). .. ************* 30 2016-08-06 10:37 32 ************* 31 2016-08-06 10:38 33 ************** ... ..( 3 skipped). .. ************** 35 2016-08-06 10:42 33 ************** 36 2016-08-06 10:43 34 *************** ... ..( 2 skipped). .. *************** 39 2016-08-06 10:46 34 *************** 40 2016-08-06 10:47 35 **************** ... ..( 6 skipped). .. **************** 47 2016-08-06 10:54 35 **************** 48 2016-08-06 10:55 36 ***************** ... ..( 14 skipped). .. ***************** 63 2016-08-06 11:10 36 ***************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 18 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 18 Transition from drive PhyRdy to drive PhyNRdy 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC