/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD10EZEX-22BN5A0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1 000 204 886 016 bytes [1,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Aug 30 21:21:11 2016 YEKT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 121) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: (11760) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 122) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 114 3 Spin_Up_Time POS--K 170 168 021 - 2466 4 Start_Stop_Count -O--CK 100 100 000 - 72 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 083 083 000 - 12614 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 65 192 Power-Off_Retract_Count -O--CK 200 200 000 - 35 193 Load_Cycle_Count -O--CK 200 200 000 - 180 194 Temperature_Celsius -O---K 109 096 000 - 34 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 1 198 Offline_Uncorrectable ----CK 200 200 000 - 1 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 88 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 88 [15] occurred at disk power-on lifetime: 12348 hours (514 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 ef ef 47 40 00 Error: UNC at LBA = 0x01efef47 = 32501575 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 38 00 00 01 ef ef 47 40 08 1d+06:16:27.609 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+06:16:27.609 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 1d+06:16:27.609 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 1d+06:16:27.608 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 1d+06:16:27.608 SET FEATURES [Set transfer mode] Error 87 [14] occurred at disk power-on lifetime: 12348 hours (514 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 ef ef 46 40 00 Error: UNC at LBA = 0x01efef46 = 32501574 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 b8 00 00 01 ef ef 46 40 08 1d+06:16:23.622 READ FPDMA QUEUED 60 00 01 00 b0 00 00 01 ef ef 47 40 08 1d+06:16:23.622 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+06:16:23.621 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 1d+06:16:23.621 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 1d+06:16:23.621 IDENTIFY DEVICE Error 86 [13] occurred at disk power-on lifetime: 12348 hours (514 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 ef ef 45 40 00 Error: UNC at LBA = 0x01efef45 = 32501573 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 38 00 00 01 ef ef 47 40 08 1d+06:16:19.634 READ FPDMA QUEUED 60 00 01 00 30 00 00 01 ef ef 45 40 08 1d+06:16:19.634 READ FPDMA QUEUED 60 00 01 00 28 00 00 01 ef ef 46 40 08 1d+06:16:19.634 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+06:16:19.634 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 1d+06:16:19.634 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 85 [12] occurred at disk power-on lifetime: 12348 hours (514 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 ef ef 44 40 00 Error: UNC at LBA = 0x01efef44 = 32501572 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 a8 00 00 01 ef ef 46 40 08 1d+06:16:15.647 READ FPDMA QUEUED 60 00 01 00 a0 00 00 01 ef ef 45 40 08 1d+06:16:15.647 READ FPDMA QUEUED 60 00 01 00 98 00 00 01 ef ef 44 40 08 1d+06:16:15.646 READ FPDMA QUEUED 60 00 01 00 90 00 00 01 ef ef 47 40 08 1d+06:16:15.646 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+06:16:15.646 SET FEATURES [Enable SATA feature] Error 84 [11] occurred at disk power-on lifetime: 12348 hours (514 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 ef ef 43 40 00 Error: UNC at LBA = 0x01efef43 = 32501571 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 18 00 00 01 ef ef 43 40 08 1d+06:16:11.659 READ FPDMA QUEUED 60 00 01 00 10 00 00 01 ef ef 44 40 08 1d+06:16:11.659 READ FPDMA QUEUED 60 00 01 00 08 00 00 01 ef ef 45 40 08 1d+06:16:11.659 READ FPDMA QUEUED 60 00 01 00 00 00 00 01 ef ef 46 40 08 1d+06:16:11.659 READ FPDMA QUEUED 60 00 01 00 f0 00 00 01 ef ef 47 40 08 1d+06:16:11.659 READ FPDMA QUEUED Error 83 [10] occurred at disk power-on lifetime: 12348 hours (514 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 ef ef 42 40 00 Error: UNC at LBA = 0x01efef42 = 32501570 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 78 00 00 01 ef ef 47 40 08 1d+06:16:07.672 READ FPDMA QUEUED 60 00 01 00 70 00 00 01 ef ef 46 40 08 1d+06:16:07.672 READ FPDMA QUEUED 60 00 01 00 68 00 00 01 ef ef 45 40 08 1d+06:16:07.671 READ FPDMA QUEUED 60 00 01 00 60 00 00 01 ef ef 44 40 08 1d+06:16:07.671 READ FPDMA QUEUED 60 00 01 00 58 00 00 01 ef ef 43 40 08 1d+06:16:07.671 READ FPDMA QUEUED Error 82 [9] occurred at disk power-on lifetime: 12348 hours (514 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 ef ef 41 40 00 Error: UNC at LBA = 0x01efef41 = 32501569 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 d0 00 00 01 ef ef 41 40 08 1d+06:16:03.684 READ FPDMA QUEUED 60 00 01 00 c8 00 00 01 ef ef 42 40 08 1d+06:16:03.684 READ FPDMA QUEUED 60 00 01 00 c0 00 00 01 ef ef 43 40 08 1d+06:16:03.684 READ FPDMA QUEUED 60 00 01 00 b8 00 00 01 ef ef 44 40 08 1d+06:16:03.684 READ FPDMA QUEUED 60 00 01 00 b0 00 00 01 ef ef 45 40 08 1d+06:16:03.684 READ FPDMA QUEUED Error 81 [8] occurred at disk power-on lifetime: 12348 hours (514 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 ef ef 40 40 00 Error: UNC at LBA = 0x01efef40 = 32501568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 38 00 00 01 ef ef 47 40 08 1d+06:15:59.713 READ FPDMA QUEUED 60 00 01 00 30 00 00 01 ef ef 46 40 08 1d+06:15:59.713 READ FPDMA QUEUED 60 00 01 00 28 00 00 01 ef ef 45 40 08 1d+06:15:59.712 READ FPDMA QUEUED 60 00 01 00 20 00 00 01 ef ef 44 40 08 1d+06:15:59.712 READ FPDMA QUEUED 60 00 01 00 18 00 00 01 ef ef 43 40 08 1d+06:15:59.712 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 12524 32501568 # 2 Extended offline Completed: read failure 90% 12519 32501568 # 3 Extended offline Completed: read failure 90% 12356 32501568 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 25/44 Celsius Lifetime Min/Max Temperature: 0/47 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (264) Index Estimated Time Temperature Celsius 265 2016-08-30 13:24 33 ************** ... ..( 43 skipped). .. ************** 309 2016-08-30 14:08 33 ************** 310 2016-08-30 14:09 34 *************** ... ..( 25 skipped). .. *************** 336 2016-08-30 14:35 34 *************** 337 2016-08-30 14:36 32 ************* ... ..( 61 skipped). .. ************* 399 2016-08-30 15:38 32 ************* 400 2016-08-30 15:39 33 ************** ... ..(137 skipped). .. ************** 60 2016-08-30 17:57 33 ************** 61 2016-08-30 17:58 34 *************** ... ..(145 skipped). .. *************** 207 2016-08-30 20:24 34 *************** 208 2016-08-30 20:25 33 ************** ... ..( 55 skipped). .. ************** 264 2016-08-30 21:21 33 ************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 339 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 255 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 1067805 Vendor specific /dev/sdb === START OF INFORMATION SECTION === Model Family: Seagate Momentus 7200.4 Device Model: ST9320423AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0002SDM1 User Capacity: 320 072 933 376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Aug 30 21:21:11 2016 YEKT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 208 (intermediate), recommended: 208 APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 121) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 80) minutes. Conveyance self-test routine recommended polling time: ( 3) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 084 078 006 - 21657642 3 Spin_Up_Time PO---- 100 099 085 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 568 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 078 060 030 - 4371441408 9 Power_On_Hours -O--CK 081 081 000 - 16767 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 817 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 64581 188 Command_Timeout -O--CK 100 089 000 - 38655295751 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 067 054 045 - 33 (Min/Max 24/44) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 2 192 Power-Off_Retract_Count -O--CK 100 100 000 - 209 193 Load_Cycle_Count -O--CK 001 001 000 - 289880 194 Temperature_Celsius -O---K 033 046 000 - 33 (0 7 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 049 043 000 - 21657642 197 Current_Pending_Sector -O--C- 100 100 000 - 170 198 Offline_Uncorrectable ----C- 100 100 000 - 170 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 279 240 Head_Flying_Hours ------ 100 253 000 - 9813 (155 4 0) 241 Total_LBAs_Written ------ 100 253 000 - 3604852499 242 Total_LBAs_Read ------ 100 253 000 - 4151766166 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 52480 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 52480 [19] occurred at disk power-on lifetime: 16765 hours (698 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 11 00 00 88 00 00 Error: UNC at LBA = 0x11000088 = 285212808 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 11 00 00 88 40 00 12d+07:38:36.336 READ FPDMA QUEUED 27 00 00 00 00 00 00 00 00 00 00 e0 00 12d+07:38:36.336 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 12d+07:38:36.335 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 12d+07:38:36.334 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 12d+07:38:36.334 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 52479 [18] occurred at disk power-on lifetime: 16765 hours (698 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 11 00 00 88 00 00 Error: UNC at LBA = 0x11000088 = 285212808 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 11 00 00 88 40 00 12d+07:38:33.617 READ FPDMA QUEUED 60 00 00 00 08 00 00 11 00 00 80 40 00 12d+07:38:33.617 READ FPDMA QUEUED 60 00 00 00 08 00 00 11 00 00 78 40 00 12d+07:38:33.617 READ FPDMA QUEUED 60 00 00 00 08 00 00 11 00 00 70 40 00 12d+07:38:33.617 READ FPDMA QUEUED 60 00 00 00 08 00 00 11 00 00 68 40 00 12d+07:38:33.616 READ FPDMA QUEUED Error 52478 [17] occurred at disk power-on lifetime: 16765 hours (698 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 11 00 00 88 00 00 Error: UNC at LBA = 0x11000088 = 285212808 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 f0 00 00 11 00 00 10 40 00 12d+07:38:30.839 READ FPDMA QUEUED 60 00 00 00 90 00 00 10 00 00 80 40 00 12d+07:38:30.838 READ FPDMA QUEUED 60 00 00 00 38 00 00 10 00 00 40 40 00 12d+07:38:30.838 READ FPDMA QUEUED 60 00 00 00 08 00 00 10 00 00 10 40 00 12d+07:38:30.838 READ FPDMA QUEUED 60 00 00 00 18 00 00 10 00 00 20 40 00 12d+07:38:30.837 READ FPDMA QUEUED Error 52477 [16] occurred at disk power-on lifetime: 16765 hours (698 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 11 00 00 88 00 00 Error: UNC at LBA = 0x11000088 = 285212808 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 11 00 00 88 40 00 12d+07:38:22.607 READ FPDMA QUEUED 27 00 00 00 00 00 00 00 00 00 00 e0 00 12d+07:38:22.606 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 12d+07:38:22.605 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 12d+07:38:22.605 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 12d+07:38:22.604 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 52476 [15] occurred at disk power-on lifetime: 16765 hours (698 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 11 00 00 88 00 00 Error: UNC at LBA = 0x11000088 = 285212808 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 11 00 00 88 40 00 12d+07:38:19.880 READ FPDMA QUEUED 60 00 00 00 08 00 00 11 00 00 80 40 00 12d+07:38:19.879 READ FPDMA QUEUED 60 00 00 00 08 00 00 11 00 00 78 40 00 12d+07:38:19.879 READ FPDMA QUEUED 60 00 00 00 08 00 00 11 00 00 70 40 00 12d+07:38:19.879 READ FPDMA QUEUED 60 00 00 00 08 00 00 11 00 00 68 40 00 12d+07:38:19.878 READ FPDMA QUEUED Error 52475 [14] occurred at disk power-on lifetime: 16765 hours (698 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 11 00 00 88 00 00 Error: UNC at LBA = 0x11000088 = 285212808 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 f0 00 00 11 00 00 10 40 00 12d+07:38:17.106 READ FPDMA QUEUED 60 00 00 00 90 00 00 10 00 00 80 40 00 12d+07:38:17.105 READ FPDMA QUEUED 60 00 00 00 38 00 00 10 00 00 40 40 00 12d+07:38:17.105 READ FPDMA QUEUED 60 00 00 00 08 00 00 10 00 00 10 40 00 12d+07:38:17.105 READ FPDMA QUEUED 60 00 00 00 18 00 00 10 00 00 20 40 00 12d+07:38:17.105 READ FPDMA QUEUED Error 52474 [13] occurred at disk power-on lifetime: 16765 hours (698 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 11 00 00 88 00 00 Error: UNC at LBA = 0x11000088 = 285212808 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 11 00 00 88 40 00 12d+06:56:25.578 READ FPDMA QUEUED 27 00 00 00 00 00 00 00 00 00 00 e0 00 12d+06:56:25.578 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 12d+06:56:25.511 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 12d+06:56:25.511 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 12d+06:56:25.511 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 52473 [12] occurred at disk power-on lifetime: 16765 hours (698 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 11 00 00 88 00 00 Error: UNC at LBA = 0x11000088 = 285212808 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 11 00 00 88 40 00 12d+06:56:22.868 READ FPDMA QUEUED 60 00 00 00 08 00 00 11 00 00 80 40 00 12d+06:56:22.868 READ FPDMA QUEUED 60 00 00 00 08 00 00 11 00 00 78 40 00 12d+06:56:22.867 READ FPDMA QUEUED 60 00 00 00 08 00 00 11 00 00 70 40 00 12d+06:56:22.867 READ FPDMA QUEUED 60 00 00 00 08 00 00 11 00 00 68 40 00 12d+06:56:22.867 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 16676 4488 # 2 Extended offline Completed: read failure 90% 16672 4488 # 3 Extended offline Completed: read failure 90% 16508 4488 # 4 Short offline Completed without error 00% 5308 - # 5 Extended offline Aborted by host 90% 5308 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 24/44 Celsius Lifetime Min/Max Temperature: 7/46 Celsius Lifetime Average Temperature: 33 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (107) Index Estimated Time Temperature Celsius 108 2016-08-30 19:14 33 ************** ... ..( 34 skipped). .. ************** 15 2016-08-30 19:49 33 ************** 16 2016-08-30 19:50 32 ************* ... ..( 4 skipped). .. ************* 21 2016-08-30 19:55 32 ************* 22 2016-08-30 19:56 33 ************** ... ..( 59 skipped). .. ************** 82 2016-08-30 20:56 33 ************** 83 2016-08-30 20:57 34 *************** ... ..( 17 skipped). .. *************** 101 2016-08-30 21:15 34 *************** 102 2016-08-30 21:16 33 ************** ... ..( 4 skipped). .. ************** 107 2016-08-30 21:21 33 ************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 251 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdc === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K1000.C Device Model: Hitachi HDS721010CLA332 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: JP4OA3EA User Capacity: 1 000 204 886 016 bytes [1,00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Aug 30 21:21:11 2016 YEKT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (10399) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 173) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 134 134 054 - 100 3 Spin_Up_Time POS--- 123 123 024 - 299 (Average 315) 4 Start_Stop_Count -O--C- 100 100 000 - 531 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 3 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 140 140 020 - 30 9 Power_On_Hours -O--C- 093 093 000 - 50489 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 511 192 Power-Off_Retract_Count -O--CK 100 100 000 - 713 193 Load_Cycle_Count -O--C- 100 100 000 - 713 194 Temperature_Celsius -O---- 166 166 000 - 36 (Min/Max 13/55) 196 Reallocated_Event_Count -O--CK 100 100 000 - 3 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 2 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 5108 hours (212 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 43 00 00 05 81 23 c4 05 00 Error: ICRC, ABRT 67 sectors at LBA = 0x058123c4 = 92349380 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 05 81 23 87 e5 08 6d+15:06:27.893 WRITE DMA EXT 35 00 00 00 80 00 00 05 81 23 07 e5 08 6d+15:06:27.891 WRITE DMA EXT 35 00 00 00 08 00 00 05 81 22 ff e5 08 6d+15:06:27.889 WRITE DMA EXT 35 00 00 00 10 00 00 05 81 22 ef e5 08 6d+15:06:27.887 WRITE DMA EXT 35 00 00 00 10 00 00 05 81 22 df e5 08 6d+15:06:27.886 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 50402 - # 2 Extended offline Interrupted (host reset) 30% 50396 - # 3 Extended offline Completed without error 00% 50234 - # 4 Extended offline Aborted by host 90% 39111 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 27/44 Celsius Lifetime Min/Max Temperature: 13/55 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (2) Index Estimated Time Temperature Celsius 3 2016-08-30 19:14 36 ***************** ... ..( 13 skipped). .. ***************** 17 2016-08-30 19:28 36 ***************** 18 2016-08-30 19:29 37 ****************** ... ..( 3 skipped). .. ****************** 22 2016-08-30 19:33 37 ****************** 23 2016-08-30 19:34 36 ***************** ... ..( 13 skipped). .. ***************** 37 2016-08-30 19:48 36 ***************** 38 2016-08-30 19:49 37 ****************** ... ..( 2 skipped). .. ****************** 41 2016-08-30 19:52 37 ****************** 42 2016-08-30 19:53 36 ***************** ... ..( 15 skipped). .. ***************** 58 2016-08-30 20:09 36 ***************** 59 2016-08-30 20:10 37 ****************** ... ..( 5 skipped). .. ****************** 65 2016-08-30 20:16 37 ****************** 66 2016-08-30 20:17 36 ***************** ... ..( 12 skipped). .. ***************** 79 2016-08-30 20:30 36 ***************** 80 2016-08-30 20:31 37 ****************** ... ..( 3 skipped). .. ****************** 84 2016-08-30 20:35 37 ****************** 85 2016-08-30 20:36 36 ***************** ... ..( 13 skipped). .. ***************** 99 2016-08-30 20:50 36 ***************** 100 2016-08-30 20:51 37 ****************** ... ..( 4 skipped). .. ****************** 105 2016-08-30 20:56 37 ****************** 106 2016-08-30 20:57 36 ***************** ... ..( 12 skipped). .. ***************** 119 2016-08-30 21:10 36 ***************** 120 2016-08-30 21:11 37 ****************** ... ..( 5 skipped). .. ****************** 126 2016-08-30 21:17 37 ****************** 127 2016-08-30 21:18 36 ***************** ... ..( 2 skipped). .. ***************** 2 2016-08-30 21:21 36 ***************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 511 --- Lifetime Power-On Resets 0x01 0x010 4 50489 --- Power-on Hours 0x01 0x018 6 93963190003 --- Logical Sectors Written 0x01 0x020 6 1147126310 --- Number of Write Commands 0x01 0x028 6 977311380135 --- Logical Sectors Read 0x01 0x030 6 2006615970 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 50471 --- Spindle Motor Power-on Hours 0x03 0x010 4 50471 --- Head Flying Hours 0x03 0x018 4 713 --- Head Load Events 0x03 0x020 4 3 --- Number of Reallocated Logical Sectors 0x03 0x028 4 1596 --- Read Recovery Attempts 0x03 0x030 4 2 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 1248 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 36 --- Current Temperature 0x05 0x010 1 34 N-- Average Short Term Temperature 0x05 0x018 1 36 N-- Average Long Term Temperature 0x05 0x020 1 55 --- Highest Temperature 0x05 0x028 1 13 --- Lowest Temperature 0x05 0x030 1 49 N-- Highest Average Short Term Temperature 0x05 0x038 1 0 N-- Lowest Average Short Term Temperature 0x05 0x040 1 46 N-- Highest Average Long Term Temperature 0x05 0x048 1 0 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 3279 --- Number of Hardware Resets 0x06 0x010 4 2251 --- Number of ASR Events 0x06 0x018 4 2 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0009 2 341 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 250 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS