/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.19.0-46-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" DT01ACA... Desktop HDD Device Model: TOSHIBA DT01ACA100 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: MS2OA800 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Aug 12 15:58:19 2023 CAT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7167) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 120) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 078 016 - 0 2 Throughput_Performance POS--K 142 100 054 - 71 3 Spin_Up_Time PO---K 127 100 024 - 182 (Average 180) 4 Start_Stop_Count -O--CK 100 100 000 - 1966 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate POSR-K 100 100 067 - 0 8 Seek_Time_Performance P-S--K 118 100 020 - 33 9 Power_On_Hours -O--CK 099 099 000 - 12280 10 Spin_Retry_Count PO--CK 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 1916 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 185 Unknown_Attribute -O--CK 042 042 000 - 3866623 187 Reported_Uncorrect -O--CK 099 099 000 - 393217 188 Command_Timeout -O--CK 100 099 000 - 4295688300 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 064 053 000 - 36 (Min/Max 26/36) 192 Power-Off_Retract_Count -O--CK 099 099 000 - 1970 193 Load_Cycle_Count -O--CK 099 099 000 - 1970 194 Temperature_Celsius -O---K 166 127 000 - 36 (Min/Max 14/47) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 12 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 13 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 13 [0] occurred at disk power-on lifetime: 10580 hours (440 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 30 00 00 00 65 82 78 00 00 Error: IDNF at LBA = 0x00658278 = 6652536 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 30 00 38 00 00 00 65 82 78 40 00 00:02:26.036 WRITE FPDMA QUEUED 61 00 08 00 30 00 00 00 65 81 90 40 00 00:02:26.036 WRITE FPDMA QUEUED 61 00 08 00 28 00 00 00 65 81 50 40 00 00:02:26.036 WRITE FPDMA QUEUED 61 00 08 00 20 00 00 00 65 81 38 40 00 00:02:26.035 WRITE FPDMA QUEUED 61 00 08 00 18 00 00 00 65 81 18 40 00 00:02:26.035 WRITE FPDMA QUEUED Error 12 [3] occurred at disk power-on lifetime: 10548 hours (439 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 b1 00 00 02 4b c1 0f 02 00 Error: ICRC, ABRT at LBA = 0x024bc10f = 38519055 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 b0 00 00 02 4b c1 10 42 ff 00:03:10.162 READ FPDMA QUEUED 60 01 00 00 80 00 00 02 4b c0 c0 40 00 00:03:10.161 READ FPDMA QUEUED 60 01 00 00 78 00 00 02 4b bf c0 40 00 00:03:10.161 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:03:10.134 FLUSH CACHE EXT 60 01 00 00 68 00 00 02 4b ba c0 40 00 00:03:10.133 READ FPDMA QUEUED Error 11 [2] occurred at disk power-on lifetime: 10548 hours (439 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 71 00 00 00 46 97 9f 00 00 Error: ICRC, ABRT at LBA = 0x0046979f = 4626335 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 b0 00 00 00 46 97 90 40 00 00:01:57.155 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 a0 00 00:01:56.663 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:01:56.663 SET FEATURES [Enable write cache] ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:01:56.662 SET FEATURES [Enable write cache] 2f 00 00 00 00 00 00 00 00 00 00 e0 ff 00:01:56.643 READ LOG EXT Error 10 [1] occurred at disk power-on lifetime: 10548 hours (439 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 11 00 00 00 b5 a9 23 00 00 Error: ICRC, ABRT at LBA = 0x00b5a923 = 11905315 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 a8 00 00 00 b5 a9 14 40 00 00:01:56.630 READ FPDMA QUEUED 60 00 01 00 a0 00 00 00 77 20 8f 40 00 00:01:56.616 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 a0 00 00:01:56.137 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:01:56.137 SET FEATURES [Enable write cache] ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:01:56.137 SET FEATURES [Enable write cache] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 26/36 Celsius Lifetime Min/Max Temperature: 14/47 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (98) Index Estimated Time Temperature Celsius 99 2023-08-12 13:51 32 ************* ... ..( 5 skipped). .. ************* 105 2023-08-12 13:57 32 ************* 106 2023-08-12 13:58 31 ************ ... ..( 7 skipped). .. ************ 114 2023-08-12 14:06 31 ************ 115 2023-08-12 14:07 32 ************* ... ..( 4 skipped). .. ************* 120 2023-08-12 14:12 32 ************* 121 2023-08-12 14:13 31 ************ 122 2023-08-12 14:14 32 ************* 123 2023-08-12 14:15 32 ************* 124 2023-08-12 14:16 31 ************ ... ..( 15 skipped). .. ************ 12 2023-08-12 14:32 31 ************ 13 2023-08-12 14:33 30 *********** ... ..( 9 skipped). .. *********** 23 2023-08-12 14:43 30 *********** 24 2023-08-12 14:44 31 ************ ... ..( 2 skipped). .. ************ 27 2023-08-12 14:47 31 ************ 28 2023-08-12 14:48 30 *********** 29 2023-08-12 14:49 31 ************ 30 2023-08-12 14:50 30 *********** ... ..( 17 skipped). .. *********** 48 2023-08-12 15:08 30 *********** 49 2023-08-12 15:09 ? - 50 2023-08-12 15:10 27 ******** 51 2023-08-12 15:11 28 ********* 52 2023-08-12 15:12 28 ********* 53 2023-08-12 15:13 29 ********** 54 2023-08-12 15:14 29 ********** 55 2023-08-12 15:15 30 *********** 56 2023-08-12 15:16 30 *********** 57 2023-08-12 15:17 31 ************ 58 2023-08-12 15:18 31 ************ 59 2023-08-12 15:19 32 ************* ... ..( 2 skipped). .. ************* 62 2023-08-12 15:22 32 ************* 63 2023-08-12 15:23 33 ************** ... ..( 2 skipped). .. ************** 66 2023-08-12 15:26 33 ************** 67 2023-08-12 15:27 34 *************** ... ..( 3 skipped). .. *************** 71 2023-08-12 15:31 34 *************** 72 2023-08-12 15:32 35 **************** ... ..( 7 skipped). .. **************** 80 2023-08-12 15:40 35 **************** 81 2023-08-12 15:41 36 ***************** 82 2023-08-12 15:42 35 **************** 83 2023-08-12 15:43 36 ***************** ... ..( 14 skipped). .. ***************** 98 2023-08-12 15:58 36 ***************** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1916 --- Lifetime Power-On Resets 0x01 0x010 4 12280 --- Power-on Hours 0x01 0x018 6 42552608732 --- Logical Sectors Written 0x01 0x020 6 485891332 --- Number of Write Commands 0x01 0x028 6 77670295825 --- Logical Sectors Read 0x01 0x030 6 577712912 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 12246 --- Spindle Motor Power-on Hours 0x03 0x010 4 12246 --- Head Flying Hours 0x03 0x018 4 1970 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 549 --- Read Recovery Attempts 0x03 0x030 4 2 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 1 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 108 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 36 --- Current Temperature 0x05 0x010 1 32 N-- Average Short Term Temperature 0x05 0x018 1 31 N-- Average Long Term Temperature 0x05 0x020 1 47 --- Highest Temperature 0x05 0x028 1 14 --- Lowest Temperature 0x05 0x030 1 43 N-- Highest Average Short Term Temperature 0x05 0x038 1 20 N-- Lowest Average Short Term Temperature 0x05 0x040 1 41 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 7577 --- Number of Hardware Resets 0x06 0x010 4 4864 --- Number of ASR Events 0x06 0x018 4 12 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS