/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.1-desktop-1omv2290] (OpenMandriva Lx 7.3-2) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar SE Serial ATA Device Model: WDC WD800JD-60JRA0 Serial Number: -- Firmware Version: 05.01C05 User Capacity: 80,026,361,856 bytes [80.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Wed Jan 11 18:38:59 2023 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Unavailable Unknown SCT Status format version 1, should be 2 or 3. Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2460) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 35) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x001f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 14 3 Spin_Up_Time PO---- 165 163 021 - 2750 4 Start_Stop_Count -O--CK 097 097 000 - 3518 5 Reallocated_Sector_Ct PO--CK 199 199 140 - 1 7 Seek_Error_Rate POSR-- 200 200 051 - 0 9 Power_On_Hours -O--CK 078 078 000 - 16138 10 Spin_Retry_Count PO--C- 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3418 194 Temperature_Celsius -O---K 123 091 000 - 20 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 722 200 Multi_Zone_Error_Rate P--R-- 200 200 051 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning Read SMART Log Directory failed: scsi error badly formed scsi parameters General Purpose Log Directory not supported SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 Warning: ATA error count 7 inconsistent with error log pointer 5 ATA Error Count: 7 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 7 occurred at disk power-on lifetime: 15674 hours (653 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 cb 15 70 45 e4 Error: UNC 203 sectors at LBA = 0x04457015 = 71659541 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 f0 f0 6f 45 04 68 00:27:21.280 READ DMA c8 00 08 e8 6f 45 04 68 00:27:21.280 READ DMA c8 00 08 e0 6f 45 04 68 00:27:21.280 READ DMA c8 00 f8 b0 6e 45 04 68 00:27:21.280 READ DMA c8 00 08 a8 6e 45 04 68 00:27:21.280 READ DMA Error 6 occurred at disk power-on lifetime: 15674 hours (653 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 cb 15 70 45 e4 Error: UNC 203 sectors at LBA = 0x04457015 = 71659541 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 f0 f0 6f 45 04 68 00:21:31.195 READ DMA c8 00 08 e8 6f 45 04 68 00:21:31.195 READ DMA c8 00 08 e0 6f 45 04 68 00:21:31.195 READ DMA c8 00 f8 b0 6e 45 04 68 00:21:31.195 READ DMA c8 00 08 a8 6e 45 04 68 00:21:31.195 READ DMA Error 5 occurred at disk power-on lifetime: 15674 hours (653 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 cb 15 70 45 e4 Error: UNC 203 sectors at LBA = 0x04457015 = 71659541 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 f0 f0 6f 45 04 68 00:21:23.805 READ DMA c8 00 08 e8 6f 45 04 68 00:21:23.805 READ DMA c8 00 08 e0 6f 45 04 68 00:21:23.805 READ DMA c8 00 f8 b0 6e 45 04 68 00:21:23.800 READ DMA c8 00 08 a8 6e 45 04 68 00:21:23.800 READ DMA Error 4 occurred at disk power-on lifetime: 15674 hours (653 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 cb 15 70 45 e4 Error: UNC 203 sectors at LBA = 0x04457015 = 71659541 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 f0 f0 6f 45 04 68 00:18:39.855 READ DMA c8 00 08 e8 6f 45 04 68 00:18:39.855 READ DMA c8 00 08 e0 6f 45 04 68 00:18:39.855 READ DMA c8 00 f8 b0 6e 45 04 68 00:18:39.850 READ DMA c8 00 08 a8 6e 45 04 68 00:18:39.845 READ DMA Error 3 occurred at disk power-on lifetime: 15674 hours (653 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 cb 15 70 45 e4 Error: UNC 203 sectors at LBA = 0x04457015 = 71659541 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 f0 f0 6f 45 04 68 00:10:51.450 READ DMA c8 00 08 e8 6f 45 04 68 00:10:51.450 READ DMA c8 00 08 e0 6f 45 04 68 00:10:51.445 READ DMA c8 00 f8 b0 6e 45 04 68 00:10:51.445 READ DMA c8 00 08 a8 6e 45 04 68 00:10:51.445 READ DMA SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Unknown SCT Status format version 1, should be 2 or 3. Unknown SCT Status format version 1, should be 2 or 3. SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported