/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.32-generic-2rosa-x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: Apacer AS350 256GB Serial Number: -- LU WWN Device Id: 5 dc6630 ... Firmware Version: AP613PE0 User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Mar 17 19:47:38 2021 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 9 Power_On_Hours -O--CK 100 100 000 - 411 12 Power_Cycle_Count -O--CK 100 100 000 - 136 163 Unknown_Attribute -O--CK 100 100 000 - 5 164 Unknown_Attribute -O--CK 100 100 000 - 3 166 Unknown_Attribute -O--CK 100 100 000 - 0 167 Unknown_Attribute -O--CK 100 100 000 - 0 168 Unknown_Attribute -O--CK 100 100 000 - 0 171 Unknown_Attribute -O--CK 100 100 000 - 0 172 Unknown_Attribute -O--CK 100 100 000 - 0 175 Program_Fail_Count_Chip -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 8 194 Temperature_Celsius -O---K 067 067 058 - 33 (Min/Max 33/33) 231 Temperature_Celsius -O--C- 100 100 000 - 99 241 Total_LBAs_Written -O--CK 100 100 000 - 2079047256 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 136 --- Lifetime Power-On Resets 0x01 0x010 4 411 --- Power-on Hours 0x01 0x018 6 2079047256 --- Logical Sectors Written 0x01 0x028 6 774578224 --- Logical Sectors Read 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 33 --- Current Temperature 0x05 0x020 1 33 --- Highest Temperature 0x05 0x028 1 33 --- Lowest Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 515 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 3 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.32-generic-2rosa-x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD10EZEX-00BN5A0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Mar 17 19:47:38 2021 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11280) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 117) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 175 173 021 - 2208 4 Start_Stop_Count -O--CK 091 091 000 - 9730 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 071 071 000 - 21186 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 5469 192 Power-Off_Retract_Count -O--CK 200 200 000 - 252 193 Load_Cycle_Count -O--CK 197 197 000 - 9483 194 Temperature_Celsius -O---K 112 098 000 - 31 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 12 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 12 [11] occurred at disk power-on lifetime: 8282 hours (345 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 c2 4f 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:41.163 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:39.049 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:36.934 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:34.820 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:32.705 SMART ENABLE OPERATIONS Error 11 [10] occurred at disk power-on lifetime: 8282 hours (345 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 c2 4f 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:39.049 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:36.934 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:34.820 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:32.705 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:30.590 SMART ENABLE OPERATIONS Error 10 [9] occurred at disk power-on lifetime: 8282 hours (345 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 c2 4f 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:36.934 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:34.820 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:32.705 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:30.590 SMART ENABLE OPERATIONS b0 00 da 00 00 00 00 00 c2 4f 00 40 00 00:00:28.468 SMART RETURN STATUS Error 9 [8] occurred at disk power-on lifetime: 8282 hours (345 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 c2 4f 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:34.820 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:32.705 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:30.590 SMART ENABLE OPERATIONS b0 00 da 00 00 00 00 00 c2 4f 00 40 00 00:00:28.468 SMART RETURN STATUS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:26.353 SMART ENABLE OPERATIONS Error 8 [7] occurred at disk power-on lifetime: 8282 hours (345 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 c2 4f 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:32.705 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:30.590 SMART ENABLE OPERATIONS b0 00 da 00 00 00 00 00 c2 4f 00 40 00 00:00:28.468 SMART RETURN STATUS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:26.353 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:24.239 SMART ENABLE OPERATIONS Error 7 [6] occurred at disk power-on lifetime: 8282 hours (345 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 c2 4f 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:30.590 SMART ENABLE OPERATIONS b0 00 da 00 00 00 00 00 c2 4f 00 40 00 00:00:28.468 SMART RETURN STATUS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:26.353 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:24.239 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:22.124 SMART ENABLE OPERATIONS Error 6 [5] occurred at disk power-on lifetime: 8282 hours (345 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 c2 4f 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:26.353 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:24.239 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:22.124 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:20.010 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:17.895 SMART ENABLE OPERATIONS Error 5 [4] occurred at disk power-on lifetime: 8282 hours (345 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 c2 4f 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:24.239 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:22.124 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:20.010 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:17.895 SMART ENABLE OPERATIONS b0 00 d8 00 00 00 00 00 c2 4f 00 40 00 00:00:15.772 SMART ENABLE OPERATIONS SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 31/31 Celsius Lifetime Min/Max Temperature: 17/46 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (357) Index Estimated Time Temperature Celsius 358 2021-03-17 11:50 29 ********** ... ..( 15 skipped). .. ********** 374 2021-03-17 12:06 29 ********** 375 2021-03-17 12:07 ? - 376 2021-03-17 12:08 23 **** 377 2021-03-17 12:09 23 **** 378 2021-03-17 12:10 23 **** 379 2021-03-17 12:11 24 ***** 380 2021-03-17 12:12 25 ****** 381 2021-03-17 12:13 25 ****** 382 2021-03-17 12:14 26 ******* 383 2021-03-17 12:15 26 ******* 384 2021-03-17 12:16 26 ******* 385 2021-03-17 12:17 27 ******** 386 2021-03-17 12:18 27 ******** 387 2021-03-17 12:19 27 ******** 388 2021-03-17 12:20 28 ********* ... ..( 2 skipped). .. ********* 391 2021-03-17 12:23 28 ********* 392 2021-03-17 12:24 29 ********** ... ..( 11 skipped). .. ********** 404 2021-03-17 12:36 29 ********** 405 2021-03-17 12:37 30 *********** ... ..( 89 skipped). .. *********** 17 2021-03-17 14:07 30 *********** 18 2021-03-17 14:08 31 ************ ... ..( 90 skipped). .. ************ 109 2021-03-17 15:39 31 ************ 110 2021-03-17 15:40 ? - 111 2021-03-17 15:41 29 ********** ... ..( 15 skipped). .. ********** 127 2021-03-17 15:57 29 ********** 128 2021-03-17 15:58 30 *********** ... ..( 54 skipped). .. *********** 183 2021-03-17 16:53 30 *********** 184 2021-03-17 16:54 31 ************ 185 2021-03-17 16:55 30 *********** 186 2021-03-17 16:56 30 *********** 187 2021-03-17 16:57 30 *********** 188 2021-03-17 16:58 29 ********** 189 2021-03-17 16:59 29 ********** 190 2021-03-17 17:00 29 ********** 191 2021-03-17 17:01 28 ********* 192 2021-03-17 17:02 ? - 193 2021-03-17 17:03 28 ********* ... ..( 5 skipped). .. ********* 199 2021-03-17 17:09 28 ********* 200 2021-03-17 17:10 29 ********** ... ..( 10 skipped). .. ********** 211 2021-03-17 17:21 29 ********** 212 2021-03-17 17:22 30 *********** ... ..( 63 skipped). .. *********** 276 2021-03-17 18:26 30 *********** 277 2021-03-17 18:27 ? - 278 2021-03-17 18:28 30 *********** ... ..( 39 skipped). .. *********** 318 2021-03-17 19:08 30 *********** 319 2021-03-17 19:09 ? - 320 2021-03-17 19:10 31 ************ ... ..( 10 skipped). .. ************ 331 2021-03-17 19:21 31 ************ 332 2021-03-17 19:22 ? - 333 2021-03-17 19:23 31 ************ ... ..( 2 skipped). .. ************ 336 2021-03-17 19:26 31 ************ 337 2021-03-17 19:27 ? - 338 2021-03-17 19:28 31 ************ ... ..( 7 skipped). .. ************ 346 2021-03-17 19:36 31 ************ 347 2021-03-17 19:37 ? - 348 2021-03-17 19:38 31 ************ ... ..( 2 skipped). .. ************ 351 2021-03-17 19:41 31 ************ 352 2021-03-17 19:42 29 ********** ... ..( 4 skipped). .. ********** 357 2021-03-17 19:47 29 ********** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 219 Vendor specific /dev/sdc smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.32-generic-2rosa-x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: WD Blue and Green SSDs Device Model: WDC WDS240G2G0B-00EPW0 Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: UJ450000 User Capacity: 240,065,183,744 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: M.2 Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Mar 17 19:47:38 2021 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 32) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x15) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 42) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 5618 12 Power_Cycle_Count -O--CK 100 100 000 - 1999 165 Block_Erase_Count -O--CK 100 100 000 - 3982 166 Minimum_PE_Cycles_TLC -O--CK 100 100 --- - 24 167 Max_Bad_Blocks_per_Die -O--CK 100 100 --- - 0 168 Maximum_PE_Cycles_TLC -O--CK 100 100 --- - 37 169 Total_Bad_Blocks -O--CK 100 100 --- - 391 170 Grown_Bad_Blocks -O--CK 100 100 --- - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Average_PE_Cycles_TLC -O--CK 100 100 000 - 24 174 Unexpected_Power_Loss -O--CK 100 100 000 - 73 184 End-to-End_Error -O--CK 100 100 --- - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 --- - 0 194 Temperature_Celsius -O---K 072 048 000 - 28 (Min/Max 10/48) 199 UDMA_CRC_Error_Count -O--CK 100 100 --- - 0 230 Media_Wearout_Indicator -O--CK 100 100 000 - 0x0b2504500b25 232 Available_Reservd_Space PO--CK 100 100 005 - 100 233 NAND_GB_Written_TLC -O--CK 100 100 --- - 6013 234 NAND_GB_Written_SLC -O--CK 100 100 000 - 30365 241 Host_Writes_GiB ----CK 100 100 000 - 11667 242 Host_Reads_GiB ----CK 100 100 000 - 12645 244 Temp_Throttle_Status -O--CK 000 100 --- - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3 GPL,SL VS 1 Device vendor specific log 0xa7 GPL,SL VS 1 Device vendor specific log 0xa9 GPL,SL VS 3 Device vendor specific log Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1999 --- Lifetime Power-On Resets 0x01 0x010 4 5618 --- Power-on Hours 0x01 0x018 6 24468398221 --- Logical Sectors Written 0x01 0x028 6 26519143801 --- Logical Sectors Read 0x01 0x038 6 5618 --- Date and Time TimeStamp 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 28 --- Current Temperature 0x05 0x010 1 - --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 48 --- Highest Temperature 0x05 0x028 1 23 --- Lowest Temperature 0x05 0x030 1 - --- Highest Average Short Term Temperature 0x05 0x038 1 - --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 95 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 4 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0001 2 0 Command failed due to ICRC error