/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.14-desktop-1omv4002] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8 (AF) Device Model: ST320LM001 HN-M320MBB Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 2AR10002 User Capacity: 320,072,933,376 bytes [320 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Fri Jun 4 03:08:50 2021 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 254 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 5220) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 87) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 3259 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 091 026 025 - 2870 4 Start_Stop_Count -O--CK 097 097 000 - 3091 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 5336 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 78 12 Power_Cycle_Count -O--CK 097 097 000 - 3108 191 G-Sense_Error_Rate -O---K 099 099 000 - 10790 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 048 000 - 29 (Min/Max 14/52) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 100 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 5 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 18604 223 Load_Retry_Count -O--CK 100 100 000 - 78 225 Load_Cycle_Count -O--CK 096 096 000 - 47649 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 3109 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3109 [4] occurred at disk power-on lifetime: 5198 hours (216 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 c2 4f 00 a0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d0 00 01 00 00 00 c2 4f 00 a0 00 00:00:01.757 SMART READ DATA ec 00 00 00 01 00 00 00 00 00 00 a0 00 00:00:01.757 IDENTIFY DEVICE 25 00 00 00 08 00 00 00 60 00 20 e0 00 00:00:01.756 READ DMA EXT 25 00 00 00 08 00 00 00 60 00 18 e0 00 00:00:01.756 READ DMA EXT 25 00 00 00 08 00 00 00 00 00 08 e0 00 00:00:01.756 READ DMA EXT Error 3108 [3] occurred at disk power-on lifetime: 5198 hours (216 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 c2 4f 00 a0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d0 00 01 00 00 00 c2 4f 00 a0 00 00:00:01.559 SMART READ DATA ec 00 00 00 01 00 00 00 00 00 00 a0 00 00:00:01.559 IDENTIFY DEVICE 25 00 00 00 08 00 00 00 60 00 18 e0 00 00:00:01.559 READ DMA EXT 25 00 00 00 08 00 00 25 42 ea 00 e0 00 00:00:01.559 READ DMA EXT 25 00 00 00 08 00 00 25 42 ea a0 e0 00 00:00:01.559 READ DMA EXT Error 3107 [2] occurred at disk power-on lifetime: 5192 hours (216 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 08 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 8 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:00.071 READ DMA EXT ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:00.065 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:00.065 IDENTIFY DEVICE ef 00 03 00 08 00 00 00 00 00 00 a0 00 00:00:00.059 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:00.059 IDENTIFY DEVICE Error 3106 [1] occurred at disk power-on lifetime: 5192 hours (216 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:00.018 IDENTIFY DEVICE 00 00 00 00 01 00 00 00 00 00 01 00 00 00:00:00.018 NOP [Abort queued commands] 00 00 00 00 01 00 00 00 00 00 01 00 00 00:00:00.017 NOP [Abort queued commands] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:00.011 IDENTIFY DEVICE a1 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:00.004 IDENTIFY PACKET DEVICE Error 3105 [0] occurred at disk power-on lifetime: 3753 hours (156 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 08 00 00 07 9e 0d 80 40 00 Error: ICRC, ABRT at LBA = 0x079e0d80 = 127798656 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 07 9e 0d 80 40 00 00:00:00.560 WRITE FPDMA QUEUED 61 00 00 00 30 00 00 08 e9 a2 38 40 00 00:00:00.560 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 08 e9 9c a8 40 00 00:00:00.560 WRITE FPDMA QUEUED 61 00 00 00 20 00 00 07 9e 0d 88 40 00 00:00:00.560 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 07 9e 0d 80 40 00 00:00:00.560 WRITE FPDMA QUEUED Error 3104 [7] occurred at disk power-on lifetime: 1187 hours (49 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 03 df 2b 5f e0 00 Error: UNC 1 sectors at LBA = 0x03df2b5f = 64957279 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 03 df 2b 5f e0 00 00:00:05.474 READ DMA EXT 35 00 00 00 40 00 00 02 6a 9c 80 e0 00 00:00:05.473 WRITE DMA EXT 25 00 00 00 01 00 00 03 df 2b 5e e0 00 00:00:05.472 READ DMA EXT 25 00 00 00 01 00 00 03 df 2b 5d e0 00 00:00:05.470 READ DMA EXT 25 00 00 00 68 00 00 05 3c ba 80 e0 00 00:00:05.470 READ DMA EXT Error 3103 [6] occurred at disk power-on lifetime: 1187 hours (49 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 03 df 2b 5e e0 00 Error: UNC 1 sectors at LBA = 0x03df2b5e = 64957278 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 03 df 2b 5e e0 00 00:00:05.472 READ DMA EXT 25 00 00 00 01 00 00 03 df 2b 5d e0 00 00:00:05.470 READ DMA EXT 25 00 00 00 68 00 00 05 3c ba 80 e0 00 00:00:05.470 READ DMA EXT 35 00 00 00 08 00 00 00 6c 42 68 e0 00 00:00:05.470 WRITE DMA EXT 25 00 00 00 80 00 00 05 36 6e 48 e0 00 00:00:05.470 READ DMA EXT Error 3102 [5] occurred at disk power-on lifetime: 1187 hours (49 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 03 df 2b 5d e0 00 Error: UNC 1 sectors at LBA = 0x03df2b5d = 64957277 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 03 df 2b 5d e0 00 00:00:05.470 READ DMA EXT 25 00 00 00 68 00 00 05 3c ba 80 e0 00 00:00:05.470 READ DMA EXT 35 00 00 00 08 00 00 00 6c 42 68 e0 00 00:00:05.470 WRITE DMA EXT 25 00 00 00 80 00 00 05 36 6e 48 e0 00 00:00:05.470 READ DMA EXT ea 00 00 00 00 6c 42 7f 00 00 00 e0 00 00:00:05.470 FLUSH CACHE EXT SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5258 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 29/30 Celsius Lifetime Min/Max Temperature: 14/52 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (19) Index Estimated Time Temperature Celsius 20 2021-06-03 16:30 30 *********** 21 2021-06-03 16:35 33 ************** ... ..( 5 skipped). .. ************** 27 2021-06-03 17:05 33 ************** 28 2021-06-03 17:10 34 *************** 29 2021-06-03 17:15 34 *************** 30 2021-06-03 17:20 34 *************** 31 2021-06-03 17:25 33 ************** ... ..( 6 skipped). .. ************** 38 2021-06-03 18:00 33 ************** 39 2021-06-03 18:05 34 *************** ... ..( 3 skipped). .. *************** 43 2021-06-03 18:25 34 *************** 44 2021-06-03 18:30 33 ************** ... ..( 10 skipped). .. ************** 55 2021-06-03 19:25 33 ************** 56 2021-06-03 19:30 25 ****** 57 2021-06-03 19:35 27 ******** 58 2021-06-03 19:40 28 ********* 59 2021-06-03 19:45 29 ********** 60 2021-06-03 19:50 30 *********** 61 2021-06-03 19:55 29 ********** 62 2021-06-03 20:00 29 ********** 63 2021-06-03 20:05 30 *********** 64 2021-06-03 20:10 30 *********** 65 2021-06-03 20:15 31 ************ ... ..( 11 skipped). .. ************ 77 2021-06-03 21:15 31 ************ 78 2021-06-03 21:20 24 ***** 79 2021-06-03 21:25 28 ********* 80 2021-06-03 21:30 30 *********** 81 2021-06-03 21:35 31 ************ 82 2021-06-03 21:40 30 *********** 83 2021-06-03 21:45 31 ************ ... ..( 8 skipped). .. ************ 92 2021-06-03 22:30 31 ************ 93 2021-06-03 22:35 32 ************* ... ..( 16 skipped). .. ************* 110 2021-06-04 00:00 32 ************* 111 2021-06-04 00:05 33 ************** 112 2021-06-04 00:10 33 ************** 113 2021-06-04 00:15 32 ************* ... ..( 4 skipped). .. ************* 118 2021-06-04 00:40 32 ************* 119 2021-06-04 00:45 25 ****** 120 2021-06-04 00:50 27 ******** 121 2021-06-04 00:55 29 ********** 122 2021-06-04 01:00 30 *********** 123 2021-06-04 01:05 30 *********** 124 2021-06-04 01:10 29 ********** 125 2021-06-04 01:15 31 ************ ... ..( 3 skipped). .. ************ 1 2021-06-04 01:35 31 ************ 2 2021-06-04 01:40 32 ************* ... ..( 6 skipped). .. ************* 9 2021-06-04 02:15 32 ************* 10 2021-06-04 02:20 31 ************ 11 2021-06-04 02:25 32 ************* ... ..( 6 skipped). .. ************* 18 2021-06-04 03:00 32 ************* 19 2021-06-04 03:05 30 *********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 1 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.14-desktop-1omv4002] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint S250 Device Model: SAMSUNG HD250HJ Serial Number: -- LU WWN Device Id: 5 0000f0 ... Firmware Version: FH100-06 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b Local Time is: Fri Jun 4 03:08:50 2021 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 254 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3569) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 60) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 253 100 051 - 0 3 Spin_Up_Time POS--- 253 253 025 - 4288 4 Start_Stop_Count -O--CK 092 092 000 - 8972 5 Reallocated_Sector_Ct PO--CK 253 253 010 - 0 7 Seek_Error_Rate POSR-- 253 253 051 - 0 8 Seek_Time_Performance P-S--K 253 253 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 8461 10 Spin_Retry_Count PO--CK 253 253 051 - 0 11 Calibration_Retry_Count -O--C- 253 253 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4685 13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 5970 184 End-to-End_Error PO--CK 253 253 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 14092322 188 Command_Timeout -O--CK 253 253 000 - 0 190 Airflow_Temperature_Cel -O---K 151 088 000 - 29 (Min/Max 10/50) 194 Temperature_Celsius -O---K 148 088 000 - 30 (Min/Max 10/50) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 5970 196 Reallocated_Event_Count -O--CK 253 253 000 - 0 197 Current_Pending_Sector -O--C- 253 098 000 - 0 198 Offline_Uncorrectable ----CK 253 253 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 6 200 Multi_Zone_Error_Rate -O-R-- 253 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 098 000 - 0 202 Data_Address_Mark_Errs -O--CK 253 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 2128 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2128 [7] occurred at disk power-on lifetime: 8849 hours (368 days + 17 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 08 -- 00 00 00 e0 00 00 00 00 00 c8 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 45 00 00 00 00 27 00 00 e0 00 00 00 00 00:00:00.028 WRITE UNCORRECTABLE EXT 06 00 00 00 00 ec 00 00 a0 00 00 00 03 00:00:00.028 DATA SET MANAGEMENT 06 00 46 00 00 ef 00 00 a0 00 00 00 00 00:00:00.028 DATA SET MANAGEMENT 06 00 00 00 00 27 00 00 e0 00 00 00 00 13:58:51.676 DATA SET MANAGEMENT 00 00 14 00 80 00 00 00 00 00 40 00 a0 00:00:08.407 NOP [Reserved subcommand] [OBS-ACS-2] Error 2127 [6] occurred at disk power-on lifetime: 8848 hours (368 days + 16 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 08 -- 00 00 00 e0 00 00 00 00 00 c8 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 6c 00 00 00 00 27 00 00 e0 00 00 00 00 00:00:00.028 [RESERVED] 2e 00 00 00 00 ec 00 00 a0 00 00 00 03 00:00:00.028 [RESERVED] 2e 00 46 00 00 ef 00 00 a0 00 00 00 00 00:00:00.028 [RESERVED] 2e 00 00 00 00 27 00 00 e0 00 00 00 00 13:58:51.676 [RESERVED] 00 00 14 00 80 00 00 00 00 00 40 00 a0 00:00:08.407 NOP [Reserved subcommand] [OBS-ACS-2] Error 2126 [5] occurred at disk power-on lifetime: 8848 hours (368 days + 16 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 08 -- 00 00 00 e0 00 00 00 00 00 c8 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 94 00 00 00 00 27 00 00 e0 00 00 00 00 00:00:00.028 STANDBY IMMEDIATE [RET-4] 55 00 00 00 00 ec 00 00 a0 00 00 00 03 00:00:00.028 [RESERVED] 55 00 46 00 00 ef 00 00 a0 00 00 00 00 00:00:00.028 [RESERVED] 55 00 00 00 00 27 00 00 e0 00 00 00 00 13:58:51.676 [RESERVED] 00 00 15 00 80 00 00 00 00 00 40 00 a0 00:00:08.407 NOP [Reserved subcommand] [OBS-ACS-2] Error 2125 [4] occurred at disk power-on lifetime: 8847 hours (368 days + 15 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 08 -- 00 00 00 e0 00 00 00 00 00 c8 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 0c 00 00 00 00 27 00 00 e0 00 00 00 00 00:00:00.028 [RESERVED] 0c 00 00 00 00 ec 00 00 a0 00 00 00 03 00:00:00.028 [RESERVED] 0c 00 46 00 00 ef 00 00 a0 00 00 00 00 00:00:00.028 [RESERVED] 0c 00 00 00 00 27 00 00 e0 00 00 00 00 13:58:51.676 [RESERVED] 08 11 89 11 91 00 00 11 00 c9 b1 01 11 00:00:00.000 DEVICE RESET Error 2124 [3] occurred at disk power-on lifetime: 25408 hours (1058 days + 16 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 14 00 80 00 00 00 00 00 40 00 a0 00:00:08.407 NOP [Reserved subcommand] [OBS-ACS-2] Error 2123 [2] occurred at disk power-on lifetime: 8848 hours (368 days + 16 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 ec a0 00 00 2f 00 1c 55 08 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 1c 00 00 46 03 55 a0 00 ef 00 00 2f 1c 00:00:00.000 RECALIBRATE [RET-4] 00 00 00 00 00 00 00 00 00 00 00 00 00 9d+04:36:00.288 NOP [Abort queued commands] d7 00 80 00 40 00 00 00 00 00 00 03 00 00:00:00.000 [RESERVED] ac 00 00 08 40 00 e0 00 51 00 00 11 1c 4d+04:46:56.143 [RESERVED] 00 a0 00 0c ec 08 00 1c 00 00 1c 00 00 9d+02:19:19.136 NOP [Abort queued commands] Error 2122 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 40 00 00 d7 00 00 03 00 00 20 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 92 08 40 00 00 ac 00 e0 11 51 00 98 00 24d+20:31:28.928 DOWNLOAD MICROCODE [Reserved subcommand] e0 33 ec 1c 0b 00 08 00 00 00 00 00 a0 00:30:42.063 STANDBY IMMEDIATE 00 46 03 00 00 1c 33 a0 0b ef 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] a0 00 00 00 00 00 00 00 00 00 00 00 00 00:30:37.813 PACKET Error 2121 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 22 00 00 98 11 51 ac 00 e0 98 08 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 78 1b fc 00 00 e0 00 08 00 00 00 c8 cc 12d+10:15:41.852 ACCESSIBLE MAX ADDRESS CONFIGURATION 00 00 00 a0 00 00 1b cc 00 fc ef 00 46 45d+22:45:08.736 NOP [Abort queued commands] 8d 00 00 00 00 a0 00 00 00 00 00 ec 00 13:58:51.675 [VENDOR SPECIFIC] 00 00 00 00 00 00 d7 00 20 03 00 00 00 00:00:00.000 NOP [Abort queued commands] a0 00 00 e0 00 98 ac 00 98 11 51 22 08 12d+10:16:14.592 PACKET SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 28/30 Celsius Lifetime Min/Max Temperature: 9/51 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (94) Index Estimated Time Temperature Celsius 95 2021-06-04 01:01 32 ************* ... ..( 6 skipped). .. ************* 102 2021-06-04 01:08 32 ************* 103 2021-06-04 01:09 31 ************ 104 2021-06-04 01:10 32 ************* ... ..( 15 skipped). .. ************* 120 2021-06-04 01:26 32 ************* 121 2021-06-04 01:27 31 ************ 122 2021-06-04 01:28 32 ************* ... ..( 6 skipped). .. ************* 1 2021-06-04 01:35 32 ************* 2 2021-06-04 01:36 31 ************ 3 2021-06-04 01:37 32 ************* ... ..( 5 skipped). .. ************* 9 2021-06-04 01:43 32 ************* 10 2021-06-04 01:44 31 ************ 11 2021-06-04 01:45 32 ************* ... ..( 20 skipped). .. ************* 32 2021-06-04 02:06 32 ************* 33 2021-06-04 02:07 31 ************ 34 2021-06-04 02:08 32 ************* ... ..( 50 skipped). .. ************* 85 2021-06-04 02:59 32 ************* 86 2021-06-04 03:00 28 ********* 87 2021-06-04 03:01 29 ********** ... ..( 4 skipped). .. ********** 92 2021-06-04 03:06 29 ********** 93 2021-06-04 03:07 30 *********** 94 2021-06-04 03:08 32 ************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8001 2 0 Vendor specific