/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 Device Model: ST31000524AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: JC4B User Capacity: 1 000 204 886 016 bytes [1,00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun May 1 08:54:06 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 208 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 609) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 178) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 118 079 006 - 178057827 3 Spin_Up_Time PO---- 100 100 000 - 0 4 Start_Stop_Count -O--CK 093 093 020 - 7349 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 069 060 030 - 55939524882 9 Power_On_Hours -O--CK 078 078 000 - 19345 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 094 094 020 - 6657 183 Runtime_Bad_Block -O--CK 096 096 000 - 4 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 7956 188 Command_Timeout -O--CK 100 098 000 - 4295033220 189 High_Fly_Writes -O-RCK 098 098 000 - 2 190 Airflow_Temperature_Cel -O---K 068 053 045 - 32 (Min/Max 22/32) 194 Temperature_Celsius -O---K 032 047 000 - 32 (0 15 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 029 018 000 - 178057827 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 3 240 Head_Flying_Hours ------ 100 253 000 - 28168 (233 109 0) 241 Total_LBAs_Written ------ 100 253 000 - 1648028786 242 Total_LBAs_Read ------ 100 253 000 - 147154477 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 8002 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 8002 [1] occurred at disk power-on lifetime: 2551 hours (106 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 21 e9 b6 1a 00 00 Error: UNC at LBA = 0x21e9b61a = 568964634 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 21 e9 b6 07 e0 00 02:31:22.577 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 02:31:22.577 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 02:31:22.576 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 02:31:22.575 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 02:31:22.575 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 8001 [0] occurred at disk power-on lifetime: 2551 hours (106 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 21 e9 b6 1a 00 00 Error: UNC at LBA = 0x21e9b61a = 568964634 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 21 e9 b6 07 e0 00 02:31:19.793 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 02:31:19.792 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 02:31:19.791 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 02:31:19.791 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 02:31:19.791 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 8000 [19] occurred at disk power-on lifetime: 2551 hours (106 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 21 e9 b6 1a 00 00 Error: UNC at LBA = 0x21e9b61a = 568964634 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 21 e9 b6 07 e0 00 02:31:16.924 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 02:31:16.924 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 02:31:16.923 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 02:31:16.922 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 02:31:16.922 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 7999 [18] occurred at disk power-on lifetime: 2551 hours (106 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 21 e9 b6 1a 00 00 Error: UNC at LBA = 0x21e9b61a = 568964634 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 21 e9 b6 07 e0 00 02:31:14.149 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 02:31:14.148 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 02:31:14.147 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 02:31:14.147 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 02:31:14.147 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 7998 [17] occurred at disk power-on lifetime: 2551 hours (106 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 21 e9 b6 1a 00 00 Error: UNC at LBA = 0x21e9b61a = 568964634 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 21 e9 b6 07 e0 00 02:31:11.305 READ DMA EXT ef 00 90 00 03 00 00 00 00 00 00 a0 00 02:31:11.291 SET FEATURES [Disable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 02:31:11.291 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 02:31:11.290 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 02:31:11.290 SET FEATURES [Set transfer mode] Error 7997 [16] occurred at disk power-on lifetime: 2551 hours (106 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 21 e9 b6 1a 00 00 Error: UNC at LBA = 0x21e9b61a = 568964634 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 00 21 e9 b5 47 40 00 02:31:08.068 READ FPDMA QUEUED 60 00 00 00 10 00 00 21 e9 b5 37 40 00 02:31:08.046 READ FPDMA QUEUED 60 00 00 00 40 00 00 0b fd 20 c7 40 00 02:31:08.037 READ FPDMA QUEUED 60 00 00 00 10 00 00 0b fd 20 b7 40 00 02:31:08.035 READ FPDMA QUEUED 60 00 00 00 f8 00 00 07 90 e0 5f 40 00 02:31:08.034 READ FPDMA QUEUED Error 7996 [15] occurred at disk power-on lifetime: 2551 hours (106 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 21 e9 b6 1a 00 00 Error: WP at LBA = 0x21e9b61a = 568964634 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 02 58 00 00 0c ad cf bf 40 00 02:29:05.298 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 0c ad cb bf 40 00 02:29:05.295 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 0c ad c7 bf 40 00 02:29:05.293 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 0c ad c3 bf 40 00 02:29:05.291 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 0c ad bf bf 40 00 02:29:05.290 WRITE FPDMA QUEUED Error 7995 [14] occurred at disk power-on lifetime: 2551 hours (106 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 21 e9 b6 1a 00 00 Error: WP at LBA = 0x21e9b61a = 568964634 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 04 00 00 00 0c 6a f4 a7 40 00 02:29:01.937 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 0c 6a f0 a7 40 00 02:29:01.937 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 0c 6a ec a7 40 00 02:29:01.935 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 0c 6a ce 3f 40 00 02:29:01.933 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 0c 6a ca 3f 40 00 02:29:01.931 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Interrupted (host reset) 80% 19331 - # 2 Extended offline Interrupted (host reset) 50% 19226 - # 3 Extended offline Interrupted (host reset) 20% 19017 - # 4 Extended offline Interrupted (host reset) 70% 18909 - # 5 Extended offline Interrupted (host reset) 20% 18806 - # 6 Extended offline Interrupted (host reset) 70% 18697 - # 7 Extended offline Completed without error 00% 18590 - # 8 Short offline Completed without error 00% 12149 - # 9 Short offline Completed without error 00% 11917 - #10 Short offline Completed without error 00% 6353 - #11 Short offline Completed without error 00% 5936 - #12 Short offline Completed without error 00% 3503 - #13 Short offline Completed without error 00% 3363 - #14 Short offline Completed without error 00% 3283 - #15 Short offline Completed without error 00% 3169 - #16 Extended offline Aborted by host 90% 3169 - #17 Short offline Completed without error 00% 3101 - #18 Short offline Completed without error 00% 3025 - #19 Short offline Completed without error 00% 2965 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 22/32 Celsius Lifetime Min/Max Temperature: 15/47 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (125) Index Estimated Time Temperature Celsius 126 2016-04-26 03:30 ? - 127 2016-04-26 04:29 25 ****** 0 2016-04-26 05:28 25 ****** 1 2016-04-26 06:27 31 ************ 2 2016-04-26 07:26 32 ************* 3 2016-04-26 08:25 31 ************ 4 2016-04-26 09:24 32 ************* 5 2016-04-26 10:23 31 ************ 6 2016-04-26 11:22 32 ************* ... ..( 5 skipped). .. ************* 12 2016-04-26 17:16 32 ************* 13 2016-04-26 18:15 ? - 14 2016-04-26 19:14 22 *** 15 2016-04-26 20:13 22 *** 16 2016-04-26 21:12 31 ************ 17 2016-04-26 22:11 31 ************ 18 2016-04-26 23:10 32 ************* ... ..( 10 skipped). .. ************* 29 2016-04-27 09:59 32 ************* 30 2016-04-27 10:58 ? - 31 2016-04-27 11:57 22 *** 32 2016-04-27 12:56 22 *** 33 2016-04-27 13:55 32 ************* ... ..( 3 skipped). .. ************* 37 2016-04-27 17:51 32 ************* 38 2016-04-27 18:50 33 ************** 39 2016-04-27 19:49 32 ************* 40 2016-04-27 20:48 32 ************* 41 2016-04-27 21:47 32 ************* 42 2016-04-27 22:46 33 ************** 43 2016-04-27 23:45 33 ************** 44 2016-04-28 00:44 32 ************* 45 2016-04-28 01:43 33 ************** 46 2016-04-28 02:42 33 ************** 47 2016-04-28 03:41 ? - 48 2016-04-28 04:40 23 **** 49 2016-04-28 05:39 23 **** 50 2016-04-28 06:38 32 ************* ... ..( 2 skipped). .. ************* 53 2016-04-28 09:35 32 ************* 54 2016-04-28 10:34 33 ************** ... ..( 2 skipped). .. ************** 57 2016-04-28 13:31 33 ************** 58 2016-04-28 14:30 32 ************* 59 2016-04-28 15:29 33 ************** ... ..( 2 skipped). .. ************** 62 2016-04-28 18:26 33 ************** 63 2016-04-28 19:25 ? - 64 2016-04-28 20:24 23 **** 65 2016-04-28 21:23 23 **** 66 2016-04-28 22:22 32 ************* 67 2016-04-28 23:21 32 ************* 68 2016-04-29 00:20 33 ************** ... ..( 10 skipped). .. ************** 79 2016-04-29 11:09 33 ************** 80 2016-04-29 12:08 ? - 81 2016-04-29 13:07 23 **** 82 2016-04-29 14:06 23 **** 83 2016-04-29 15:05 32 ************* 84 2016-04-29 16:04 32 ************* 85 2016-04-29 17:03 32 ************* 86 2016-04-29 18:02 33 ************** ... ..( 5 skipped). .. ************** 92 2016-04-29 23:56 33 ************** 93 2016-04-30 00:55 32 ************* 94 2016-04-30 01:54 33 ************** ... ..( 2 skipped). .. ************** 97 2016-04-30 04:51 33 ************** 98 2016-04-30 05:50 ? - 99 2016-04-30 06:49 23 **** 100 2016-04-30 07:48 ? - 101 2016-04-30 08:47 32 ************* 102 2016-04-30 09:46 ? - 103 2016-04-30 10:45 32 ************* 104 2016-04-30 11:44 ? - 105 2016-04-30 12:43 32 ************* 106 2016-04-30 13:42 32 ************* 107 2016-04-30 14:41 ? - 108 2016-04-30 15:40 32 ************* 109 2016-04-30 16:39 ? - 110 2016-04-30 17:38 26 ******* 111 2016-04-30 18:37 26 ******* 112 2016-04-30 19:36 33 ************** ... ..( 3 skipped). .. ************** 116 2016-04-30 23:32 33 ************** 117 2016-05-01 00:31 32 ************* ... ..( 2 skipped). .. ************* 120 2016-05-01 03:28 32 ************* 121 2016-05-01 04:27 33 ************** 122 2016-05-01 05:26 ? - 123 2016-05-01 06:25 22 *** 124 2016-05-01 07:24 22 *** 125 2016-05-01 08:23 32 ************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 13 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdb === START OF INFORMATION SECTION === Device Model: PLEXTOR PX-AG128M6e Serial Number: -- LU WWN Device Id: 5 002303 ... Add. Product Id: V27020C0 Firmware Version: 1.04 User Capacity: 128 035 676 160 bytes [128 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS, ATA/ATAPI-7 T13/1532D revision 4a SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun May 1 08:54:06 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 10) seconds. Offline data collection capabilities: (0x15) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO---- 100 100 070 - 0 5 Reallocated_Sector_Ct PO---- 100 100 000 - 0 9 Power_On_Hours -O---- 100 100 000 - 83 12 Power_Cycle_Count -O---- 100 100 000 - 427 177 Wear_Leveling_Count PO---- 100 100 000 - 19651 178 Used_Rsvd_Blk_Cnt_Chip PO---- 100 100 000 - 0 181 Program_Fail_Cnt_Total PO---- 100 100 000 - 0 182 Erase_Fail_Count_Total PO---- 100 100 000 - 0 187 Reported_Uncorrect -O---- 100 100 000 - 0 192 Power-Off_Retract_Count PO---- 100 100 000 - 65 196 Reallocated_Event_Count PO---- 100 100 000 - 0 198 Offline_Uncorrectable PO---- 100 100 000 - 0 199 UDMA_CRC_Error_Count PO---- 100 100 000 - 0 232 Available_Reservd_Space PO---- 100 100 010 - 0 241 Total_LBAs_Written PO---- 100 100 000 - 46426 242 Total_LBAs_Read PO---- 100 100 000 - 30986 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 0 SMART Log Directory Version 0 Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 1 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 0 No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 20992 - # 2 Extended offline Completed without error 00% 19968 - # 3 Extended offline Completed without error 00% 17408 - # 4 Extended offline Completed without error 00% 16384 - # 5 Extended offline Completed without error 00% 15104 - # 6 Extended offline Completed without error 00% 14336 - # 7 Extended offline Completed without error 00% 13312 - # 8 Extended offline Aborted by host 10% 256 - Selective Self-tests/Logging not supported SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) SCT Support Level: 1 Device State: Active (0) Current Temperature: ? Celsius Power Cycle Min/Max Temperature: ?/ ? Celsius Lifetime Min/Max Temperature: ?/ ? Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 0 minutes Temperature Logging Interval: 0 minutes Min/Max recommended Temperature: ?/ ? Celsius Min/Max Temperature Limit: ?/ ? Celsius Temperature History Size (Index): 128 (0) Index Estimated Time Temperature Celsius 1 2016-05-01 06:47 ? - ... ..(126 skipped). .. - 0 2016-05-01 08:54 ? - SCT Error Recovery Control: Read: 2 (0,2 seconds) Write: 2 (0,2 seconds) Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 18 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC