/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.6.14-1-default] (SUSE RPM) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint M7E (AF) Device Model: SAMSUNG HM641JI Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 2AJ100P5 User Capacity: 640,135,028,736 bytes [640 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Jun 3 15:57:02 2020 MDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 121) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: ( 9720) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 162) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 7903 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 092 069 025 - 2672 4 Start_Stop_Count -O--CK 092 092 000 - 8883 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 24710 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 093 093 000 - 7871 12 Power_Cycle_Count -O--CK 092 092 000 - 8856 191 G-Sense_Error_Rate -O---K 099 099 000 - 19027 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 058 042 000 - 42 (Min/Max 6/59) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 1 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 6449 223 Load_Retry_Count -O--CK 093 093 000 - 7871 225 Load_Cycle_Count -O--CK 053 053 000 - 477258 254 Free_Fall_Sensor -O--CK 100 100 --- - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 5822 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5822 [5] occurred at disk power-on lifetime: 24494 hours (1020 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 01 bd 0e 60 40 00 Error: UNC at LBA = 0x01bd0e60 = 29167200 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 01 00 00 01 bd 0e 60 40 00 00:00:00.256 READ FPDMA QUEUED 60 00 02 00 01 00 00 01 bd 0e 60 40 00 00:00:00.302 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.302 SET FEATURES [Enable write cache] 00 00 02 00 01 00 00 01 bd 0e 41 40 00 00:00:00.302 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 02 00 01 00 00 01 bd 0e 41 40 00 00:00:00.302 NOP [Reserved subcommand] [OBS-ACS-2] Error 5821 [4] occurred at disk power-on lifetime: 24494 hours (1020 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 01 bd 0e 60 40 00 Error: UNC at LBA = 0x01bd0e60 = 29167200 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 01 00 00 01 bd 0e 60 40 00 00:00:00.254 READ FPDMA QUEUED 60 00 02 00 01 00 00 01 bd 0e 60 40 00 00:00:00.300 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.300 SET FEATURES [Enable write cache] 00 00 02 00 01 00 00 01 bd 0e 40 40 00 00:00:00.300 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 02 00 01 00 00 01 bd 0e 3f 40 00 00:00:00.300 NOP [Reserved subcommand] [OBS-ACS-2] Error 5820 [3] occurred at disk power-on lifetime: 24494 hours (1020 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 01 bd 0e 60 40 00 Error: UNC at LBA = 0x01bd0e60 = 29167200 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 01 00 00 01 bd 0e 60 40 00 00:00:00.252 READ FPDMA QUEUED 60 00 02 00 01 00 00 01 bd 0e 60 40 00 00:00:00.298 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.298 SET FEATURES [Enable write cache] 00 00 02 00 01 00 00 01 bd 0e 3e 40 00 00:00:00.298 NOP [Reserved subcommand] [OBS-ACS-2] 60 00 02 00 01 00 00 01 bd 0e 60 40 00 00:00:00.251 READ FPDMA QUEUED Error 5819 [2] occurred at disk power-on lifetime: 24494 hours (1020 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 01 bd 0e 60 40 00 Error: UNC at LBA = 0x01bd0e60 = 29167200 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 01 00 00 01 bd 0e 60 40 00 00:00:00.251 READ FPDMA QUEUED 60 00 02 00 01 00 00 01 bd 0e 60 40 00 00:00:00.296 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.296 SET FEATURES [Enable write cache] 00 00 02 00 01 00 00 01 bd 0e 3d 40 00 00:00:00.296 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 02 00 01 00 00 01 bd 0e 3c 40 00 00:00:00.296 NOP [Reserved subcommand] [OBS-ACS-2] Error 5818 [1] occurred at disk power-on lifetime: 24494 hours (1020 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 01 bd 0e 60 40 00 Error: UNC at LBA = 0x01bd0e60 = 29167200 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 01 00 00 01 bd 0e 60 40 00 00:00:00.249 READ FPDMA QUEUED 60 00 02 00 01 00 00 01 bd 0e 60 40 00 00:00:00.294 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.294 SET FEATURES [Enable write cache] 00 00 02 00 01 00 00 01 bd 0e 3b 40 00 00:00:00.294 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 02 00 01 00 00 01 bd 0e 3b 40 00 00:00:00.294 NOP [Reserved subcommand] [OBS-ACS-2] Error 5817 [0] occurred at disk power-on lifetime: 24494 hours (1020 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 01 bd 0e 60 40 00 Error: UNC at LBA = 0x01bd0e60 = 29167200 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 01 00 00 01 bd 0e 60 40 00 00:00:00.248 READ FPDMA QUEUED 60 00 02 00 01 00 00 01 bd 0e 60 40 00 00:00:00.291 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.291 SET FEATURES [Enable write cache] 00 00 02 00 01 00 00 01 bd 0e 39 40 00 00:00:00.291 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 02 00 01 00 00 01 bd 0e 39 40 00 00:00:00.291 NOP [Reserved subcommand] [OBS-ACS-2] Error 5816 [7] occurred at disk power-on lifetime: 24494 hours (1020 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 01 bd 0e 60 40 00 Error: UNC at LBA = 0x01bd0e60 = 29167200 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 01 00 00 01 bd 0e 60 40 00 00:00:00.246 READ FPDMA QUEUED 60 00 02 00 01 00 00 01 bd 0e 60 40 00 00:00:00.289 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.289 SET FEATURES [Enable write cache] 00 00 02 00 01 00 00 01 bd 0e 38 40 00 00:00:00.289 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 02 00 01 00 00 01 bd 0e 37 40 00 00:00:00.289 NOP [Reserved subcommand] [OBS-ACS-2] Error 5815 [6] occurred at disk power-on lifetime: 24494 hours (1020 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 01 bd 0e 60 40 00 Error: UNC at LBA = 0x01bd0e60 = 29167200 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 01 00 00 01 bd 0e 60 40 00 00:00:00.244 READ FPDMA QUEUED 60 00 02 00 01 00 00 01 bd 0e 60 40 00 00:00:00.287 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.287 SET FEATURES [Enable write cache] 00 00 02 00 01 00 00 01 bd 0e 36 40 00 00:00:00.287 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 02 00 01 00 00 01 bd 0e 36 40 00 00:00:00.287 NOP [Reserved subcommand] [OBS-ACS-2] SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 90% 24701 1491445 # 2 Short offline Completed without error 00% 24690 - # 3 Short offline Completed without error 00% 24676 - # 4 Short offline Completed without error 00% 24660 - # 5 Short offline Completed without error 00% 24637 - # 6 Short offline Completed without error 00% 24615 - # 7 Short offline Completed without error 00% 24597 - # 8 Short offline Completed without error 00% 24575 - # 9 Short offline Completed without error 00% 24557 - #10 Short offline Completed without error 00% 24541 - #11 Short offline Completed without error 00% 24535 - #12 Short offline Completed without error 00% 24524 - #13 Short offline Aborted by host 90% 24506 - #14 Short offline Completed without error 00% 8375 - #15 Short offline Completed without error 00% 5319 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed_read_failure [90% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 37/40 Celsius Lifetime Min/Max Temperature: 11/64 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (107) Index Estimated Time Temperature Celsius 108 2020-06-03 05:20 44 ************************* 109 2020-06-03 05:25 43 ************************ 110 2020-06-03 05:30 44 ************************* 111 2020-06-03 05:35 45 ************************** 112 2020-06-03 05:40 46 *************************** 113 2020-06-03 05:45 46 *************************** 114 2020-06-03 05:50 46 *************************** 115 2020-06-03 05:55 45 ************************** 116 2020-06-03 06:00 44 ************************* 117 2020-06-03 06:05 44 ************************* 118 2020-06-03 06:10 44 ************************* 119 2020-06-03 06:15 45 ************************** 120 2020-06-03 06:20 45 ************************** 121 2020-06-03 06:25 44 ************************* 122 2020-06-03 06:30 44 ************************* 123 2020-06-03 06:35 44 ************************* 124 2020-06-03 06:40 43 ************************ 125 2020-06-03 06:45 43 ************************ 126 2020-06-03 06:50 43 ************************ 127 2020-06-03 06:55 44 ************************* 0 2020-06-03 07:00 44 ************************* 1 2020-06-03 07:05 44 ************************* 2 2020-06-03 07:10 45 ************************** ... ..( 2 skipped). .. ************************** 5 2020-06-03 07:25 45 ************************** 6 2020-06-03 07:30 46 *************************** ... ..( 2 skipped). .. *************************** 9 2020-06-03 07:45 46 *************************** 10 2020-06-03 07:50 47 **************************** 11 2020-06-03 07:55 47 **************************** 12 2020-06-03 08:00 46 *************************** 13 2020-06-03 08:05 47 **************************** ... ..( 5 skipped). .. **************************** 19 2020-06-03 08:35 47 **************************** 20 2020-06-03 08:40 46 *************************** 21 2020-06-03 08:45 47 **************************** 22 2020-06-03 08:50 48 ***************************** ... ..( 2 skipped). .. ***************************** 25 2020-06-03 09:05 48 ***************************** 26 2020-06-03 09:10 34 *************** 27 2020-06-03 09:15 36 ***************** 28 2020-06-03 09:20 37 ****************** 29 2020-06-03 09:25 38 ******************* 30 2020-06-03 09:30 38 ******************* 31 2020-06-03 09:35 39 ******************** 32 2020-06-03 09:40 31 ************ 33 2020-06-03 09:45 32 ************* 34 2020-06-03 09:50 32 ************* 35 2020-06-03 09:55 32 ************* 36 2020-06-03 10:00 33 ************** 37 2020-06-03 10:05 33 ************** 38 2020-06-03 10:10 34 *************** 39 2020-06-03 10:15 35 **************** 40 2020-06-03 10:20 36 ***************** 41 2020-06-03 10:25 37 ****************** 42 2020-06-03 10:30 37 ****************** 43 2020-06-03 10:35 38 ******************* 44 2020-06-03 10:40 38 ******************* 45 2020-06-03 10:45 38 ******************* 46 2020-06-03 10:50 37 ****************** 47 2020-06-03 10:55 36 ***************** 48 2020-06-03 11:00 36 ***************** 49 2020-06-03 11:05 35 **************** 50 2020-06-03 11:10 35 **************** 51 2020-06-03 11:15 36 ***************** 52 2020-06-03 11:20 37 ****************** 53 2020-06-03 11:25 36 ***************** 54 2020-06-03 11:30 37 ****************** 55 2020-06-03 11:35 37 ****************** 56 2020-06-03 11:40 36 ***************** ... ..( 2 skipped). .. ***************** 59 2020-06-03 11:55 36 ***************** 60 2020-06-03 12:00 37 ****************** 61 2020-06-03 12:05 38 ******************* 62 2020-06-03 12:10 37 ****************** 63 2020-06-03 12:15 37 ****************** 64 2020-06-03 12:20 37 ****************** 65 2020-06-03 12:25 38 ******************* 66 2020-06-03 12:30 38 ******************* 67 2020-06-03 12:35 38 ******************* 68 2020-06-03 12:40 40 ********************* 69 2020-06-03 12:45 41 ********************** 70 2020-06-03 12:50 43 ************************ 71 2020-06-03 12:55 44 ************************* ... ..( 3 skipped). .. ************************* 75 2020-06-03 13:15 44 ************************* 76 2020-06-03 13:20 43 ************************ ... ..( 2 skipped). .. ************************ 79 2020-06-03 13:35 43 ************************ 80 2020-06-03 13:40 44 ************************* 81 2020-06-03 13:45 45 ************************** 82 2020-06-03 13:50 44 ************************* 83 2020-06-03 13:55 43 ************************ ... ..( 7 skipped). .. ************************ 91 2020-06-03 14:35 43 ************************ 92 2020-06-03 14:40 42 *********************** ... ..( 2 skipped). .. *********************** 95 2020-06-03 14:55 42 *********************** 96 2020-06-03 15:00 41 ********************** 97 2020-06-03 15:05 43 ************************ 98 2020-06-03 15:10 44 ************************* 99 2020-06-03 15:15 45 ************************** 100 2020-06-03 15:20 46 *************************** 101 2020-06-03 15:25 46 *************************** 102 2020-06-03 15:30 46 *************************** 103 2020-06-03 15:35 47 **************************** 104 2020-06-03 15:40 37 ****************** 105 2020-06-03 15:45 40 ********************* 106 2020-06-03 15:50 39 ******************** 107 2020-06-03 15:55 40 ********************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 23698 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific