/dev/nvme0n1 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.0-20-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: Force MP600 Serial Number: -- Firmware Version: EGFM13.0 PCI Vendor/Subsystem ID: 0x1987 IEEE OUI Identifier: 0x6479a7 Total NVM Capacity: 1,000,204,886,016 [1.00 TB] Unallocated NVM Capacity: 0 Controller ID: 1 NVMe Version: 1.3 Number of Namespaces: 1 Namespace 1 Size/Capacity: 1,000,204,886,016 [1.00 TB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 6479a7 ... Local Time is: Mon Jul 3 16:59:54 2023 CEST Firmware Updates (0x12): 1 Slot, no Reset required Optional Admin Commands (0x0017): Security Format Frmw_DL Self_Test Optional NVM Commands (0x005d): Comp DS_Mngmt Wr_Zero Sav/Sel_Feat Timestmp Log Page Attributes (0x08): Telmtry_Lg Maximum Data Transfer Size: 512 Pages Warning Comp. Temp. Threshold: 90 Celsius Critical Comp. Temp. Threshold: 95 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 9.78W - - 0 0 0 0 0 0 1 + 6.75W - - 1 1 1 1 0 0 2 + 5.23W - - 2 2 2 2 0 0 3 - 0.0490W - - 3 3 3 3 2000 2000 4 - 0.0018W - - 4 4 4 4 25000 25000 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 2 1 - 4096 0 1 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02) Critical Warning: 0x00 Temperature: 44 Celsius Available Spare: 100% Available Spare Threshold: 5% Percentage Used: 2% Data Units Read: 48,214,654 [24.6 TB] Data Units Written: 48,053,396 [24.6 TB] Host Read Commands: 667,502,925 Host Write Commands: 400,720,278 Controller Busy Time: 859 Power Cycles: 1,375 Power On Hours: 4,649 Unsafe Shutdowns: 272 Media and Data Integrity Errors: 0 Error Information Log Entries: 3,166 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Error Information (NVMe Log 0x01, 16 of 63 entries) Num ErrCount SQId CmdId Status PELoc LBA NSID VS 0 3166 0 0x000c 0x4004 0x028 0 0 - /dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.0-20-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WD Blue SA510 2.5 1000GB Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: 52008100 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: Not in smartctl database 7.3/5319 ATA Version is: ACS-4, ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jul 3 16:59:54 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 10) minutes. Conveyance self-test routine recommended polling time: ( 1) minutes. SMART Attributes Data Structure revision number: 0 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 010 - 3 9 Power_On_Hours -O--CK 100 100 000 - 14 12 Power_Cycle_Count -O--CK 100 100 000 - 335 165 Unknown_Attribute -O--CK 100 100 000 - 60134981709 166 Unknown_Attribute -O--CK 100 100 000 - 1 167 Unknown_Attribute -O--CK 100 100 000 - 20 168 Unknown_Attribute -O--CK 100 100 000 - 6 169 Unknown_Attribute -O--CK 100 100 000 - 203 170 Unknown_Attribute -O--CK 100 100 000 - 3 171 Unknown_Attribute -O--CK 100 100 000 - 0 172 Unknown_Attribute -O--CK 100 100 000 - 0 173 Unknown_Attribute -O--CK 100 100 005 - 2 174 Unknown_Attribute -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 100 100 014 - 28 (Min/Max 14/39) 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 230 Unknown_SSD_Attribute -O--CK 100 100 000 - 81607000083 232 Available_Reservd_Space PO--CK 100 100 004 - 91 233 Media_Wearout_Indicator -O--CK 100 100 000 - 1091 234 Unknown_Attribute -O--CK 100 100 000 - 2805 241 Total_LBAs_Written ----CK 253 253 000 - 2379 242 Total_LBAs_Read ----CK 253 253 000 - 1811 244 Unknown_Attribute -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3-0xa7 GPL,SL VS 1 Device vendor specific log 0xde GPL,SL VS 1 Device vendor specific log Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (empty) == 0x05 ===== = = === == Temperature Statistics (empty) == 0x07 ===== = = === == Solid State Device Statistics (empty) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 11 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.0-20-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 850 EVO 1TB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: EMT02B6Q User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jul 3 16:59:54 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 512) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 096 096 000 - 17386 12 Power_Cycle_Count -O--CK 093 093 000 - 6276 177 Wear_Leveling_Count PO--C- 097 097 000 - 59 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 071 044 000 - 29 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 099 099 000 - 1 235 POR_Recovery_Count -O--C- 099 099 000 - 1798 241 Total_LBAs_Written -O--CK 099 099 000 - 86145711078 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 14032 - # 2 Short offline Completed without error 00% 14002 - # 3 Short offline Completed without error 00% 13928 - # 4 Short offline Completed without error 00% 13913 - # 5 Short offline Completed without error 00% 10535 - # 6 Short offline Completed without error 00% 10522 - # 7 Short offline Completed without error 00% 10518 - # 8 Short offline Completed without error 00% 10458 - # 9 Extended offline Interrupted (host reset) 70% 10437 - #10 Short offline Completed without error 00% 10428 - #11 Extended offline Interrupted (host reset) 10% 10426 - #12 Short offline Completed without error 00% 10383 - #13 Short offline Completed without error 00% 10358 - #14 Short offline Completed without error 00% 10346 - #15 Short offline Completed without error 00% 10335 - #16 Short offline Completed without error 00% 10323 - #17 Short offline Completed without error 00% 10314 - #18 Short offline Completed without error 00% 10311 - #19 Short offline Completed without error 00% 10296 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 28/28 Celsius Lifetime Min/Max Temperature: 16/56 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (17) Index Estimated Time Temperature Celsius 18 2023-07-02 19:40 32 ************* ... ..( 2 skipped). .. ************* 21 2023-07-02 20:10 32 ************* 22 2023-07-02 20:20 31 ************ 23 2023-07-02 20:30 31 ************ 24 2023-07-02 20:40 31 ************ 25 2023-07-02 20:50 ? - 26 2023-07-02 21:00 28 ********* 27 2023-07-02 21:10 ? - 28 2023-07-02 21:20 27 ******** 29 2023-07-02 21:30 28 ********* 30 2023-07-02 21:40 ? - 31 2023-07-02 21:50 26 ******* 32 2023-07-02 22:00 ? - 33 2023-07-02 22:10 26 ******* 34 2023-07-02 22:20 ? - 35 2023-07-02 22:30 29 ********** 36 2023-07-02 22:40 31 ************ 37 2023-07-02 22:50 32 ************* 38 2023-07-02 23:00 35 **************** 39 2023-07-02 23:10 34 *************** 40 2023-07-02 23:20 34 *************** 41 2023-07-02 23:30 34 *************** 42 2023-07-02 23:40 33 ************** 43 2023-07-02 23:50 35 **************** 44 2023-07-03 00:00 33 ************** 45 2023-07-03 00:10 37 ****************** 46 2023-07-03 00:20 34 *************** 47 2023-07-03 00:30 34 *************** 48 2023-07-03 00:40 34 *************** 49 2023-07-03 00:50 33 ************** 50 2023-07-03 01:00 33 ************** 51 2023-07-03 01:10 34 *************** 52 2023-07-03 01:20 34 *************** 53 2023-07-03 01:30 35 **************** ... ..( 2 skipped). .. **************** 56 2023-07-03 02:00 35 **************** 57 2023-07-03 02:10 40 ********************* 58 2023-07-03 02:20 36 ***************** 59 2023-07-03 02:30 36 ***************** 60 2023-07-03 02:40 35 **************** 61 2023-07-03 02:50 35 **************** 62 2023-07-03 03:00 34 *************** ... ..( 2 skipped). .. *************** 65 2023-07-03 03:30 34 *************** 66 2023-07-03 03:40 33 ************** 67 2023-07-03 03:50 32 ************* 68 2023-07-03 04:00 32 ************* 69 2023-07-03 04:10 ? - 70 2023-07-03 04:20 26 ******* 71 2023-07-03 04:30 28 ********* 72 2023-07-03 04:40 29 ********** 73 2023-07-03 04:50 30 *********** 74 2023-07-03 05:00 31 ************ 75 2023-07-03 05:10 ? - 76 2023-07-03 05:20 27 ******** 77 2023-07-03 05:30 32 ************* 78 2023-07-03 05:40 31 ************ 79 2023-07-03 05:50 36 ***************** 80 2023-07-03 06:00 36 ***************** 81 2023-07-03 06:10 33 ************** 82 2023-07-03 06:20 33 ************** 83 2023-07-03 06:30 36 ***************** 84 2023-07-03 06:40 44 ************************* 85 2023-07-03 06:50 39 ******************** 86 2023-07-03 07:00 34 *************** 87 2023-07-03 07:10 36 ***************** 88 2023-07-03 07:20 34 *************** 89 2023-07-03 07:30 36 ***************** 90 2023-07-03 07:40 38 ******************* 91 2023-07-03 07:50 35 **************** 92 2023-07-03 08:00 39 ******************** 93 2023-07-03 08:10 ? - 94 2023-07-03 08:20 32 ************* 95 2023-07-03 08:30 33 ************** ... ..( 2 skipped). .. ************** 98 2023-07-03 09:00 33 ************** 99 2023-07-03 09:10 34 *************** ... ..( 10 skipped). .. *************** 110 2023-07-03 11:00 34 *************** 111 2023-07-03 11:10 37 ****************** 112 2023-07-03 11:20 34 *************** 113 2023-07-03 11:30 33 ************** 114 2023-07-03 11:40 32 ************* ... ..( 9 skipped). .. ************* 124 2023-07-03 13:20 32 ************* 125 2023-07-03 13:30 31 ************ 126 2023-07-03 13:40 30 *********** 127 2023-07-03 13:50 30 *********** 0 2023-07-03 14:00 30 *********** 1 2023-07-03 14:10 29 ********** ... ..( 11 skipped). .. ********** 13 2023-07-03 16:10 29 ********** 14 2023-07-03 16:20 28 ********* 15 2023-07-03 16:30 28 ********* 16 2023-07-03 16:40 ? - 17 2023-07-03 16:50 28 ********* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 10 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 10 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdc smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.0-20-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 850 EVO 250GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: EMT01B6Q User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jul 3 16:59:54 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 133) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 097 097 010 - 17 9 Power_On_Hours -O--CK 093 093 000 - 32468 12 Power_Cycle_Count -O--CK 097 097 000 - 2816 177 Wear_Leveling_Count PO--C- 001 001 000 - 5635 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 097 097 010 - 17 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 097 097 010 - 17 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 069 043 000 - 31 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 098 098 000 - 1262 235 POR_Recovery_Count -O--C- 099 099 000 - 618 241 Total_LBAs_Written -O--CK 099 099 000 - 250396685590 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 25519 - # 2 Extended offline Completed without error 00% 25420 - # 3 Short offline Completed without error 00% 24988 - Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum. SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SCT command executing in background (5) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 30/40 Celsius Lifetime Min/Max Temperature: 0/70 Celsius Under/Over Temperature Limit Count: 4294967295/4294901760 SMART Status: 0xffff (Reserved) SCT Temperature History Version: 3 (Unknown, should be 2) Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (1) Index Estimated Time Temperature Celsius 2 2023-07-02 19:40 ? - ... ..(124 skipped). .. - 127 2023-07-03 16:30 ? - 0 2023-07-03 16:40 40 ********************* 1 2023-07-03 16:50 30 *********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 10 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 10 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC