/dev/sda smartctl 7.1 2020-08-23 r5080 [x86_64-linux-4.18.0-477.27.2.el8_8.x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Desktop HDD.15 Device Model: ST4000DM000-1F2168 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC52 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5900 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon Dec 4 12:33:00 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 602) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 525) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 119 093 006 - 223590280 3 Spin_Up_Time PO---- 091 091 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 125 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 089 060 030 - 822484229 9 Power_On_Hours -O--CK 018 018 000 - 72523 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 115 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 091 091 000 - 9 188 Command_Timeout -O--CK 100 098 000 - 4 4 4 189 High_Fly_Writes -O-RCK 001 001 000 - 130 190 Airflow_Temperature_Cel -O---K 066 059 045 - 34 (Min/Max 19/34) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 85 193 Load_Cycle_Count -O--CK 042 042 000 - 117645 194 Temperature_Celsius -O---K 034 041 000 - 34 (0 13 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 64149h+28m+29.052s 241 Total_LBAs_Written ------ 100 253 000 - 505649704067 242 Total_LBAs_Read ------ 100 253 000 - 270304577267 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 1223 Current Device Internal Status Data log 0x25 GPL R/O 1223 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc3 GPL,SL VS 8 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 9 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 9 [8] occurred at disk power-on lifetime: 5376 hours (224 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 78 ab e4 77 00 00 Error: UNC at LBA = 0x178abe477 = 6319498359 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 89 00 01 78 ab e4 77 40 00 4d+12:46:16.765 READ FPDMA QUEUED ef 00 82 00 00 00 00 00 00 00 00 00 00 4d+12:46:16.765 SET FEATURES [Disable write cache] ef 00 aa 00 00 00 00 00 00 00 00 00 00 4d+12:46:16.765 SET FEATURES [Enable read look-ahead] ec 00 00 00 00 00 00 00 00 00 00 00 00 4d+12:46:16.736 IDENTIFY DEVICE b0 00 d0 00 00 00 00 00 c2 4f 00 00 00 4d+12:46:16.668 SMART READ DATA Error 8 [7] occurred at disk power-on lifetime: 5376 hours (224 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 78 ab e4 76 00 00 Error: UNC at LBA = 0x178abe476 = 6319498358 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 8a 00 01 78 ab e4 76 40 00 4d+12:46:12.998 READ FPDMA QUEUED 61 00 00 00 08 00 00 c2 35 2c 18 40 00 4d+12:46:12.977 WRITE FPDMA QUEUED ef 00 82 00 00 00 00 00 00 00 00 00 00 4d+12:46:12.977 SET FEATURES [Disable write cache] ef 00 aa 00 00 00 00 00 00 00 00 00 00 4d+12:46:12.977 SET FEATURES [Enable read look-ahead] ec 00 00 00 00 00 00 00 00 00 00 00 00 4d+12:46:12.977 IDENTIFY DEVICE Error 7 [6] occurred at disk power-on lifetime: 5376 hours (224 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 78 ab e4 76 00 00 Error: WP at LBA = 0x178abe476 = 6319498358 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 c2 37 61 90 40 00 4d+12:46:07.789 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 c2 35 2c 18 40 00 4d+12:46:07.784 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 c2 35 23 d8 40 00 4d+12:46:07.780 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 c2 35 1a 68 40 00 4d+12:46:07.777 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 c2 35 0a 98 40 00 4d+12:46:07.772 WRITE FPDMA QUEUED Error 6 [5] occurred at disk power-on lifetime: 5376 hours (224 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 78 ab e4 75 00 00 Error: WP at LBA = 0x178abe475 = 6319498357 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 a2 ef d7 28 40 00 4d+12:46:03.693 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 a2 ef b8 78 40 00 4d+12:46:03.681 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 a2 ef b8 48 40 00 4d+12:46:03.671 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 a2 ef 8c 68 40 00 4d+12:46:03.662 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 a2 ef 89 40 40 00 4d+12:46:03.641 WRITE FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 5376 hours (224 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 78 ab e4 74 00 00 Error: WP at LBA = 0x178abe474 = 6319498356 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 14 00 00 7e d7 c9 00 40 00 4d+12:45:58.641 WRITE FPDMA QUEUED 61 00 00 00 b0 00 00 7e d7 c8 50 40 00 4d+12:45:58.639 WRITE FPDMA QUEUED 61 00 00 00 3c 00 00 7e d3 02 00 40 00 4d+12:45:58.638 WRITE FPDMA QUEUED 61 00 00 00 88 00 00 7e d3 01 78 40 00 4d+12:45:58.637 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 7e d2 e4 90 40 00 4d+12:45:58.637 WRITE FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 5376 hours (224 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 78 ab e4 73 00 00 Error: WP at LBA = 0x178abe473 = 6319498355 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 01 00 00 00 7e a3 4c 00 40 00 4d+12:45:54.666 WRITE FPDMA QUEUED 61 00 00 01 00 00 00 7e a3 4b 00 40 00 4d+12:45:54.664 WRITE FPDMA QUEUED 61 00 00 01 00 00 00 7e a3 4a 00 40 00 4d+12:45:54.663 WRITE FPDMA QUEUED 61 00 00 01 00 00 00 7e a3 49 00 40 00 4d+12:45:54.663 WRITE FPDMA QUEUED 61 00 00 01 00 00 00 7e a3 48 00 40 00 4d+12:45:54.662 WRITE FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 5376 hours (224 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 78 ab e4 72 00 00 Error: WP at LBA = 0x178abe472 = 6319498354 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 d0 00 00 7d 3a 82 10 40 00 4d+12:45:49.476 WRITE FPDMA QUEUED 61 00 00 00 18 00 00 7d 38 e3 b8 40 00 4d+12:45:49.451 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 7d 38 d9 20 40 00 4d+12:45:49.429 WRITE FPDMA QUEUED 61 00 00 00 10 00 00 7d 33 df 90 40 00 4d+12:45:49.426 WRITE FPDMA QUEUED 61 00 00 00 10 00 00 7d 33 cb 28 40 00 4d+12:45:49.424 WRITE FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 5376 hours (224 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 78 ab e4 71 00 00 Error: WP at LBA = 0x178abe471 = 6319498353 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 10 00 00 00 18 69 50 40 00 4d+12:45:47.232 WRITE FPDMA QUEUED 61 00 00 00 04 00 00 00 17 7c 00 40 00 4d+12:45:47.232 WRITE FPDMA QUEUED 61 00 00 00 04 00 00 00 17 75 08 40 00 4d+12:45:47.231 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 c6 73 87 88 40 00 4d+12:45:47.231 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 c6 6f 64 48 40 00 4d+12:45:47.231 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 20/34 Celsius Lifetime Min/Max Temperature: 14/41 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 11 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdb smartctl 7.1 2020-08-23 r5080 [x86_64-linux-4.18.0-477.27.2.el8_8.x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD60EFRX-68L0BN1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 82.00A82 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5700 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon Dec 4 12:33:00 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6524) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 719) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 197 196 021 - 9125 4 Start_Stop_Count -O--CK 100 100 000 - 210 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 087 087 000 - 9705 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 210 192 Power-Off_Retract_Count -O--CK 200 200 000 - 43 193 Load_Cycle_Count -O--CK 200 200 000 - 2159 194 Temperature_Celsius -O---K 120 111 000 - 32 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 54 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 21/32 Celsius Lifetime Min/Max Temperature: 18/41 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (332) Index Estimated Time Temperature Celsius 333 2023-12-04 04:36 33 ************** ... ..(128 skipped). .. ************** 462 2023-12-04 06:45 33 ************** 463 2023-12-04 06:46 ? - 464 2023-12-04 06:47 21 ** 465 2023-12-04 06:48 21 ** 466 2023-12-04 06:49 22 *** 467 2023-12-04 06:50 22 *** 468 2023-12-04 06:51 22 *** 469 2023-12-04 06:52 23 **** 470 2023-12-04 06:53 23 **** 471 2023-12-04 06:54 23 **** 472 2023-12-04 06:55 24 ***** ... ..( 2 skipped). .. ***** 475 2023-12-04 06:58 24 ***** 476 2023-12-04 06:59 25 ****** ... ..( 5 skipped). .. ****** 4 2023-12-04 07:05 25 ****** 5 2023-12-04 07:06 26 ******* ... ..( 5 skipped). .. ******* 11 2023-12-04 07:12 26 ******* 12 2023-12-04 07:13 27 ******** ... ..( 8 skipped). .. ******** 21 2023-12-04 07:22 27 ******** 22 2023-12-04 07:23 28 ********* ... ..( 9 skipped). .. ********* 32 2023-12-04 07:33 28 ********* 33 2023-12-04 07:34 29 ********** ... ..( 22 skipped). .. ********** 56 2023-12-04 07:57 29 ********** 57 2023-12-04 07:58 30 *********** ... ..( 45 skipped). .. *********** 103 2023-12-04 08:44 30 *********** 104 2023-12-04 08:45 31 ************ ... ..( 49 skipped). .. ************ 154 2023-12-04 09:35 31 ************ 155 2023-12-04 09:36 32 ************* ... ..( 98 skipped). .. ************* 254 2023-12-04 11:15 32 ************* 255 2023-12-04 11:16 33 ************** ... ..( 76 skipped). .. ************** 332 2023-12-04 12:33 33 ************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 210 --- Lifetime Power-On Resets 0x01 0x010 4 9705 --- Power-on Hours 0x01 0x018 6 38957718706 --- Logical Sectors Written 0x01 0x020 6 114511725 --- Number of Write Commands 0x01 0x028 6 42166189579 --- Logical Sectors Read 0x01 0x030 6 216412418 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 9687 --- Spindle Motor Power-on Hours 0x03 0x010 4 3022 --- Head Flying Hours 0x03 0x018 4 2203 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 32 --- Current Temperature 0x05 0x010 1 30 --- Average Short Term Temperature 0x05 0x018 1 30 --- Average Long Term Temperature 0x05 0x020 1 41 --- Highest Temperature 0x05 0x028 1 21 --- Lowest Temperature 0x05 0x030 1 39 --- Highest Average Short Term Temperature 0x05 0x038 1 27 --- Lowest Average Short Term Temperature 0x05 0x040 1 34 --- Highest Average Long Term Temperature 0x05 0x048 1 28 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1721 --- Number of Hardware Resets 0x06 0x010 4 702 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 12 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 13 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 16213 Vendor specific /dev/sdc smartctl 7.1 2020-08-23 r5080 [x86_64-linux-4.18.0-477.27.2.el8_8.x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Kingston SSDNow UV400/500 Device Model: KINGSTON SUV400S37240G Serial Number: -- LU WWN Device Id: 5 0026b7 ... Firmware Version: 0C3K87RA User Capacity: 240,057,409,536 bytes [240 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-4, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon Dec 4 12:33:01 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Disabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 5) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 5) minutes. Conveyance self-test routine recommended polling time: ( 0) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 48 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 000 - 39159 5 Reallocated_Sector_Ct PO--CK 098 098 010 - 40 9 Power_On_Hours -O--CK 100 100 000 - 22822 12 Power_Cycle_Count -O--CK 100 100 000 - 2451 100 Unknown_Kingston_Attr -O--CK 100 100 000 - 17138368 101 Unknown_Kingston_Attr -O--CK 100 100 000 - 1348128 170 Reserved_Block_Count -O--CK 100 100 000 - 40 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 94 175 Program_Fail_Count_Chip -O--CK 100 100 000 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 000 - 0 177 Wear_Leveling_Count -O--CK 086 086 000 - 5149 178 Used_Rsvd_Blk_Cnt_Chip -O---- 100 100 000 - 4 180 Unused_Rsvd_Blk_Cnt_Tot -O---- 100 100 000 - 1402 183 Runtime_Bad_Block -O--CK 094 094 000 - 31 187 Reported_Uncorrect PO--CK 100 100 000 - 39075 194 Temperature_Celsius -O---K 031 100 000 - 31 (0 253 0 1 0) 195 Hardware_ECC_Recovered -O--CK 100 100 000 - 39159 196 Reallocated_Event_Count -O--CK 100 100 000 - 40 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--C- 100 100 000 - 0 201 Unc_Read_Error_Rate -O--CK 100 100 000 - 0 204 Soft_ECC_Correction -O--CK 100 100 000 - 84 231 SSD_Life_Left -O--CK 086 086 000 - 14 233 Media_Wearout_Indicator -O--CK 100 100 000 - 30029 234 Unknown_Attribute -O--CK 100 100 000 - 7564 241 Host_Writes_GiB -O--CK 100 100 000 - 17372 242 Host_Reads_GiB -O--CK 100 100 000 - 14436 250 Read_Retry_Count -O--CK 100 100 000 - 351722 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x0a GPL R/W 5 Device Statistics Notification 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 9 Device vendor specific log 0xab SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 0 (1 sectors) Device Error Count: 14409 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 14409 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 03 4b 0a a0 40 00 Error: UNC at LBA = 0x034b0aa0 = 55249568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 04 00 20 00 00 03 4b 0a a0 40 00 00:19:08.679 READ FPDMA QUEUED Error 14408 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 03 4b 0a a0 40 00 Error: UNC at LBA = 0x034b0aa0 = 55249568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 14 00 20 00 00 03 4b 0a a0 40 00 00:26:56.520 READ FPDMA QUEUED Error 14407 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 03 4b 0a a0 40 00 Error: UNC at LBA = 0x034b0aa0 = 55249568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 16 00 20 00 00 03 4b 0a a0 40 00 00:26:24.819 READ FPDMA QUEUED Error 14406 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 03 4b 0a a0 40 00 Error: UNC at LBA = 0x034b0aa0 = 55249568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 08 00 00 03 4b 0a a0 40 00 00:06:39.065 READ FPDMA QUEUED SMART Extended Self-test Log Version: 0 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 9252 - # 2 Short offline Completed without error 00% 8763 - # 3 Short offline Completed without error 00% 7891 - # 4 Short offline Completed without error 00% 7369 - # 5 Short offline Completed without error 00% 5617 - # 6 Short offline Completed without error 00% 2500 - # 7 Short offline Completed without error 00% 1816 - # 8 Short offline Completed without error 00% 1551 - # 9 Short offline Completed without error 00% 1072 - #10 Short offline Completed without error 00% 839 - #11 Short offline Completed without error 00% 726 - #12 Short offline Completed without error 00% 417 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 22/31 Celsius Lifetime Min/Max Temperature: 1/-3 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/85 Celsius Temperature History Size (Index): 478 (112) Index Estimated Time Temperature Celsius 113 2023-12-04 04:36 30 *********** ... ..(141 skipped). .. *********** 255 2023-12-04 06:58 30 *********** 256 2023-12-04 06:59 31 ************ 257 2023-12-04 07:00 30 *********** ... ..( 34 skipped). .. *********** 292 2023-12-04 07:35 30 *********** 293 2023-12-04 07:36 31 ************ 294 2023-12-04 07:37 30 *********** ... ..( 24 skipped). .. *********** 319 2023-12-04 08:02 30 *********** 320 2023-12-04 08:03 ? - 321 2023-12-04 08:04 22 *** 322 2023-12-04 08:05 23 **** 323 2023-12-04 08:06 24 ***** 324 2023-12-04 08:07 24 ***** 325 2023-12-04 08:08 25 ****** ... ..( 2 skipped). .. ****** 328 2023-12-04 08:11 25 ****** 329 2023-12-04 08:12 26 ******* ... ..( 5 skipped). .. ******* 335 2023-12-04 08:18 26 ******* 336 2023-12-04 08:19 27 ******** ... ..( 8 skipped). .. ******** 345 2023-12-04 08:28 27 ******** 346 2023-12-04 08:29 28 ********* ... ..( 22 skipped). .. ********* 369 2023-12-04 08:52 28 ********* 370 2023-12-04 08:53 29 ********** ... ..( 50 skipped). .. ********** 421 2023-12-04 09:44 29 ********** 422 2023-12-04 09:45 30 *********** ... ..( 95 skipped). .. *********** 40 2023-12-04 11:21 30 *********** 41 2023-12-04 11:22 31 ************ 42 2023-12-04 11:23 30 *********** ... ..( 4 skipped). .. *********** 47 2023-12-04 11:28 30 *********** 48 2023-12-04 11:29 31 ************ ... ..( 63 skipped). .. ************ 112 2023-12-04 12:33 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 2451 --- Lifetime Power-On Resets 0x01 0x010 4 22822 --- Power-on Hours 0x01 0x018 6 36433595055 --- Logical Sectors Written 0x01 0x020 6 1085621143 --- Number of Write Commands 0x01 0x028 6 30274722688 --- Logical Sectors Read 0x01 0x030 6 667495909 --- Number of Read Commands 0x01 0x038 6 82160723060 --- Date and Time TimeStamp 0x02 ===== = = === == Free-Fall Statistics (empty) == 0x03 ===== = = === == Rotating Media Statistics (empty) == 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 39075 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 44204 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 31 -D- Current Temperature 0x05 0x010 1 - -D- Average Short Term Temperature 0x05 0x018 1 0 -D- Average Long Term Temperature 0x05 0x020 1 -3 --- Highest Temperature 0x05 0x028 1 1 --- Lowest Temperature 0x05 0x030 1 - -D- Highest Average Short Term Temperature 0x05 0x038 1 - -D- Lowest Average Short Term Temperature 0x05 0x040 1 - -D- Highest Average Long Term Temperature 0x05 0x048 1 - -D- Lowest Average Long Term Temperature 0x05 0x050 4 0 -D- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 -D- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 44204 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 14 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x000a 4 14 Device-to-host register FISes sent due to a COMRESET