/dev/sda === START OF INFORMATION SECTION === Device Model: ACSC2M128S25 Serial Number: -- LU WWN Device Id: 0 000000 ... Firmware Version: 20151120 User Capacity: 126 701 535 232 bytes [126 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.1, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Sat Apr 8 14:44:14 2017 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Disabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate ------ 100 100 050 - 0 5 Reallocated_Sector_Ct -O---- 100 100 050 - 0 9 Power_On_Hours ------ 100 100 050 - 40 12 Power_Cycle_Count ------ 100 100 050 - 402 160 Unknown_Attribute ------ 100 100 050 - 0 161 Unknown_Attribute ------ 100 100 050 - 54 162 Unknown_Attribute ------ 100 100 050 - 1 163 Unknown_Attribute ------ 100 100 050 - 18 164 Unknown_Attribute ------ 100 100 050 - 8499 165 Unknown_Attribute ------ 100 100 050 - 13 166 Unknown_Attribute ------ 100 100 050 - 5 167 Unknown_Attribute ------ 100 100 050 - 8 168 Unknown_Attribute ------ 100 100 050 - 3000 192 Power-Off_Retract_Count ------ 100 100 050 - 32 194 Temperature_Celsius ------ 100 100 050 - 40 195 Hardware_ECC_Recovered ------ 100 100 050 - 15486 196 Reallocated_Event_Count ------ 100 100 050 - 0 199 UDMA_CRC_Error_Count ------ 100 100 050 - 5 241 Total_LBAs_Written ------ 100 100 050 - 23992 242 Total_LBAs_Read ------ 100 100 050 - 11563 245 Unknown_Attribute ------ 100 100 050 - 26854 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Invalid Error Log index = 0x0000 (reserved = 0x00) Warning! SMART Extended Self-test Log Structure error: invalid SMART checksum. SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 - Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 402 --- Lifetime Power-On Resets 0x01 0x010 4 40 --- Power-on Hours 0x01 0x018 6 1572367468 --- Logical Sectors Written 0x01 0x020 6 16603979 --- Number of Write Commands 0x01 0x028 6 757816345 --- Logical Sectors Read 0x01 0x030 6 14231785 --- Number of Read Commands 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 47105 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 40 --- Current Temperature 0x05 0x010 1 84 --- Average Short Term Temperature 0x05 0x018 1 108 --- Average Long Term Temperature 0x05 0x020 1 51 --- Highest Temperature 0x05 0x028 1 12 --- Lowest Temperature 0x05 0x030 1 84 --- Highest Average Short Term Temperature 0x05 0x038 1 0 --- Lowest Average Short Term Temperature 0x05 0x040 1 -1 --- Highest Average Long Term Temperature 0x05 0x048 1 0 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 100 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 2068 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD3200BEVT-22ZCT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 11.01A11 User Capacity: 320 072 933 376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Sat Apr 8 14:44:14 2017 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9960) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 118) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 11 3 Spin_Up_Time POS--K 188 187 021 - 1583 4 Start_Stop_Count -O--CK 096 096 000 - 4293 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 088 088 000 - 9485 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3090 192 Power-Off_Retract_Count -O--CK 200 200 000 - 207 193 Load_Cycle_Count -O--CK 175 175 000 - 76935 194 Temperature_Celsius -O---K 103 074 000 - 44 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 483 200 Multi_Zone_Error_Rate P--R-- 100 253 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 244 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 244 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 0e 60 01 33 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 d0 01 00 00 01 35 02 31 60 00 00 00 00:00:49.368 NOP [Don't abort queued commands] [OBS-ACS-2] 00 34 60 01 31 00 c8 00 00 01 00 00 00 00:01:18.133 NOP [Reserved subcommand] [OBS-ACS-2] 00 b0 01 00 00 01 27 00 31 60 00 00 00 00:00:00.184 NOP [Don't abort queued commands] [OBS-ACS-2] Error 243 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 0f 60 01 25 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 98 01 00 00 01 2d 02 23 60 00 00 00 00:00:49.312 NOP [Don't abort queued commands] [OBS-ACS-2] 00 2c 60 01 23 00 90 00 00 01 00 00 00 00:01:14.540 NOP [Reserved subcommand] [OBS-ACS-2] 00 78 01 00 00 01 1e 00 23 60 00 00 00 00:00:00.128 NOP [Don't abort queued commands] [OBS-ACS-2] Error 242 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 73 60 01 16 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 60 01 00 00 01 94 02 14 60 00 00 00 00:00:49.256 NOP [Don't abort queued commands] [OBS-ACS-2] 00 94 60 01 14 00 58 00 00 01 00 00 00 00:01:10.804 NOP [Reserved subcommand] [OBS-ACS-2] 00 40 01 00 00 01 86 00 14 60 00 00 00 00:00:00.072 NOP [Don't abort queued commands] [OBS-ACS-2] Error 241 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 64 60 01 08 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 28 01 00 00 01 8c 02 06 60 00 00 00 00:00:49.200 NOP [Don't abort queued commands] [OBS-ACS-2] 00 8b 60 01 06 00 20 00 00 01 00 00 00 00:01:07.212 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 01 00 00 01 7d 00 06 60 00 00 00 00:00:00.016 NOP [Don't abort queued commands] [OBS-ACS-2] Error 240 [23] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 01 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 81 60 00 fa 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 e0 01 00 fc 00 81 00 fa 61 00 00 00 00:00:49.400 NOP [Don't abort queued commands] [OBS-ACS-2] 00 80 61 00 fa 00 d8 00 ff 01 00 00 00 00:01:04.129 NOP [Reserved subcommand] [OBS-ACS-2] 00 a8 01 00 ff 00 80 00 fa 61 00 00 00 00:01:04.688 NOP [Don't abort queued commands] [OBS-ACS-2] Error 239 [22] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 f1 60 01 7c 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 88 01 00 00 01 1a 02 7b 60 00 00 00 00:00:49.296 NOP [Don't abort queued commands] [OBS-ACS-2] 00 19 60 01 7b 00 80 00 00 01 00 00 00 00:01:37.049 NOP [Reserved subcommand] [OBS-ACS-2] 00 68 01 00 00 01 0b 00 7b 60 00 00 00 00:00:00.112 NOP [Don't abort queued commands] [OBS-ACS-2] Error 238 [21] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 4c 60 01 6d 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 50 01 00 00 01 77 02 6b 60 00 00 00 00:00:49.240 NOP [Don't abort queued commands] [OBS-ACS-2] 00 77 60 01 6b 00 48 00 00 01 00 00 00 00:01:33.047 NOP [Reserved subcommand] [OBS-ACS-2] 00 30 01 00 00 01 69 00 6b 60 00 00 00 00:00:00.056 NOP [Don't abort queued commands] [OBS-ACS-2] Error 237 [20] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 c0 60 01 5e 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 18 01 00 00 01 ea 02 5c 60 00 00 00 00:00:49.184 NOP [Don't abort queued commands] [OBS-ACS-2] 00 e9 60 01 5c 00 10 00 00 01 00 00 00 00:01:29.322 NOP [Reserved subcommand] [OBS-ACS-2] 00 f8 01 00 00 01 db 00 5c 60 00 00 00 00:00:00.000 NOP [Don't abort queued commands] [OBS-ACS-2] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 8477 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 44 Celsius Power Cycle Min/Max Temperature: 20/45 Celsius Lifetime Min/Max Temperature: 21/74 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: 1/85 Celsius Temperature History Size (Index): 128 (13) Index Estimated Time Temperature Celsius 14 2017-04-08 12:37 21 ** 15 2017-04-08 12:38 21 ** 16 2017-04-08 12:39 22 *** 17 2017-04-08 12:40 22 *** 18 2017-04-08 12:41 23 **** 19 2017-04-08 12:42 23 **** 20 2017-04-08 12:43 24 ***** 21 2017-04-08 12:44 25 ****** 22 2017-04-08 12:45 25 ****** 23 2017-04-08 12:46 26 ******* 24 2017-04-08 12:47 26 ******* 25 2017-04-08 12:48 26 ******* 26 2017-04-08 12:49 27 ******** 27 2017-04-08 12:50 27 ******** 28 2017-04-08 12:51 27 ******** 29 2017-04-08 12:52 28 ********* 30 2017-04-08 12:53 28 ********* 31 2017-04-08 12:54 29 ********** 32 2017-04-08 12:55 29 ********** 33 2017-04-08 12:56 30 *********** ... ..( 2 skipped). .. *********** 36 2017-04-08 12:59 30 *********** 37 2017-04-08 13:00 31 ************ ... ..( 2 skipped). .. ************ 40 2017-04-08 13:03 31 ************ 41 2017-04-08 13:04 32 ************* 42 2017-04-08 13:05 32 ************* 43 2017-04-08 13:06 32 ************* 44 2017-04-08 13:07 33 ************** ... ..( 2 skipped). .. ************** 47 2017-04-08 13:10 33 ************** 48 2017-04-08 13:11 34 *************** ... ..( 4 skipped). .. *************** 53 2017-04-08 13:16 34 *************** 54 2017-04-08 13:17 35 **************** 55 2017-04-08 13:18 35 **************** 56 2017-04-08 13:19 36 ***************** 57 2017-04-08 13:20 36 ***************** 58 2017-04-08 13:21 36 ***************** 59 2017-04-08 13:22 37 ****************** 60 2017-04-08 13:23 37 ****************** 61 2017-04-08 13:24 37 ****************** 62 2017-04-08 13:25 36 ***************** 63 2017-04-08 13:26 37 ****************** 64 2017-04-08 13:27 37 ****************** 65 2017-04-08 13:28 36 ***************** 66 2017-04-08 13:29 36 ***************** 67 2017-04-08 13:30 37 ****************** ... ..( 2 skipped). .. ****************** 70 2017-04-08 13:33 37 ****************** 71 2017-04-08 13:34 36 ***************** 72 2017-04-08 13:35 37 ****************** 73 2017-04-08 13:36 36 ***************** 74 2017-04-08 13:37 37 ****************** 75 2017-04-08 13:38 36 ***************** ... ..( 2 skipped). .. ***************** 78 2017-04-08 13:41 36 ***************** 79 2017-04-08 13:42 37 ****************** 80 2017-04-08 13:43 37 ****************** 81 2017-04-08 13:44 37 ****************** 82 2017-04-08 13:45 38 ******************* 83 2017-04-08 13:46 39 ******************** 84 2017-04-08 13:47 40 ********************* 85 2017-04-08 13:48 39 ******************** 86 2017-04-08 13:49 39 ******************** 87 2017-04-08 13:50 39 ******************** 88 2017-04-08 13:51 38 ******************* 89 2017-04-08 13:52 39 ******************** 90 2017-04-08 13:53 39 ******************** 91 2017-04-08 13:54 40 ********************* 92 2017-04-08 13:55 40 ********************* 93 2017-04-08 13:56 41 ********************** ... ..( 2 skipped). .. ********************** 96 2017-04-08 13:59 41 ********************** 97 2017-04-08 14:00 42 *********************** ... ..( 5 skipped). .. *********************** 103 2017-04-08 14:06 42 *********************** 104 2017-04-08 14:07 43 ************************ ... ..( 4 skipped). .. ************************ 109 2017-04-08 14:12 43 ************************ 110 2017-04-08 14:13 42 *********************** 111 2017-04-08 14:14 43 ************************ ... ..( 17 skipped). .. ************************ 1 2017-04-08 14:32 43 ************************ 2 2017-04-08 14:33 44 ************************* ... ..( 2 skipped). .. ************************* 5 2017-04-08 14:36 44 ************************* 6 2017-04-08 14:37 45 ************************** 7 2017-04-08 14:38 45 ************************** 8 2017-04-08 14:39 44 ************************* ... ..( 4 skipped). .. ************************* 13 2017-04-08 14:44 44 ************************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 27 Command failed due to ICRC error 0x0002 2 27 R_ERR response for data FIS 0x0003 2 27 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x8000 4 8280 Vendor specific