/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.8.0-29-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar Z5K500 Device Model: HGST HTS545050A7E380 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: GG2OACA0 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Nov 25 19:03:38 2020 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 108) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 077 062 - 0 2 Throughput_Performance P-S--K 198 100 040 - 120 3 Spin_Up_Time PO---K 217 100 033 - 1 4 Start_Stop_Count -O--CK 097 097 000 - 5572 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 32 (0 4) 7 Seek_Error_Rate POSR-K 100 100 067 - 0 8 Seek_Time_Performance P-S--K 115 100 040 - 34 9 Power_On_Hours -O--CK 072 072 000 - 12668 10 Spin_Retry_Count PO--CK 100 100 060 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 5281 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 001 000 - 19576559259434 188 Command_Timeout -O--CK 100 099 000 - 2658672508946 190 Airflow_Temperature_Cel -O---K 070 047 045 - 30 (Min/Max 20/30) 191 G-Sense_Error_Rate -O--CK 080 080 000 - 5193 192 Power-Off_Retract_Count -O--CK 099 099 000 - 21889358 193 Load_Cycle_Count -O--CK 059 059 000 - 416926 196 Reallocated_Event_Count -O--CK 100 100 000 - 2 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 2 223 Load_Retry_Count -O-R-K 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 20268 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 20268 [3] occurred at disk power-on lifetime: 11192 hours (466 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 3a 38 5f 80 0a 00 Error: WP at LBA = 0x3a385f80 = 976772992 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 80 00 10 00 00 39 8d 95 00 40 00 04:28:36.985 WRITE FPDMA QUEUED 61 00 80 00 08 00 00 39 8d 94 80 40 00 04:28:36.984 WRITE FPDMA QUEUED 61 00 80 00 00 00 00 39 8d 94 00 40 00 04:28:36.983 WRITE FPDMA QUEUED 61 00 80 00 f0 00 00 39 8d 93 80 40 00 04:28:36.982 WRITE FPDMA QUEUED 61 00 80 00 e8 00 00 39 8d 93 00 40 00 04:28:36.981 WRITE FPDMA QUEUED Error 20267 [2] occurred at disk power-on lifetime: 11192 hours (466 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 3a 38 5f 80 0a 00 Error: WP at LBA = 0x3a385f80 = 976772992 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 80 00 b8 00 00 39 7b 62 80 40 00 04:28:25.592 WRITE FPDMA QUEUED 61 00 80 00 b0 00 00 39 7b 62 00 40 00 04:28:25.591 WRITE FPDMA QUEUED 61 00 80 00 a8 00 00 39 7b 61 80 40 00 04:28:25.590 WRITE FPDMA QUEUED 61 00 80 00 a0 00 00 39 7b 61 00 40 00 04:28:25.587 WRITE FPDMA QUEUED 61 00 80 00 98 00 00 39 7b 60 80 40 00 04:28:25.586 WRITE FPDMA QUEUED Error 20266 [1] occurred at disk power-on lifetime: 11192 hours (466 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 3a 38 5f 80 0a 00 Error: WP at LBA = 0x3a385f80 = 976772992 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 80 00 e0 00 00 39 6d eb 80 40 00 04:28:17.182 WRITE FPDMA QUEUED 61 00 80 00 d8 00 00 39 6d eb 00 40 00 04:28:17.181 WRITE FPDMA QUEUED 61 00 80 00 d0 00 00 39 6d ea 80 40 00 04:28:17.180 WRITE FPDMA QUEUED 61 00 80 00 c8 00 00 39 6d ea 00 40 00 04:28:17.179 WRITE FPDMA QUEUED 61 00 80 00 c0 00 00 39 6d e9 80 40 00 04:28:17.178 WRITE FPDMA QUEUED Error 20265 [0] occurred at disk power-on lifetime: 11192 hours (466 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 3a 38 5d 58 0a 00 Error: WP at LBA = 0x3a385d58 = 976772440 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 80 00 20 00 00 39 5b 6d 00 40 00 04:28:05.889 WRITE FPDMA QUEUED 61 00 80 00 18 00 00 39 5b 6c 80 40 00 04:28:05.888 WRITE FPDMA QUEUED 61 00 80 00 10 00 00 39 5b 6c 00 40 00 04:28:05.887 WRITE FPDMA QUEUED 61 00 80 00 08 00 00 39 5b 6b 80 40 00 04:28:05.886 WRITE FPDMA QUEUED 61 00 80 00 00 00 00 39 5b 6b 00 40 00 04:28:05.885 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 12385 - # 2 Short offline Completed without error 00% 12227 - # 3 Short offline Completed without error 00% 12168 - # 4 Short offline Completed without error 00% 11986 - # 5 Short offline Completed without error 00% 11626 - # 6 Short offline Aborted by host 90% 11601 - # 7 Short offline Completed without error 00% 11601 - # 8 Extended offline Completed without error 00% 11599 - # 9 Short offline Completed without error 00% 11594 - #10 Extended offline Aborted by host 90% 11210 - #11 Short offline Completed without error 00% 11181 - #12 Short offline Completed: read failure 90% 10912 79355464 #13 Short offline Completed: read failure 90% 10912 79355464 #14 Short offline Completed: read failure 90% 10912 79355464 #15 Extended offline Completed: read failure 90% 10912 79355464 #16 Short offline Completed: read failure 90% 10910 79355464 #17 Short offline Completed: read failure 90% 10910 79355464 #18 Short offline Completed: read failure 90% 10910 79355464 #19 Short offline Completed: read failure 90% 10899 72412904 8 of 8 failed self-tests are outdated by newer successful extended offline self-test # 8 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 20/30 Celsius Lifetime Min/Max Temperature: 2/53 Celsius Specified Max Operating Temperature: 32 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (33) Index Estimated Time Temperature Celsius 34 2020-11-25 16:56 24 ***** ... ..( 5 skipped). .. ***** 40 2020-11-25 17:02 24 ***** 41 2020-11-25 17:03 ? - 42 2020-11-25 17:04 15 - 43 2020-11-25 17:05 17 - 44 2020-11-25 17:06 18 - 45 2020-11-25 17:07 19 - 46 2020-11-25 17:08 19 - 47 2020-11-25 17:09 20 * 48 2020-11-25 17:10 20 * 49 2020-11-25 17:11 21 ** 50 2020-11-25 17:12 22 *** 51 2020-11-25 17:13 22 *** 52 2020-11-25 17:14 23 **** 53 2020-11-25 17:15 24 ***** 54 2020-11-25 17:16 24 ***** 55 2020-11-25 17:17 24 ***** 56 2020-11-25 17:18 25 ****** 57 2020-11-25 17:19 25 ****** 58 2020-11-25 17:20 ? - 59 2020-11-25 17:21 20 * 60 2020-11-25 17:22 20 * 61 2020-11-25 17:23 20 * 62 2020-11-25 17:24 21 ** 63 2020-11-25 17:25 22 *** 64 2020-11-25 17:26 22 *** 65 2020-11-25 17:27 23 **** 66 2020-11-25 17:28 23 **** 67 2020-11-25 17:29 24 ***** ... ..( 9 skipped). .. ***** 77 2020-11-25 17:39 24 ***** 78 2020-11-25 17:40 25 ****** ... ..( 2 skipped). .. ****** 81 2020-11-25 17:43 25 ****** 82 2020-11-25 17:44 26 ******* ... ..( 5 skipped). .. ******* 88 2020-11-25 17:50 26 ******* 89 2020-11-25 17:51 27 ******** 90 2020-11-25 17:52 27 ******** 91 2020-11-25 17:53 27 ******** 92 2020-11-25 17:54 26 ******* ... ..( 9 skipped). .. ******* 102 2020-11-25 18:04 26 ******* 103 2020-11-25 18:05 27 ******** 104 2020-11-25 18:06 28 ********* ... ..( 3 skipped). .. ********* 108 2020-11-25 18:10 28 ********* 109 2020-11-25 18:11 29 ********** ... ..( 2 skipped). .. ********** 112 2020-11-25 18:14 29 ********** 113 2020-11-25 18:15 30 *********** 114 2020-11-25 18:16 29 ********** 115 2020-11-25 18:17 30 *********** 116 2020-11-25 18:18 30 *********** 117 2020-11-25 18:19 30 *********** 118 2020-11-25 18:20 29 ********** 119 2020-11-25 18:21 30 *********** 120 2020-11-25 18:22 29 ********** ... ..( 28 skipped). .. ********** 21 2020-11-25 18:51 29 ********** 22 2020-11-25 18:52 30 *********** 23 2020-11-25 18:53 29 ********** 24 2020-11-25 18:54 30 *********** 25 2020-11-25 18:55 29 ********** 26 2020-11-25 18:56 30 *********** 27 2020-11-25 18:57 29 ********** 28 2020-11-25 18:58 30 *********** 29 2020-11-25 18:59 29 ********** 30 2020-11-25 19:00 30 *********** ... ..( 2 skipped). .. *********** 33 2020-11-25 19:03 30 *********** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 4982 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 18 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS