/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Raptor Device Model: WDC WD360GD-00FLA2 Serial Number: -- Firmware Version: 31.08F31 User Capacity: 37,015,338,496 bytes [37.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-6 (minor revision not indicated) Local Time is: Wed Apr 25 21:29:23 2018 +06 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Unknown SCT Status format version 1, should be 2 or 3. Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 957) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 21) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x001f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 200 200 051 - 0 3 Spin_Up_Time POS--- 113 112 021 - 4891 4 Start_Stop_Count -O--CK 091 091 040 - 9106 5 Reallocated_Sector_Ct PO--CK 198 198 140 - 24 7 Seek_Error_Rate PO-R-- 100 253 051 - 0 9 Power_On_Hours -O--CK 062 062 000 - 27975 10 Spin_Retry_Count PO--C- 100 100 051 - 0 11 Calibration_Retry_Count PO--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 092 092 000 - 8473 194 Temperature_Celsius -O---K 116 090 000 - 34 196 Reallocated_Event_Count -O--CK 196 196 000 - 4 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable -O--C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 253 000 - 7079 200 Multi_Zone_Error_Rate P--R-- 200 179 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning Read SMART Log Directory failed: scsi error badly formed scsi parameters General Purpose Log Directory not supported SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 ATA Error Count: 1 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 occurred at disk power-on lifetime: 1071 hours (44 days + 15 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 a8 40 7e e0 Error: UNC at LBA = 0x007e40a8 = 8274088 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 78 40 7e 00 00 00:29:18.650 READ DMA c8 00 00 78 3f 7e 00 00 00:29:18.650 READ DMA c8 00 00 78 3e 7e 00 00 00:29:18.650 READ DMA c8 00 00 78 3d 7e 00 00 00:29:18.650 READ DMA c8 00 00 78 3c 7e 00 00 00:29:18.650 READ DMA SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 467 - # 2 Short offline Completed without error 00% 937 - # 3 Extended offline Aborted by host 90% 937 - # 4 Short offline Aborted by host 90% 937 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Unknown SCT Status format version 1, should be 2 or 3. Unknown SCT Status format version 1, should be 2 or 3. SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) not supported