/dev/nvme0n1 smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-90-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: Samsung SSD 980 PRO 500GB Serial Number: -- Firmware Version: 2B2QGXA7 PCI Vendor/Subsystem ID: 0x144d IEEE OUI Identifier: 0x002538 Total NVM Capacity: 500,107,862,016 [500 GB] Unallocated NVM Capacity: 0 Controller ID: 6 Number of Namespaces: 1 Namespace 1 Size/Capacity: 500,107,862,016 [500 GB] Namespace 1 Utilization: 21,853,315,072 [21.8 GB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 002538 ... Local Time is: Wed Nov 17 15:05:43 2021 EET Firmware Updates (0x16): 3 Slots, no Reset required Optional Admin Commands (0x0017): Security Format Frmw_DL Self_Test Optional NVM Commands (0x0057): Comp Wr_Unc DS_Mngmt Sav/Sel_Feat Timestmp Maximum Data Transfer Size: 128 Pages Warning Comp. Temp. Threshold: 82 Celsius Critical Comp. Temp. Threshold: 85 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 8.49W - - 0 0 0 0 0 0 1 + 4.48W - - 1 1 1 1 0 200 2 + 3.18W - - 2 2 2 2 0 1000 3 - 0.0400W - - 3 3 3 3 2000 1200 4 - 0.0050W - - 4 4 4 4 500 9500 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 0 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02) Critical Warning: 0x00 Temperature: 35 Celsius Available Spare: 100% Available Spare Threshold: 10% Percentage Used: 0% Data Units Read: 7,993 [4.09 GB] Data Units Written: 49,423 [25.3 GB] Host Read Commands: 104,243 Host Write Commands: 177,255 Controller Busy Time: 1 Power Cycles: 3 Power On Hours: 0 Unsafe Shutdowns: 0 Media and Data Integrity Errors: 0 Error Information Log Entries: 0 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Temperature Sensor 1: 35 Celsius Temperature Sensor 2: 44 Celsius Error Information (NVMe Log 0x01, max 64 entries) No Errors Logged /dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-90-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Gold Device Model: WDC WD2005FBYZ-01YCBB3 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: RR09 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Nov 17 15:05:43 2021 EET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Disabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 218) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x203d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 253 051 - 0 3 Spin_Up_Time POS--K 100 253 021 - 0 4 Start_Stop_Count -O--CK 100 100 000 - 2 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 1 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 2 16 Unknown_Attribute -O---K 000 200 000 - 67886 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 200 200 000 - 0 193 Load_Cycle_Count -O--CK 200 200 000 - 2 194 Temperature_Celsius -O---K 112 112 000 - 35 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0a GPL R/W 8 Device Statistics Notification 0x0c GPL R/O 113 Pending Defects log 0x0d GPL,SL R/O 8 LPS Mis-alignment log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x24 GPL R/O 192 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xb6 GPL,SL VS 16 Device vendor specific log 0xb7 GPL,SL VS 39 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 22/35 Celsius Lifetime Min/Max Temperature: 22/35 Celsius Specified Max Operating Temperature: 60 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (87) Index Estimated Time Temperature Celsius 88 2021-11-17 07:08 ? - ... ..(389 skipped). .. - 0 2021-11-17 13:38 ? - 1 2021-11-17 13:39 22 *** 2 2021-11-17 13:40 ? - 3 2021-11-17 13:41 22 *** 4 2021-11-17 13:42 22 *** 5 2021-11-17 13:43 23 **** 6 2021-11-17 13:44 23 **** 7 2021-11-17 13:45 25 ****** 8 2021-11-17 13:46 25 ****** 9 2021-11-17 13:47 25 ****** 10 2021-11-17 13:48 27 ******** 11 2021-11-17 13:49 27 ******** 12 2021-11-17 13:50 27 ******** 13 2021-11-17 13:51 28 ********* 14 2021-11-17 13:52 28 ********* 15 2021-11-17 13:53 29 ********** 16 2021-11-17 13:54 29 ********** 17 2021-11-17 13:55 30 *********** ... ..( 4 skipped). .. *********** 22 2021-11-17 14:00 30 *********** 23 2021-11-17 14:01 31 ************ ... ..( 3 skipped). .. ************ 27 2021-11-17 14:05 31 ************ 28 2021-11-17 14:06 32 ************* ... ..( 2 skipped). .. ************* 31 2021-11-17 14:09 32 ************* 32 2021-11-17 14:10 33 ************** ... ..( 4 skipped). .. ************** 37 2021-11-17 14:15 33 ************** 38 2021-11-17 14:16 34 *************** ... ..( 26 skipped). .. *************** 65 2021-11-17 14:43 34 *************** 66 2021-11-17 14:44 35 **************** ... ..( 20 skipped). .. **************** 87 2021-11-17 15:05 35 **************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 2 -D- Lifetime Power-On Resets 0x01 0x010 4 1 -D- Power-on Hours 0x01 0x018 6 0 -D- Logical Sectors Written 0x01 0x020 6 0 -D- Number of Write Commands 0x01 0x028 6 67886 -D- Logical Sectors Read 0x01 0x030 6 1867 -D- Number of Read Commands 0x01 0x038 6 3600000 -D- Date and Time TimeStamp 0x01 0x048 2 - ND- Workload Utilization 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 1 -D- Spindle Motor Power-on Hours 0x03 0x010 4 1 -D- Head Flying Hours 0x03 0x018 4 3 -D- Head Load Events 0x03 0x020 4 0 -D- Number of Reallocated Logical Sectors 0x03 0x028 4 0 -D- Read Recovery Attempts 0x03 0x030 4 0 -D- Number of Mechanical Start Failures 0x03 0x038 4 0 -D- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 0 -D- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 -D- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 -D- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 35 -D- Current Temperature 0x05 0x010 1 - -D- Average Short Term Temperature 0x05 0x018 1 - -D- Average Long Term Temperature 0x05 0x020 1 36 -D- Highest Temperature 0x05 0x028 1 28 -D- Lowest Temperature 0x05 0x030 1 - -D- Highest Average Short Term Temperature 0x05 0x038 1 - -D- Lowest Average Short Term Temperature 0x05 0x040 1 - -D- Highest Average Long Term Temperature 0x05 0x048 1 - -D- Lowest Average Long Term Temperature 0x05 0x050 4 0 -D- Time in Over-Temperature 0x05 0x058 1 60 -D- Specified Maximum Operating Temperature 0x05 0x060 4 0 -D- Time in Under-Temperature 0x05 0x068 1 0 -D- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 16 -D- Number of Hardware Resets 0x06 0x010 4 10 -D- Number of ASR Events 0x06 0x018 4 0 -D- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 10 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 16 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 0 Vendor specific