/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.15.0-33-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Silicon Motion based SSDs Device Model: ADATA SU800 Serial Number: -- LU WWN Device Id: 5 707c18 ... Firmware Version: R0918B User Capacity: 1,024,209,543,168 bytes [1.02 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jun 13 06:49:42 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Disabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown (0xe001) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 60) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 1) minutes. SCT capabilities: (0x0035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate ------ 100 100 000 - 0 5 Reallocated_Sector_Ct ------ 100 100 000 - 0 9 Power_On_Hours ------ 100 100 000 - 11257 12 Power_Cycle_Count ------ 100 100 000 - 2626 160 Uncorrectable_Error_Cnt ------ 100 100 000 - 0 161 Valid_Spare_Block_Cnt ------ 100 100 000 - 38 163 Initial_Bad_Block_Count ------ 100 100 000 - 16 164 Total_Erase_Count ------ 100 100 000 - 53635 165 Max_Erase_Count ------ 100 100 000 - 105 166 Min_Erase_Count ------ 100 100 000 - 4 167 Average_Erase_Count ------ 100 100 000 - 40 168 Max_Erase_Count_of_Spec ------ 100 100 000 - 1000 169 Remaining_Lifetime_Perc ------ 100 100 000 - 96 175 Program_Fail_Count_Chip ------ 100 100 000 - 0 176 Erase_Fail_Count_Chip ------ 100 100 000 - 0 177 Wear_Leveling_Count ------ 100 100 050 - 70 178 Runtime_Invalid_Blk_Cnt ------ 100 100 000 - 0 181 Program_Fail_Cnt_Total ------ 100 100 000 - 0 182 Erase_Fail_Count_Total ------ 100 100 000 - 0 192 Power-Off_Retract_Count ------ 100 100 000 - 155 194 Temperature_Celsius ------ 100 100 000 - 31 195 Hardware_ECC_Recovered ------ 100 100 000 - 0 196 Reallocated_Event_Count ------ 100 100 016 - 0 197 Current_Pending_Sector ------ 100 100 000 - 0 198 Offline_Uncorrectable ------ 100 100 000 - 0 199 UDMA_CRC_Error_Count ------ 100 100 050 - 99 232 Available_Reservd_Space ------ 100 100 000 - 100 241 Host_Writes_32MiB ------ 100 100 000 - 1359589 242 Host_Reads_32MiB ------ 100 100 000 - 741691 245 TLC_Writes_32MiB ------ 100 100 000 - 858160 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x0a GPL R/W 8 Device Statistics Notification 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 88 Current Device Internal Status Data log 0x25 GPL R/O 64 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Conveyance offline Completed without error 00% 1448 - # 2 Extended offline Completed without error 00% 1439 - # 3 Short offline Completed without error 00% 1439 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 7 0 65535 Read_scanning was completed without error Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 0 (0x0000) Device State: Active (0) Current Temperature: 0 Celsius Power Cycle Min/Max Temperature: -1/ 0 Celsius Lifetime Min/Max Temperature: 0/58 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/100 Celsius Min/Max Temperature Limit: 0/100 Celsius Temperature History Size (Index): 128 (45) Index Estimated Time Temperature Celsius 46 2022-06-13 04:42 46 *************************** 47 2022-06-13 04:43 45 ************************** 48 2022-06-13 04:44 45 ************************** 49 2022-06-13 04:45 46 *************************** ... ..( 80 skipped). .. *************************** 2 2022-06-13 06:06 46 *************************** 3 2022-06-13 06:07 45 ************************** ... ..( 41 skipped). .. ************************** 45 2022-06-13 06:49 45 ************************** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 2626 --- Lifetime Power-On Resets 0x01 0x010 4 11257 --- Power-on Hours 0x01 0x018 6 3202722874 --- Logical Sectors Written 0x01 0x020 6 882885691 --- Number of Write Commands 0x01 0x028 6 1362826510 --- Logical Sectors Read 0x01 0x030 6 660866391 --- Number of Read Commands 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 156 --- Resets Between Cmd Acceptance and Completion 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 7834 --- Number of Hardware Resets 0x06 0x018 4 99 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 4 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.15.0-33-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Crucial/Micron RealSSD m4/C400/P400 Device Model: M4-CT064M4SSD2 Serial Number: -- LU WWN Device Id: 5 00a075 ... Firmware Version: 070H User Capacity: 64,023,257,088 bytes [64.0 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jun 13 06:49:42 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 295) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 4) minutes. Conveyance self-test routine recommended polling time: ( 3) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 050 - 0 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 001 - 47183 12 Power_Cycle_Count -O--CK 100 100 001 - 10503 170 Grown_Failing_Block_Ct PO--CK 100 100 010 - 0 171 Program_Fail_Count -O--CK 100 100 001 - 0 172 Erase_Fail_Count -O--CK 100 100 001 - 0 173 Wear_Leveling_Count PO--CK 067 067 010 - 991 174 Unexpect_Power_Loss_Ct -O--CK 100 100 001 - 644 181 Non4k_Aligned_Access -O---K 100 100 001 - 5934 1567 4366 183 SATA_Iface_Downshift -O--CK 100 100 001 - 0 184 End-to-End_Error PO--CK 100 100 050 - 0 187 Reported_Uncorrect -O--CK 100 100 001 - 0 188 Command_Timeout -O--CK 100 100 001 - 0 189 Factory_Bad_Block_Ct -OSR-- 100 100 001 - 70 194 Temperature_Celsius -O---K 100 100 000 - 0 195 Hardware_ECC_Recovered -O-RCK 100 100 001 - 0 196 Reallocated_Event_Count -O--CK 100 100 001 - 0 197 Current_Pending_Sector -O--CK 100 100 001 - 0 198 Offline_Uncorrectable ----CK 100 100 001 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 001 - 721 202 Perc_Rated_Life_Used ---RC- 067 067 001 - 33 206 Write_Error_Rate -OSR-- 100 100 001 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 16383 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 255 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 3449 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL VS 2000 Device vendor specific log 0xa0 SL VS 208 Device vendor specific log 0xa1-0xbf GPL,SL VS 1 Device vendor specific log 0xc0 GPL VS 80 Device vendor specific log 0xc1-0xdf GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (16383 sectors) No Errors Logged SMART Extended Self-test Log size 3449 not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Vendor (0xff) Completed without error 00% 44780 - # 2 Vendor (0xff) Completed without error 00% 44770 - # 3 Vendor (0xff) Completed without error 00% 44755 - # 4 Vendor (0xff) Completed without error 00% 44641 - # 5 Vendor (0xff) Completed without error 00% 44611 - # 6 Vendor (0xff) Completed without error 00% 44599 - # 7 Vendor (0xff) Completed without error 00% 44569 - # 8 Vendor (0xff) Completed without error 00% 44537 - # 9 Vendor (0xff) Completed without error 00% 44515 - #10 Vendor (0xff) Completed without error 00% 44482 - #11 Vendor (0xff) Completed without error 00% 44473 - #12 Vendor (0xff) Completed without error 00% 44444 - #13 Vendor (0xff) Completed without error 00% 44393 - #14 Vendor (0xff) Completed without error 00% 44351 - #15 Vendor (0xff) Completed without error 00% 44324 - #16 Vendor (0xff) Completed without error 00% 44286 - #17 Vendor (0xff) Completed without error 00% 44265 - #18 Vendor (0xff) Completed without error 00% 44210 - #19 Vendor (0xff) Completed without error 00% 44074 - #20 Vendor (0xff) Completed without error 00% 44045 - #21 Vendor (0xff) Completed without error 00% 43766 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 0 Celsius Power Cycle Min/Max Temperature: --/ 0 Celsius Lifetime Min/Max Temperature: --/ 0 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: -5/75 Celsius Temperature History Size (Index): 478 (434) Index Estimated Time Temperature Celsius 435 2022-06-09 23:10 ? - ... ..(476 skipped). .. - 434 2022-06-13 06:40 ? - SCT Error Recovery Control: Read: 40 (4.0 seconds) Write: 40 (4.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 10503 --- Lifetime Power-On Resets 0x01 0x010 4 47183 --- Power-on Hours 0x01 0x018 6 82236436859 --- Logical Sectors Written 0x01 0x020 6 1671015222 --- Number of Write Commands 0x01 0x028 6 120391812720 --- Logical Sectors Read 0x01 0x030 6 2015096846 --- Number of Read Commands 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 0 --- Current Temperature 0x05 0x010 1 0 --- Average Short Term Temperature 0x05 0x018 1 0 --- Average Long Term Temperature 0x05 0x020 1 0 --- Highest Temperature 0x05 0x028 1 0 --- Lowest Temperature 0x05 0x030 1 0 --- Highest Average Short Term Temperature 0x05 0x038 1 0 --- Lowest Average Short Term Temperature 0x05 0x040 1 0 --- Highest Average Long Term Temperature 0x05 0x048 1 0 --- Lowest Average Long Term Temperature 0x05 0x050 4 - --- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 - --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 0 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 721 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 17 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET /dev/sdc smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.15.0-33-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital RE3 Serial ATA Device Model: WDC WD5002ABYS-01B1B0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 02.03B02 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Mon Jun 13 06:49:42 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 128 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9480) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 112) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 101 3 Spin_Up_Time POS--K 163 160 021 - 4841 4 Start_Stop_Count -O--CK 089 089 000 - 11742 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 040 040 000 - 44281 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 089 089 000 - 11045 192 Power-Off_Retract_Count -O--CK 199 199 000 - 925 193 Load_Cycle_Count -O--CK 197 197 000 - 11742 194 Temperature_Celsius -O---K 124 076 000 - 23 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 5032 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 65 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 65 [16] occurred at disk power-on lifetime: 39485 hours (1645 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 35 79 00 2a d0 40 00 Error: UNC at LBA = 0x3579002ad0 = 229663320784 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 58 00 00 21 01 4c 28 40 08 00:00:50.291 READ FPDMA QUEUED 60 00 08 00 50 00 00 0f 81 11 20 40 08 00:00:50.288 READ FPDMA QUEUED 60 00 08 00 48 00 00 0f 81 11 18 40 08 00:00:50.274 READ FPDMA QUEUED 60 00 18 00 18 00 00 35 2a 79 d0 40 08 00:00:50.260 READ FPDMA QUEUED 60 01 08 00 40 00 00 0f 80 09 00 40 08 00:00:50.259 READ FPDMA QUEUED Error 64 [15] occurred at disk power-on lifetime: 39485 hours (1645 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 1b e7 00 44 30 40 00 Error: UNC at LBA = 0x1be7004430 = 119839671344 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 10 00 00 1b 44 e7 30 40 08 00:00:59.190 READ FPDMA QUEUED 60 00 08 00 58 00 00 21 01 4c 28 40 08 00:00:59.167 READ FPDMA QUEUED 60 00 08 00 50 00 00 0f 81 11 20 40 08 00:00:59.164 READ FPDMA QUEUED 60 00 08 00 48 00 00 0f 81 11 18 40 08 00:00:59.150 READ FPDMA QUEUED 60 01 08 00 08 00 00 37 00 09 00 40 08 00:00:59.126 READ FPDMA QUEUED Error 63 [14] occurred at disk power-on lifetime: 11927 hours (496 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 17 3e 00 e7 62 40 00 Error: UNC at LBA = 0x173e00e762 = 99824494434 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 c0 00 00 17 e7 3d e8 40 00 04:32:51.990 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 04:32:51.990 READ LOG EXT 60 00 80 00 b8 00 00 17 e7 3d e8 40 00 04:32:49.633 READ FPDMA QUEUED 60 00 80 00 b0 00 00 17 e7 3d 68 40 00 04:32:49.633 READ FPDMA QUEUED 60 00 80 00 a8 00 00 17 e7 3c e8 40 00 04:32:49.632 READ FPDMA QUEUED Error 62 [13] occurred at disk power-on lifetime: 11927 hours (496 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 17 3e 00 e7 62 40 00 Error: UNC at LBA = 0x173e00e762 = 99824494434 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 b8 00 00 17 e7 3d e8 40 00 04:32:49.633 READ FPDMA QUEUED 60 00 80 00 b0 00 00 17 e7 3d 68 40 00 04:32:49.633 READ FPDMA QUEUED 60 00 80 00 a8 00 00 17 e7 3c e8 40 00 04:32:49.632 READ FPDMA QUEUED 60 00 80 00 a0 00 00 17 e7 3c 68 40 00 04:32:49.632 READ FPDMA QUEUED 60 00 80 00 98 00 00 17 e7 3b e8 40 00 04:32:49.632 READ FPDMA QUEUED Error 61 [12] occurred at disk power-on lifetime: 11922 hours (496 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 46 00 00 08 00 5e 00 40 00 Error: IDNF at LBA = 0x08005e00 = 134241792 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 38 00 00 06 40 27 30 40 00 03:45:50.052 READ FPDMA QUEUED 60 00 08 00 30 00 00 1b 1f 8b 88 40 00 03:45:50.052 READ FPDMA QUEUED 60 00 08 00 28 00 00 06 a5 ec 78 40 00 03:45:50.052 READ FPDMA QUEUED 60 00 08 00 20 00 00 06 5d b1 50 40 00 03:45:50.052 READ FPDMA QUEUED 60 00 08 00 18 00 00 06 40 2a e8 40 00 03:45:50.052 READ FPDMA QUEUED Error 60 [11] occurred at disk power-on lifetime: 11922 hours (496 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 08 00 5e 00 40 00 Error: IDNF at LBA = 0x08005e00 = 134241792 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 18 00 00 00 5e 08 00 40 00 03:44:08.151 WRITE FPDMA QUEUED 60 00 38 00 10 00 00 06 a0 ce 00 40 00 03:44:08.151 READ FPDMA QUEUED 60 00 08 00 08 00 00 06 40 2a e8 40 00 03:44:08.151 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 40 00 03:44:08.151 SET FEATURES [Enable write cache] ef 00 03 00 46 00 00 00 00 00 00 40 00 03:44:08.151 SET FEATURES [Set transfer mode] Error 59 [10] occurred at disk power-on lifetime: 11922 hours (496 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 06 f8 00 87 70 40 00 Error: UNC at LBA = 0x6f8008770 = 29930588016 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 48 00 10 00 00 06 a0 c5 b8 40 00 03:43:18.291 READ FPDMA QUEUED 60 00 28 00 08 00 00 06 87 f8 70 40 00 03:43:18.290 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 40 00 03:43:18.290 SET FEATURES [Enable write cache] ef 00 03 00 46 00 00 00 00 00 00 40 00 03:43:18.290 SET FEATURES [Set transfer mode] c6 00 00 00 10 00 00 00 00 00 00 40 00 03:43:18.290 SET MULTIPLE MODE Error 58 [9] occurred at disk power-on lifetime: 11922 hours (496 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 27 00 06 a5 00 a0 70 40 00 Error: UNC at LBA = 0x6a500a070 = 28538085488 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 10 00 00 06 a5 82 f8 40 00 03:38:52.740 READ FPDMA QUEUED 60 00 08 00 08 00 00 06 a0 a5 70 40 00 03:38:52.740 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 40 00 03:38:52.740 SET FEATURES [Enable write cache] ef 00 03 00 46 00 00 00 00 00 00 40 00 03:38:52.740 SET FEATURES [Set transfer mode] c6 00 00 00 10 00 00 00 00 00 00 40 00 03:38:52.740 SET MULTIPLE MODE SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Aborted by host 90% 39487 - # 2 Short offline Completed without error 00% 39487 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 23 Celsius Power Cycle Min/Max Temperature: 23/23 Celsius Lifetime Min/Max Temperature: 24/71 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (2) Index Estimated Time Temperature Celsius 3 2022-06-12 22:52 37 ****************** ... ..( 45 skipped). .. ****************** 49 2022-06-12 23:38 37 ****************** 50 2022-06-12 23:39 36 ***************** ... ..( 10 skipped). .. ***************** 61 2022-06-12 23:50 36 ***************** 62 2022-06-12 23:51 37 ****************** ... ..( 26 skipped). .. ****************** 89 2022-06-13 00:18 37 ****************** 90 2022-06-13 00:19 ? - 91 2022-06-13 00:20 23 **** 92 2022-06-13 00:21 37 ****************** ... ..(182 skipped). .. ****************** 275 2022-06-13 03:24 37 ****************** 276 2022-06-13 03:25 36 ***************** ... ..( 52 skipped). .. ***************** 329 2022-06-13 04:18 36 ***************** 330 2022-06-13 04:19 37 ****************** ... ..( 31 skipped). .. ****************** 362 2022-06-13 04:51 37 ****************** 363 2022-06-13 04:52 ? - 364 2022-06-13 04:53 23 **** 365 2022-06-13 04:54 24 ***** 366 2022-06-13 04:55 25 ****** 367 2022-06-13 04:56 25 ****** 368 2022-06-13 04:57 26 ******* 369 2022-06-13 04:58 26 ******* 370 2022-06-13 04:59 27 ******** 371 2022-06-13 05:00 28 ********* 372 2022-06-13 05:01 29 ********** 373 2022-06-13 05:02 29 ********** 374 2022-06-13 05:03 29 ********** 375 2022-06-13 05:04 30 *********** 376 2022-06-13 05:05 30 *********** 377 2022-06-13 05:06 30 *********** 378 2022-06-13 05:07 31 ************ 379 2022-06-13 05:08 31 ************ 380 2022-06-13 05:09 32 ************* 381 2022-06-13 05:10 32 ************* 382 2022-06-13 05:11 32 ************* 383 2022-06-13 05:12 33 ************** ... ..( 3 skipped). .. ************** 387 2022-06-13 05:16 33 ************** 388 2022-06-13 05:17 34 *************** ... ..( 3 skipped). .. *************** 392 2022-06-13 05:21 34 *************** 393 2022-06-13 05:22 ? - 394 2022-06-13 05:23 26 ******* 395 2022-06-13 05:24 26 ******* 396 2022-06-13 05:25 26 ******* 397 2022-06-13 05:26 27 ******** 398 2022-06-13 05:27 28 ********* 399 2022-06-13 05:28 29 ********** 400 2022-06-13 05:29 29 ********** 401 2022-06-13 05:30 30 *********** 402 2022-06-13 05:31 30 *********** 403 2022-06-13 05:32 30 *********** 404 2022-06-13 05:33 31 ************ 405 2022-06-13 05:34 32 ************* 406 2022-06-13 05:35 32 ************* 407 2022-06-13 05:36 33 ************** ... ..( 2 skipped). .. ************** 410 2022-06-13 05:39 33 ************** 411 2022-06-13 05:40 34 *************** ... ..( 4 skipped). .. *************** 416 2022-06-13 05:45 34 *************** 417 2022-06-13 05:46 35 **************** ... ..( 3 skipped). .. **************** 421 2022-06-13 05:50 35 **************** 422 2022-06-13 05:51 36 ***************** ... ..( 4 skipped). .. ***************** 427 2022-06-13 05:56 36 ***************** 428 2022-06-13 05:57 37 ****************** ... ..( 51 skipped). .. ****************** 2 2022-06-13 06:49 37 ****************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x8000 4 47 Vendor specific /dev/sdd smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.15.0-33-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SanDisk based SSDs Device Model: SanDisk SDSSDP064G Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: 3.2.0 User Capacity: 63,023,063,040 bytes [63.0 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 1.8 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon Jun 13 06:49:43 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 11) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O---- 100 100 000 - 0 9 Power_On_Hours -O---- 100 100 000 - 24623 12 Power_Cycle_Count -O---- 100 100 000 - 5100 165 Total_Write/Erase_Count -O---- 100 100 000 - 7466463 171 Program_Fail_Count -O---- 100 100 000 - 0 172 Erase_Fail_Count -O---- 100 100 000 - 0 173 Avg_Write/Erase_Count -O---- 100 100 000 - 1917 174 Unexpect_Power_Loss_Ct -O---- 100 100 000 - 293 187 Reported_Uncorrect -O---- 100 100 000 - 0 194 Temperature_Celsius -O---K 076 024 000 - 24 (Min/Max 15/53) 230 Perc_Write/Erase_Count -O---- 100 100 000 - 6390 232 Perc_Avail_Resrvd_Space PO---- 100 100 005 - 0 234 Perc_Write/Erase_Ct_BC -O---- 100 100 000 - 2492 241 Total_LBAs_Written -O---- 100 100 000 - 33696724769 242 Total_LBAs_Read -O---- 100 100 000 - 25866673802 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x03 GPL,SL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 GPL,SL R/O 1 SMART self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3 GPL,SL VS 1 Device vendor specific log 0xa6-0xa7 GPL,SL VS 255 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (16 sectors) Device Error Count: 4 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4 [3] occurred at disk power-on lifetime: 61166 hours (2548 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 45 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 44 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 43 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 42 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 41 3d+07:32:11.153 NOP [Abort queued commands] Error 3 [2] occurred at disk power-on lifetime: 61166 hours (2548 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 35 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 34 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 33 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 32 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 31 3d+07:32:11.153 NOP [Abort queued commands] Error 2 [1] occurred at disk power-on lifetime: 61166 hours (2548 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 25 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 24 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 23 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 22 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 21 3d+07:32:11.153 NOP [Abort queued commands] Error 1 [0] occurred at disk power-on lifetime: 43981 hours (1832 days + 13 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 15 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 14 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 13 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 12 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 11 3d+07:32:11.153 NOP [Abort queued commands] SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 17064 - # 2 Extended offline Completed without error 00% 13594 - # 3 Short offline Completed without error 00% 13594 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 24 --- Current Temperature 0x05 0x010 1 - --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 52 --- Highest Temperature 0x05 0x028 1 26 --- Lowest Temperature 0x05 0x030 1 40 --- Highest Average Short Term Temperature 0x05 0x038 1 40 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 95 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 63 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0001 2 0 Command failed due to ICRC error