/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.11.0-37-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" DT01ACA... Desktop HDD Device Model: TOSHIBA DT01ACA100 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: MS2OA750 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Oct 10 22:28:37 2021 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7847) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 131) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 140 140 054 - 75 3 Spin_Up_Time POS--- 126 126 024 - 184 (Average 181) 4 Start_Stop_Count -O--C- 099 099 000 - 6521 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 115 115 020 - 34 9 Power_On_Hours -O--C- 097 097 000 - 22885 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 3081 192 Power-Off_Retract_Count -O--CK 095 095 000 - 6588 193 Load_Cycle_Count -O--C- 095 095 000 - 6588 194 Temperature_Celsius -O---- 200 200 000 - 30 (Min/Max 8/45) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 48 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 51 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 51 [2] occurred at disk power-on lifetime: 10202 hours (425 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 31 00 00 16 7c c2 8f 06 00 Error: ICRC, ABRT at LBA = 0x167cc28f = 377275023 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 30 00 00 16 7c c2 90 46 ff 01:34:36.254 READ FPDMA QUEUED 60 00 80 00 10 00 00 16 7c c2 40 40 00 01:34:36.253 READ FPDMA QUEUED 60 00 80 00 08 00 00 16 7c c1 c0 40 00 01:34:36.186 READ FPDMA QUEUED 60 00 80 00 08 00 00 31 8b 56 00 40 00 01:34:36.160 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 00 00 01:34:36.160 SET FEATURES [Disable SATA feature] Error 50 [1] occurred at disk power-on lifetime: 10202 hours (425 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 31 00 00 16 7c 95 8f 06 00 Error: ICRC, ABRT at LBA = 0x167c958f = 377263503 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 30 00 00 16 7c 95 90 46 ff 01:34:29.723 READ FPDMA QUEUED 60 00 80 00 40 00 00 16 7c 95 40 40 00 01:34:29.722 READ FPDMA QUEUED 60 00 80 00 38 00 00 16 7c 94 c0 40 00 01:34:29.672 READ FPDMA QUEUED 60 00 28 00 30 00 00 16 88 2c 78 40 00 01:34:29.615 READ FPDMA QUEUED 60 00 02 00 28 00 00 00 20 cc b8 40 00 01:34:29.592 READ FPDMA QUEUED Error 49 [0] occurred at disk power-on lifetime: 10202 hours (425 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 61 00 00 16 7c 75 5f 06 00 Error: ICRC, ABRT at LBA = 0x167c755f = 377255263 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 60 00 00 16 7c 75 60 46 ff 01:34:25.650 READ FPDMA QUEUED 60 00 80 00 08 00 00 16 7c 75 40 40 00 01:34:25.649 READ FPDMA QUEUED 60 00 80 00 10 00 00 16 7c 74 c0 40 00 01:34:25.576 READ FPDMA QUEUED 60 00 80 00 08 00 00 31 8b 53 80 40 00 01:34:25.576 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 00 00 01:34:25.576 SET FEATURES [Disable SATA feature] Error 48 [3] occurred at disk power-on lifetime: 10202 hours (425 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 41 00 00 16 7c 2f 7f 06 00 Error: ICRC, ABRT at LBA = 0x167c2f7f = 377237375 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 40 00 00 16 7c 2f 80 46 ff 01:34:16.339 READ FPDMA QUEUED 60 00 80 00 10 00 00 16 7c 2f 40 40 00 01:34:16.338 READ FPDMA QUEUED 60 00 80 00 08 00 00 16 7c 2e c0 40 00 01:34:16.337 READ FPDMA QUEUED 60 00 80 00 30 00 00 16 7c 2e 40 40 00 01:34:16.261 READ FPDMA QUEUED 60 00 08 00 10 00 00 31 8b 52 f8 40 00 01:34:16.261 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 19/30 Celsius Lifetime Min/Max Temperature: 8/45 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (44) Index Estimated Time Temperature Celsius 45 2021-10-10 20:21 28 ********* 46 2021-10-10 20:22 29 ********** 47 2021-10-10 20:23 29 ********** 48 2021-10-10 20:24 28 ********* 49 2021-10-10 20:25 28 ********* 50 2021-10-10 20:26 29 ********** 51 2021-10-10 20:27 28 ********* 52 2021-10-10 20:28 29 ********** 53 2021-10-10 20:29 29 ********** 54 2021-10-10 20:30 29 ********** 55 2021-10-10 20:31 28 ********* 56 2021-10-10 20:32 29 ********** ... ..( 18 skipped). .. ********** 75 2021-10-10 20:51 29 ********** 76 2021-10-10 20:52 28 ********* ... ..( 3 skipped). .. ********* 80 2021-10-10 20:56 28 ********* 81 2021-10-10 20:57 29 ********** ... ..( 34 skipped). .. ********** 116 2021-10-10 21:32 29 ********** 117 2021-10-10 21:33 30 *********** ... ..( 10 skipped). .. *********** 0 2021-10-10 21:44 30 *********** 1 2021-10-10 21:45 29 ********** 2 2021-10-10 21:46 30 *********** 3 2021-10-10 21:47 30 *********** 4 2021-10-10 21:48 29 ********** 5 2021-10-10 21:49 30 *********** 6 2021-10-10 21:50 29 ********** ... ..( 28 skipped). .. ********** 35 2021-10-10 22:19 29 ********** 36 2021-10-10 22:20 30 *********** ... ..( 7 skipped). .. *********** 44 2021-10-10 22:28 30 *********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 3081 --- Lifetime Power-On Resets 0x01 0x010 4 22885 --- Power-on Hours 0x01 0x018 6 58601920404 --- Logical Sectors Written 0x01 0x020 6 773466557 --- Number of Write Commands 0x01 0x028 6 702858416861 --- Logical Sectors Read 0x01 0x030 6 1153401058 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 21363 --- Spindle Motor Power-on Hours 0x03 0x010 4 21363 --- Head Flying Hours 0x03 0x018 4 6588 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 814 --- Read Recovery Attempts 0x03 0x030 4 2 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 10 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 13596 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 30 --- Current Temperature 0x05 0x010 1 28 N-- Average Short Term Temperature 0x05 0x018 1 26 N-- Average Long Term Temperature 0x05 0x020 1 45 --- Highest Temperature 0x05 0x028 1 8 --- Lowest Temperature 0x05 0x030 1 41 N-- Highest Average Short Term Temperature 0x05 0x038 1 22 N-- Lowest Average Short Term Temperature 0x05 0x040 1 37 N-- Highest Average Long Term Temperature 0x05 0x048 1 24 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 35761 --- Number of Hardware Resets 0x06 0x010 4 24644 --- Number of ASR Events 0x06 0x018 4 48 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 15 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 15 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdc smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.11.0-37-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Apacer AS340 SSDs Device Model: Apacer AS340 120GB Serial Number: -- LU WWN Device Id: 5 02b2a2 ... Add. Product Id: mavlsata Firmware Version: V3.3 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Oct 10 22:28:39 2021 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Unavailable Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x35) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x00) Error logging NOT supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 1) minutes. Conveyance self-test routine recommended polling time: ( 1) minutes. SMART Attributes Data Structure revision number: 5 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours PO--CK 100 100 010 - 10542 12 Power_Cycle_Count PO--CK 100 100 010 - 1468 161 Unknown_Attribute PO--CK 100 100 010 - 0 164 Average_Erase_Count PO--CK 100 100 010 - 23687 165 Unknown_Attribute PO--CK 100 100 010 - 69 166 Later_Bad_Block_Count PO--CK 100 100 010 - 16 167 SSD_Protect_Mode PO--CK 100 100 010 - 52 176 Erase_Fail_Count_Chip PO--CK 100 100 010 - 0 177 Wear_Leveling_Count PO--CK 100 100 010 - 0 178 Used_Rsvd_Blk_Cnt_Chip PO--CK 100 100 010 - 0 192 Unexpect_Power_Loss_Ct PO--CK 100 100 010 - 0 194 Temperature_Celsius PO--CK 100 100 010 - 39 195 Hardware_ECC_Recovered PO--CK 100 100 010 - 0 199 UDMA_CRC_Error_Count PO--CK 100 100 010 - 0 241 Total_LBAs_Written PO--CK 100 100 010 - 9953 242 Total_LBAs_Read PO--CK 100 100 010 - 8564 243 Unknown_Attribute PO--CK 100 100 010 - 0 244 Unknown_Attribute PO--CK 100 100 010 - 0 250 Read_Error_Retry_Rate PO--CK 100 100 010 - 0 251 Unknown_Attribute PO--CK 100 100 010 - 0 252 Unknown_Attribute PO--CK 100 100 010 - 0 253 Unknown_Attribute PO--CK 100 100 010 - 0 254 Unknown_SSD_Attribute PO--CK 100 100 010 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x10 GPL,SL R/O 1 NCQ Command Error log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log not supported SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test Log not supported Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported