/dev/sda smartctl 6.6 2017-11-05 r4594 [i686-linux-4.19.0-8-686] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint M Device Model: SAMSUNG MP0402H Serial Number: -- Firmware Version: UC200-16 User Capacity: 40,007,761,920 bytes [40.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 T13/1532D revision 0 Local Time is: Sun Mar 29 23:00:25 2020 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 254 APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2400) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 40) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0 3 Spin_Up_Time POS--- 100 100 025 - 2624 4 Start_Stop_Count -O--CK 096 096 000 - 4973 5 Reallocated_Sector_Ct PO--CK 088 088 011 - 26 7 Seek_Error_Rate -OSR-- 100 100 000 - 0 8 Seek_Time_Performance --S--K 100 100 000 - 0 9 Power_On_Half_Minutes -O--CK 097 097 000 - 19199h+14m 10 Spin_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2561 191 G-Sense_Error_Rate -O--C- 047 047 000 - 539521 194 Temperature_Celsius -O---K 100 058 000 - 46 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 1716967 196 Reallocated_Event_Count -O--CK 071 071 000 - 64 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O--C- 100 100 000 - 0 223 Load_Retry_Count -O--C- 082 082 000 - 18412 225 Load_Cycle_Count -O--C- 001 001 000 - 2446636 255 Unknown_Attribute -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory not supported SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x06 SL R/O 2 SMART self-test log 0x80-0x9f SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 ATA Error Count: 9395 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 9395 occurred at disk power-on lifetime: 19140 hours (797 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 9f 4e 24 e0 Error: UNC at LBA = 0x00244e9f = 2379423 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c4 00 00 9f 4e 24 e0 00 05:11:03.563 READ MULTIPLE ca 00 18 4f 4a 00 e0 00 05:11:03.563 WRITE DMA ca 00 10 9f 3c fa e0 00 05:11:03.563 WRITE DMA ca 00 28 57 e7 8e e4 00 05:11:03.563 WRITE DMA ca 00 08 a2 49 ec e0 00 05:11:03.563 WRITE DMA Error 9394 occurred at disk power-on lifetime: 19140 hours (797 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 9f 4e 24 e0 Error: UNC at LBA = 0x00244e9f = 2379423 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 9f 4e 24 e0 00 05:10:33.875 READ DMA ca 00 10 bf f3 06 e0 00 05:10:33.875 WRITE DMA ca 00 08 c7 00 00 e0 00 05:10:33.875 WRITE DMA ca 00 08 7f aa 72 e1 00 05:10:33.875 WRITE DMA ca 00 18 8a 49 ec e0 00 05:10:33.875 WRITE DMA Error 9393 occurred at disk power-on lifetime: 19140 hours (797 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 9f 4e 24 e0 Error: UNC at LBA = 0x00244e9f = 2379423 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c4 00 00 9f 4e 24 e0 00 05:10:03.563 READ MULTIPLE ca 00 08 8f f2 19 e0 00 05:10:03.563 WRITE DMA ca 00 08 87 f2 19 e0 00 05:10:03.563 WRITE DMA ca 00 08 7f f2 19 e0 00 05:10:03.563 WRITE DMA ca 00 08 77 f2 19 e0 00 05:10:03.563 WRITE DMA Error 9392 occurred at disk power-on lifetime: 19140 hours (797 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 9f 4e 24 e0 Error: UNC at LBA = 0x00244e9f = 2379423 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 9f 4e 24 e0 00 05:09:33.875 READ DMA ca 00 08 77 f3 06 e0 00 05:09:33.875 WRITE DMA ca 00 08 4f 01 02 e0 00 05:09:33.875 WRITE DMA ca 00 10 3f 4a 00 e0 00 05:09:33.875 WRITE DMA ca 00 28 df e6 8e e4 00 05:09:33.875 WRITE DMA Error 9391 occurred at disk power-on lifetime: 19140 hours (797 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 9f 4e 24 e0 Error: UNC at LBA = 0x00244e9f = 2379423 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c4 00 00 9f 4e 24 e0 00 05:09:03.563 READ MULTIPLE ca 00 08 67 f3 06 e0 00 05:09:03.563 WRITE DMA ca 00 20 1f 4a 00 e0 00 05:09:03.563 WRITE DMA ca 00 30 9f e6 8e e4 00 05:09:03.563 WRITE DMA c5 00 08 72 49 ec e0 00 05:09:03.563 WRITE MULTIPLE SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported