/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST380815AS Serial Number: -- Firmware Version: 4.AAB User Capacity: 80 026 361 856 bytes [80,0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Tue Nov 10 22:32:54 2015 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 27) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 253 006 - 0 3 Spin_Up_Time PO---- 098 097 000 - 0 4 Start_Stop_Count -O--CK 096 096 020 - 4468 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 085 060 030 - 369747456 9 Power_On_Hours -O--CK 091 091 000 - 8065 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4437 187 Reported_Uncorrect -O--CK 050 050 000 - 50 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 058 050 045 - 42 (Min/Max 37/42) 194 Temperature_Celsius -O---K 042 050 000 - 42 (0 18 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 082 067 000 - 199640349 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 1 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 56 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 56 [15] occurred at disk power-on lifetime: 6196 hours (258 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 40 50 00 00 00 00 00 e9 00 Error: IDNF 64 sectors at LBA = 0x500009000000 = 87961081217024 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 40 00 09 f8 00 50 80 e9 00 00:15:12.567 READ DMA c8 00 00 00 40 00 09 f8 00 50 40 e9 00 00:15:12.593 READ DMA c8 00 00 00 40 00 09 f8 00 50 00 e9 00 00:15:12.592 READ DMA c8 00 00 00 40 00 09 f8 00 50 70 e9 00 00:15:12.590 READ DMA c8 00 00 00 40 00 09 f8 00 50 30 e9 00 00:15:12.576 READ DMA Error 55 [14] occurred at disk power-on lifetime: 6196 hours (258 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 40 50 00 00 00 00 00 e9 00 Error: IDNF 64 sectors at LBA = 0x500009000000 = 87961081217024 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 40 00 09 f8 00 50 80 e9 00 00:08:05.401 READ DMA c8 00 00 00 40 00 09 f8 00 50 40 e9 00 00:08:05.375 READ DMA c8 00 00 00 40 00 02 1c 00 69 11 e2 00 00:08:05.350 READ DMA c8 00 00 00 40 00 09 f8 00 50 00 e9 00 00:08:05.330 READ DMA c8 00 00 00 40 00 02 3b 00 69 39 e2 00 00:08:05.308 READ DMA Error 54 [13] occurred at disk power-on lifetime: 6192 hours (258 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 40 50 00 00 00 00 00 e9 00 Error: IDNF 64 sectors at LBA = 0x500009000000 = 87961081217024 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 40 00 09 f8 00 50 80 e9 00 00:54:08.602 READ DMA c8 00 00 00 40 00 09 f8 00 50 40 e9 00 00:54:08.596 READ DMA c8 00 00 00 40 00 09 f8 00 50 00 e9 00 00:54:08.586 READ DMA c8 00 00 00 40 00 09 f8 00 50 70 e9 00 00:54:08.585 READ DMA c8 00 00 00 40 00 09 f8 00 50 30 e9 00 00:54:08.584 READ DMA Error 53 [12] occurred at disk power-on lifetime: 6191 hours (257 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 40 50 00 00 00 00 00 e9 00 Error: IDNF 64 sectors at LBA = 0x500009000000 = 87961081217024 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 40 00 09 f8 00 50 80 e9 00 05:28:54.561 READ DMA c8 00 00 00 40 00 09 f8 00 50 40 e9 00 05:28:54.560 READ DMA c8 00 00 00 40 00 09 f8 00 50 00 e9 00 05:28:54.559 READ DMA c8 00 00 00 40 00 09 f8 00 50 70 e9 00 05:28:54.559 READ DMA c8 00 00 00 40 00 09 f8 00 50 30 e9 00 05:28:54.558 READ DMA Error 52 [11] occurred at disk power-on lifetime: 6191 hours (257 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 40 50 00 00 00 00 00 e9 00 Error: IDNF 64 sectors at LBA = 0x500009000000 = 87961081217024 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 40 00 09 f8 00 50 80 e9 00 05:18:03.837 READ DMA c8 00 00 00 40 00 09 f8 00 50 40 e9 00 05:18:03.837 READ DMA c8 00 00 00 40 00 09 f8 00 50 00 e9 00 05:18:03.836 READ DMA c8 00 00 00 40 00 09 f8 00 50 70 e9 00 05:18:03.835 READ DMA c8 00 00 00 40 00 09 f8 00 50 30 e9 00 05:18:03.834 READ DMA Error 51 [10] occurred at disk power-on lifetime: 5233 hours (218 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1d 00 42 0c e1 00 Error: UNC at LBA = 0x11d00420c = 4781523468 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 01 00 01 1d 00 42 0c e1 00 00:20:12.812 READ DMA c8 00 00 00 01 00 01 1d 00 42 0b e1 00 00:20:12.810 READ DMA c8 00 00 00 01 00 01 1d 00 42 0a e1 00 00:20:12.809 READ DMA c8 00 00 00 01 00 01 1d 00 42 09 e1 00 00:20:12.807 READ DMA c8 00 00 00 01 00 01 1d 00 42 08 e1 00 00:20:12.807 READ DMA Error 50 [9] occurred at disk power-on lifetime: 5233 hours (218 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1d 00 42 0c e1 00 Error: UNC at LBA = 0x11d00420c = 4781523468 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 20 00 01 1c 00 42 ff e1 00 00:20:09.016 READ DMA c8 00 00 00 08 00 00 3f 00 60 3f e0 00 00:20:09.016 READ DMA ca 00 00 00 08 00 00 69 00 02 2f e0 00 00:20:09.016 WRITE DMA c8 00 00 00 08 00 01 7f 00 c2 e7 e1 00 00:20:09.016 READ DMA ca 00 00 00 10 00 00 69 00 02 1f e0 00 00:20:09.006 WRITE DMA Error 49 [8] occurred at disk power-on lifetime: 5183 hours (215 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1d 00 42 0c e1 00 Error: UNC at LBA = 0x11d00420c = 4781523468 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 01 00 01 1d 00 42 0c e1 00 00:40:39.452 READ DMA c8 00 00 00 01 00 01 1d 00 42 0b e1 00 00:40:39.452 READ DMA c8 00 00 00 01 00 01 1d 00 42 0a e1 00 00:40:39.452 READ DMA c8 00 00 00 01 00 01 1d 00 42 09 e1 00 00:40:39.452 READ DMA c8 00 00 00 01 00 01 1d 00 42 08 e1 00 00:40:39.452 READ DMA SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS