/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.0-4-amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD5000AAKX-60U6AA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 18.01H18 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri May 26 19:58:15 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 8460) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 86) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 138 137 021 - 4075 4 Start_Stop_Count -O--CK 099 099 000 - 1212 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-K 100 253 051 - 0 9 Power_On_Hours -O--CK 091 091 000 - 7026 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1169 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 099 000 - 1 188 Command_Timeout -O--CK 100 099 000 - 6 190 Airflow_Temperature_Cel -O---K 063 055 040 - 37 (Min/Max 26/38) 192 Power-Off_Retract_Count -O--CK 200 200 000 - 87 193 Load_Cycle_Count -O--CK 200 200 000 - 1124 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 1617 hours (67 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 15 ba a9 27 40 00 Error: UNC at LBA = 0x15baa927 = 364554535 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 f0 00 00 15 ba a9 20 40 00 2d+05:05:31.918 READ FPDMA QUEUED 60 00 08 00 e8 00 00 15 ba b0 e8 40 00 2d+05:05:31.917 READ FPDMA QUEUED 60 00 08 00 e0 00 00 0e 84 83 10 40 00 2d+05:05:31.907 READ FPDMA QUEUED 60 00 08 00 d8 00 00 15 ba b1 40 40 00 2d+05:05:31.907 READ FPDMA QUEUED 60 00 08 00 d0 00 00 15 ba b1 08 40 00 2d+05:05:31.906 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 26/38 Celsius Lifetime Min/Max Temperature: 0/45 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (40) Index Estimated Time Temperature Celsius 41 2023-05-26 17:51 37 ****************** 42 2023-05-26 17:52 ? - 43 2023-05-26 17:53 37 ****************** ... ..( 9 skipped). .. ****************** 53 2023-05-26 18:03 37 ****************** 54 2023-05-26 18:04 ? - 55 2023-05-26 18:05 26 ******* 56 2023-05-26 18:06 26 ******* 57 2023-05-26 18:07 26 ******* 58 2023-05-26 18:08 27 ******** 59 2023-05-26 18:09 28 ********* 60 2023-05-26 18:10 29 ********** 61 2023-05-26 18:11 29 ********** 62 2023-05-26 18:12 30 *********** 63 2023-05-26 18:13 31 ************ 64 2023-05-26 18:14 31 ************ 65 2023-05-26 18:15 32 ************* ... ..( 3 skipped). .. ************* 69 2023-05-26 18:19 32 ************* 70 2023-05-26 18:20 33 ************** 71 2023-05-26 18:21 33 ************** 72 2023-05-26 18:22 33 ************** 73 2023-05-26 18:23 34 *************** ... ..( 2 skipped). .. *************** 76 2023-05-26 18:26 34 *************** 77 2023-05-26 18:27 35 **************** ... ..( 14 skipped). .. **************** 92 2023-05-26 18:42 35 **************** 93 2023-05-26 18:43 36 ***************** ... ..( 67 skipped). .. ***************** 33 2023-05-26 19:51 36 ***************** 34 2023-05-26 19:52 37 ****************** ... ..( 3 skipped). .. ****************** 38 2023-05-26 19:56 37 ****************** 39 2023-05-26 19:57 38 ******************* 40 2023-05-26 19:58 37 ****************** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 6806 Vendor specific