Probe #0cf053e851 of Samsung 700Z3C

Log: smartctl

/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-45-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SanDisk based SSDs Device Model: SanDisk SDSSDP128G Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: 2.0.0 User Capacity: 128,035,676,160 bytes [128 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 1.8 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Sep 6 18:35:58 2020 BST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 24) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O---- 100 100 000 - 0 9 Power_On_Hours -O---- 100 100 000 - 20812 12 Power_Cycle_Count -O---- 100 100 000 - 2254 171 Program_Fail_Count -O---- 100 100 000 - 0 172 Erase_Fail_Count -O---- 100 100 000 - 0 173 Avg_Write/Erase_Count -O---- 100 100 000 - 294 174 Unexpect_Power_Loss_Ct -O---- 100 100 000 - 1035 187 Reported_Uncorrect -O---- 100 100 000 - 0 230 Perc_Write/Erase_Count -O---- 100 100 000 - 980 232 Perc_Avail_Resrvd_Space PO---- 100 100 005 - 0 234 Perc_Write/Erase_Ct_BC -O---- 100 100 000 - 1280 241 Total_LBAs_Written -O---- 100 100 000 - 19403484290 242 Total_LBAs_Read -O---- 100 100 000 - 20869017279 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x03 GPL,SL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 GPL,SL R/O 1 SMART self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3 GPL,SL VS 1 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (16 sectors) Device Error Count: 19 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 19 [18] occurred at disk power-on lifetime: 20764 hours (865 days + 4 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 72 77 73 20 e0 00 Error: IDNF 1 sectors at LBA = 0x72777320 = 1920430880 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 72 77 73 20 e0 00 00:03:02.073 READ DMA EXT 25 00 00 00 01 00 00 72 77 73 20 e0 00 00:03:02.072 READ DMA EXT 25 00 00 00 01 00 00 72 77 73 20 e0 00 00:03:02.070 READ DMA EXT c8 00 00 00 01 00 00 00 03 30 00 e0 00 00:03:02.069 READ DMA c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:03:02.033 READ DMA Error 18 [17] occurred at disk power-on lifetime: 20764 hours (865 days + 4 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 72 77 73 20 e0 00 Error: IDNF 1 sectors at LBA = 0x72777320 = 1920430880 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 72 77 73 20 e0 00 00:03:02.072 READ DMA EXT 25 00 00 00 01 00 00 72 77 73 20 e0 00 00:03:02.070 READ DMA EXT c8 00 00 00 01 00 00 00 03 30 00 e0 00 00:03:02.069 READ DMA c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:03:02.033 READ DMA ca 00 00 00 03 00 00 00 00 00 3b e0 00 00:03:02.009 WRITE DMA Error 17 [16] occurred at disk power-on lifetime: 20764 hours (865 days + 4 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 72 77 73 20 e0 00 Error: IDNF 1 sectors at LBA = 0x72777320 = 1920430880 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 72 77 73 20 e0 00 00:03:02.070 READ DMA EXT c8 00 00 00 01 00 00 00 03 30 00 e0 00 00:03:02.069 READ DMA c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:03:02.033 READ DMA ca 00 00 00 03 00 00 00 00 00 3b e0 00 00:03:02.009 WRITE DMA ca 00 00 00 03 00 00 00 00 00 3b e0 00 00:02:59.418 WRITE DMA Error 16 [15] occurred at disk power-on lifetime: 20757 hours (864 days + 21 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 72 77 73 20 e0 00 Error: IDNF 1 sectors at LBA = 0x72777320 = 1920430880 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 72 77 73 20 e0 00 00:00:26.040 READ DMA EXT 25 00 00 00 01 00 00 72 77 73 20 e0 00 00:00:26.038 READ DMA EXT 25 00 00 00 01 00 00 72 77 73 20 e0 00 00:00:26.036 READ DMA EXT c8 00 00 00 01 00 00 00 03 30 00 e0 00 00:00:26.036 READ DMA c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:25.999 READ DMA Error 15 [14] occurred at disk power-on lifetime: 20757 hours (864 days + 21 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 72 77 73 20 e0 00 Error: IDNF 1 sectors at LBA = 0x72777320 = 1920430880 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 72 77 73 20 e0 00 00:00:26.038 READ DMA EXT 25 00 00 00 01 00 00 72 77 73 20 e0 00 00:00:26.036 READ DMA EXT c8 00 00 00 01 00 00 00 03 30 00 e0 00 00:00:26.036 READ DMA c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:25.999 READ DMA ca 00 00 00 03 00 00 00 00 00 3b e0 00 00:00:25.961 WRITE DMA Error 14 [13] occurred at disk power-on lifetime: 20757 hours (864 days + 21 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 72 77 73 20 e0 00 Error: IDNF 1 sectors at LBA = 0x72777320 = 1920430880 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 72 77 73 20 e0 00 00:00:26.036 READ DMA EXT c8 00 00 00 01 00 00 00 03 30 00 e0 00 00:00:26.036 READ DMA c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:25.999 READ DMA ca 00 00 00 03 00 00 00 00 00 3b e0 00 00:00:25.961 WRITE DMA ca 00 00 00 03 00 00 00 00 00 3b e0 00 00:00:24.393 WRITE DMA Error 13 [12] occurred at disk power-on lifetime: 20755 hours (864 days + 19 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 72 77 73 20 e0 00 Error: IDNF 1 sectors at LBA = 0x72777320 = 1920430880 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 72 77 73 20 e0 00 00:00:26.939 READ DMA EXT 25 00 00 00 01 00 00 72 77 73 20 e0 00 00:00:26.937 READ DMA EXT 25 00 00 00 01 00 00 72 77 73 20 e0 00 00:00:26.935 READ DMA EXT c8 00 00 00 01 00 00 00 03 30 00 e0 00 00:00:26.935 READ DMA c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:26.898 READ DMA Error 12 [11] occurred at disk power-on lifetime: 20755 hours (864 days + 19 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 72 77 73 20 e0 00 Error: IDNF 1 sectors at LBA = 0x72777320 = 1920430880 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 72 77 73 20 e0 00 00:00:26.937 READ DMA EXT 25 00 00 00 01 00 00 72 77 73 20 e0 00 00:00:26.935 READ DMA EXT c8 00 00 00 01 00 00 00 03 30 00 e0 00 00:00:26.935 READ DMA c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:26.898 READ DMA ca 00 00 00 03 00 00 00 00 00 3b e0 00 00:00:26.774 WRITE DMA SMART Extended Self-test Log (GP Log 0x07) not supported Warning! SMART Self-Test Log Structure error: invalid SMART checksum. SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 20793 - # 2 Extended offline Completed without error 00% 19256 - # 3 Extended offline Completed without error 00% 16972 - # 4 Short offline Completed without error 00% 16755 - # 5 Short offline Completed without error 00% 15607 - # 6 Short offline Completed without error 00% 15589 - # 7 Short offline Completed without error 00% 15514 - # 8 Extended offline Completed without error 00% 15421 - # 9 Short offline Completed without error 00% 14892 - #10 Short offline Completed without error 00% 14239 - #11 Short offline Completed without error 00% 14223 - #12 Short offline Completed without error 00% 14118 - #13 Short offline Completed without error 00% 13776 - #14 Short offline Completed without error 00% 13194 - #15 Short offline Completed without error 00% 5111 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 41 --- Current Temperature 0x05 0x010 1 - --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 64 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x05 0x030 1 50 --- Highest Average Short Term Temperature 0x05 0x038 1 50 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 95 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 9 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 67 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0001 2 0 Command failed due to ICRC error /dev/sdb smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-45-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar T7K500 Device Model: Hitachi HDT725050VLA380 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: V56OA7EA User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 T13/1532D revision 1 Local Time is: Sun Sep 6 18:35:58 2020 BST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 128 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 8389) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 140) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--- 240 240 024 - 194 (Average 222) 4 Start_Stop_Count -O--C- 100 100 000 - 1396 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 1 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 020 - 0 9 Power_On_Hours -O--C- 100 100 000 - 2183 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 173 192 Power-Off_Retract_Count -O--CK 099 099 000 - 1469 193 Load_Cycle_Count -O--C- 099 099 000 - 1469 194 Temperature_Celsius -O---- 125 125 000 - 48 (Min/Max 15/58) 196 Reallocated_Event_Count -O--CK 100 100 000 - 1 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 253 000 - 7 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 117 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 117 [0] occurred at disk power-on lifetime: 833 hours (34 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 7f 00 00 38 14 d3 41 68 00 Error: UNC 127 sectors at LBA = 0x3814d341 = 940888897 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 03 03 00 80 00 00 38 14 d3 40 68 00 00:22:07.000 READ DMA EXT 35 03 03 00 02 00 00 1f 05 e7 2a 4f 00 00:22:07.000 WRITE DMA EXT 35 03 03 00 80 00 00 22 17 3d 60 62 00 00:22:07.000 WRITE DMA EXT 35 03 03 00 80 00 00 22 17 3c e0 62 00 00:22:07.000 WRITE DMA EXT 35 03 03 00 80 00 00 22 17 3c 60 62 00 00:22:07.000 WRITE DMA EXT Error 116 [3] occurred at disk power-on lifetime: 812 hours (33 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1f 05 b2 a8 4f 00 Error: UNC 8 sectors at LBA = 0x1f05b2a8 = 520467112 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 03 03 00 08 00 00 1f 05 b2 a8 4f 00 00:14:49.500 READ DMA EXT 25 03 03 00 08 00 00 1f 05 b2 a8 4f 00 00:14:43.900 READ DMA EXT 25 03 03 00 08 00 00 00 60 0c b8 40 00 00:14:43.900 READ DMA EXT 25 03 03 00 08 00 00 00 60 61 80 40 00 00:14:43.900 READ DMA EXT 25 03 03 00 08 00 00 1f 05 b3 08 4f 00 00:14:43.900 READ DMA EXT Error 115 [2] occurred at disk power-on lifetime: 812 hours (33 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1f 05 b2 a8 4f 00 Error: UNC 8 sectors at LBA = 0x1f05b2a8 = 520467112 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 03 03 00 08 00 00 1f 05 b2 a8 4f 00 00:14:43.900 READ DMA EXT 25 03 03 00 08 00 00 00 60 0c b8 40 00 00:14:43.900 READ DMA EXT 25 03 03 00 08 00 00 00 60 61 80 40 00 00:14:43.900 READ DMA EXT 25 03 03 00 08 00 00 1f 05 b3 08 4f 00 00:14:43.900 READ DMA EXT 25 03 03 00 08 00 00 00 60 2c 88 40 00 00:14:43.900 READ DMA EXT Error 114 [1] occurred at disk power-on lifetime: 808 hours (33 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 58 00 00 1f 05 b2 a8 4f 00 Error: UNC 88 sectors at LBA = 0x1f05b2a8 = 520467112 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 03 03 00 80 00 00 1f 05 b2 80 4f 00 00:04:17.100 READ DMA EXT 25 03 03 00 80 00 00 1f 05 b2 00 4f 00 00:04:17.100 READ DMA EXT 25 03 03 00 02 00 00 1f 05 b2 28 4f 00 00:04:17.100 READ DMA EXT 25 03 03 00 80 00 00 1f 05 b2 80 4f 00 00:04:11.400 READ DMA EXT 25 03 03 00 80 00 00 1f 05 b2 00 4f 00 00:04:11.400 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 48 Celsius Power Cycle Min/Max Temperature: --/51 Celsius Lifetime Min/Max Temperature: --/58 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (13) Index Estimated Time Temperature Celsius 14 2020-09-06 16:28 48 ***************************** ... ..( 11 skipped). .. ***************************** 26 2020-09-06 16:40 48 ***************************** 27 2020-09-06 16:41 49 ****************************** 28 2020-09-06 16:42 49 ****************************** 29 2020-09-06 16:43 48 ***************************** ... ..( 2 skipped). .. ***************************** 32 2020-09-06 16:46 48 ***************************** 33 2020-09-06 16:47 49 ****************************** ... ..( 85 skipped). .. ****************************** 119 2020-09-06 18:13 49 ****************************** 120 2020-09-06 18:14 48 ***************************** ... ..( 20 skipped). .. ***************************** 13 2020-09-06 18:35 48 ***************************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0009 2 10 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 10 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdc smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-45-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Pipeline HD 5900.2 Device Model: ST3500312CS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: SC13 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5900 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 1.5 Gb/s (current: 1.5 Gb/s) Local Time is: Sun Sep 6 18:35:58 2020 BST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 192 (intermediate level without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 623) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 108) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 118 099 006 - 191726542 3 Spin_Up_Time PO---- 098 097 000 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 3747 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 084 060 030 - 316846192 9 Power_On_Hours -O--CK 077 077 000 - 20465 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 56 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 094 094 000 - 6 190 Airflow_Temperature_Cel -O---K 061 051 045 - 39 (Min/Max 33/40) 194 Temperature_Celsius -O---K 039 049 000 - 39 (0 10 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 052 030 000 - 191726542 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL,SL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 19083 - # 2 Short offline Completed without error 00% 16849 - # 3 Short offline Completed without error 00% 13058 - # 4 Short offline Completed without error 00% 12578 - # 5 Short offline Completed without error 00% 12194 - # 6 Short offline Completed without error 00% 11714 - # 7 Short offline Completed without error 00% 10706 - # 8 Short offline Completed without error 00% 9755 - # 9 Short offline Completed without error 00% 8331 - #10 Short offline Completed without error 00% 8048 - #11 Short offline Completed without error 00% 6283 - #12 Short offline Completed without error 00% 6093 - #13 Short offline Completed without error 00% 5042 - #14 Short offline Completed without error 00% 4369 - #15 Short offline Completed without error 00% 3054 - #16 Short offline Completed without error 00% 2920 - #17 Short offline Completed without error 00% 2200 - #18 Short offline Completed without error 00% 2200 - #19 Short offline Completed without error 00% 1432 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 150994944 Not_testing 2 825778223 976773167 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 33/42 Celsius Lifetime Min/Max Temperature: 10/49 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 2 minutes Temperature Logging Interval: 94 minutes Min/Max recommended Temperature: 1/61 Celsius Min/Max Temperature Limit: 2/60 Celsius Temperature History Size (Index): 128 (94) Index Estimated Time Temperature Celsius 95 2020-08-29 10:04 42 *********************** 96 2020-08-29 11:38 42 *********************** 97 2020-08-29 13:12 43 ************************ 98 2020-08-29 14:46 42 *********************** 99 2020-08-29 16:20 42 *********************** 100 2020-08-29 17:54 43 ************************ 101 2020-08-29 19:28 43 ************************ 102 2020-08-29 21:02 42 *********************** 103 2020-08-29 22:36 44 ************************* 104 2020-08-30 00:10 44 ************************* 105 2020-08-30 01:44 43 ************************ 106 2020-08-30 03:18 41 ********************** 107 2020-08-30 04:52 42 *********************** 108 2020-08-30 06:26 40 ********************* 109 2020-08-30 08:00 41 ********************** 110 2020-08-30 09:34 43 ************************ 111 2020-08-30 11:08 42 *********************** 112 2020-08-30 12:42 41 ********************** 113 2020-08-30 14:16 42 *********************** ... ..( 3 skipped). .. *********************** 117 2020-08-30 20:32 42 *********************** 118 2020-08-30 22:06 43 ************************ ... ..( 4 skipped). .. ************************ 123 2020-08-31 05:56 43 ************************ 124 2020-08-31 07:30 42 *********************** 125 2020-08-31 09:04 43 ************************ 126 2020-08-31 10:38 41 ********************** 127 2020-08-31 12:12 42 *********************** 0 2020-08-31 13:46 42 *********************** 1 2020-08-31 15:20 42 *********************** 2 2020-08-31 16:54 41 ********************** 3 2020-08-31 18:28 42 *********************** 4 2020-08-31 20:02 42 *********************** 5 2020-08-31 21:36 44 ************************* 6 2020-08-31 23:10 46 *************************** 7 2020-09-01 00:44 44 ************************* 8 2020-09-01 02:18 43 ************************ 9 2020-09-01 03:52 42 *********************** 10 2020-09-01 05:26 43 ************************ 11 2020-09-01 07:00 43 ************************ 12 2020-09-01 08:34 42 *********************** 13 2020-09-01 10:08 42 *********************** 14 2020-09-01 11:42 43 ************************ 15 2020-09-01 13:16 44 ************************* 16 2020-09-01 14:50 43 ************************ 17 2020-09-01 16:24 45 ************************** 18 2020-09-01 17:58 47 **************************** 19 2020-09-01 19:32 46 *************************** 20 2020-09-01 21:06 45 ************************** 21 2020-09-01 22:40 44 ************************* 22 2020-09-02 00:14 43 ************************ 23 2020-09-02 01:48 42 *********************** ... ..( 2 skipped). .. *********************** 26 2020-09-02 06:30 42 *********************** 27 2020-09-02 08:04 43 ************************ 28 2020-09-02 09:38 43 ************************ 29 2020-09-02 11:12 42 *********************** 30 2020-09-02 12:46 ? - 31 2020-09-02 14:20 23 **** 32 2020-09-02 15:54 23 **** 33 2020-09-02 17:28 43 ************************ 34 2020-09-02 19:02 46 *************************** 35 2020-09-02 20:36 ? - 36 2020-09-02 22:10 43 ************************ 37 2020-09-02 23:44 43 ************************ 38 2020-09-03 01:18 44 ************************* 39 2020-09-03 02:52 43 ************************ 40 2020-09-03 04:26 44 ************************* 41 2020-09-03 06:00 39 ******************** 42 2020-09-03 07:34 39 ******************** 43 2020-09-03 09:08 40 ********************* ... ..( 2 skipped). .. ********************* 46 2020-09-03 13:50 40 ********************* 47 2020-09-03 15:24 ? - 48 2020-09-03 16:58 22 *** 49 2020-09-03 18:32 22 *** 50 2020-09-03 20:06 38 ******************* 51 2020-09-03 21:40 39 ******************** 52 2020-09-03 23:14 40 ********************* 53 2020-09-04 00:48 40 ********************* 54 2020-09-04 02:22 ? - 55 2020-09-04 03:56 23 **** 56 2020-09-04 05:30 23 **** 57 2020-09-04 07:04 39 ******************** 58 2020-09-04 08:38 41 ********************** 59 2020-09-04 10:12 ? - 60 2020-09-04 11:46 29 ********** 61 2020-09-04 13:20 29 ********** 62 2020-09-04 14:54 39 ******************** 63 2020-09-04 16:28 40 ********************* 64 2020-09-04 18:02 43 ************************ 65 2020-09-04 19:36 40 ********************* 66 2020-09-04 21:10 38 ******************* 67 2020-09-04 22:44 37 ****************** 68 2020-09-05 00:18 37 ****************** 69 2020-09-05 01:52 36 ***************** 70 2020-09-05 03:26 37 ****************** 71 2020-09-05 05:00 41 ********************** 72 2020-09-05 06:34 36 ***************** 73 2020-09-05 08:08 36 ***************** 74 2020-09-05 09:42 ? - 75 2020-09-05 11:16 27 ******** 76 2020-09-05 12:50 27 ******** 77 2020-09-05 14:24 36 ***************** 78 2020-09-05 15:58 ? - 79 2020-09-05 17:32 27 ******** 80 2020-09-05 19:06 ? - 81 2020-09-05 20:40 33 ************** 82 2020-09-05 22:14 33 ************** 83 2020-09-05 23:48 38 ******************* 84 2020-09-06 01:22 38 ******************* 85 2020-09-06 02:56 38 ******************* 86 2020-09-06 04:30 37 ****************** 87 2020-09-06 06:04 37 ****************** 88 2020-09-06 07:38 37 ****************** 89 2020-09-06 09:12 40 ********************* 90 2020-09-06 10:46 42 *********************** 91 2020-09-06 12:20 42 *********************** 92 2020-09-06 13:54 40 ********************* 93 2020-09-06 15:28 40 ********************* 94 2020-09-06 17:02 40 ********************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 10 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS


Hardware for Linux and BSD

GitHub